kincrome KI 2070 User manual

1
VEHICLE SUPPORT
STANDS
ED4/JAN 22
K12070 K12204 K12075K12074 K12274K12073
Caution: Do not allow persons to operate or assemble these vehicle support stands until they have read this manual
and developed a thorough understanding on how the vehicle support stands works
K12070 - Pin Vehicle Support Stands 1350kg 2 Piece
K12204 - Ratchet Vehicle Support Stands 1850kg 2 Piece
K12073 - Ratchet Vehicle Support Stands 2000kg 2 Piece
K12074 - Ratchet Vehicle Support Stands 3000kg 2 Piece
K12075 - Ratchet Vehicle Support Stands 5000kg 2 Piece
K12274 - Pin & Ratchet Vehicle Support Stands 3000kg 2 Piece

2
VEHICLE SUPPORT STANDS
Part No.:................................................................................K12070
Working Load Limit: .......................................................1350 kg
Minimum Height:.............................................................. 252mm
Maximum Height: ............................................................ 370mm
Lift Height: .......................................................................... 120mm
Saddle Size:..................................................................60 x 51mm
Base Area: ............................................................ 195 x 170mm
Standard: ............................................................... AS 2538:2016
Part No.:................................................................................K12073
Working Load Limit: .......................................................2000 kg
Minimum Height:.............................................................. 293mm
Maximum Height: ............................................................ 424mm
Lift Height: .......................................................................... 131mm
Saddle Size:..................................................................93 x 35mm
Base Area: .............................................................. 215 x 191mm
Standard: ............................................................... AS 2538:2016
Part No.:................................................................................K12075
Working Load Limit: .......................................................5000 kg
Minimum Height:.............................................................. 410mm
Maximum Height: ............................................................ 614mm
Lift Height: .......................................................................... 204mm
Saddle Size:............................................................... 104 x 35mm
Base Area: .............................................................. 280 x 310mm
Standard: ............................................................... AS 2538:2016
Part No.:.............................................................................. K12204
Working Load Limit: ..................................................... 1850 kg
Minimum Height:............................................................. 293mm
Maximum Height: ........................................................... 390mm
Lift Height: ............................................................................95mm
Saddle Size:................................................................ 93 x 35mm
Base Area: .............................................................220 x 200mm
Standard: .............................................................. AS 2538:2016
Part No.:............................................................................... K12074
Working Load Limit: ...................................................... 3000 kg
Minimum Height:..............................................................308mm
Maximum Height: ............................................................450mm
Lift Height: ..........................................................................147mm
Saddle Size:................................................................. 93 x 32mm
Base Area: ............................................................. 235 x 200mm
Standard: ...............................................................AS 2538:2016
Part No.:............................................................................... K12274
Working Load Limit: ...................................................... 3000 kg
Minimum Height:..............................................................308mm
Maximum Height: ............................................................450mm
Lift Height: ..........................................................................147mm
Saddle Size:................................................................. 93 x 32mm
Base Area: ............................................................. 235 x 200mm
Standard: ...............................................................AS 2538:2016
Specifications
Scan QR code for
troubleshooting,
maintenance
& product
information
Scan QR code for
troubleshooting,
maintenance
& product
information
Scan QR code for
troubleshooting,
maintenance
& product
information
Scan QR code for
troubleshooting,
maintenance
& product
information
Scan QR code for
troubleshooting,
maintenance
& product
information
Scan QR code for
troubleshooting,
maintenance
& product
information

3
VEHICLE SUPPORT STANDS
Table of Contents
Specifications...........................................................................................................................................................2
Know Your Product ................................................................................................................................................3
Important Safety Instructions..............................................................................................................................4
Vehicle Support Stands Operation.................................................................................................................. 4-5
Vehicle Support Stands Maintenance and Storage ........................................................................................6
Warranty...................................................................................................................................................................8
Know Your Product
1. Saddle
2. Column
3a. Locking Handle
3b. Locking Pin & flexible wire (K12070 & K12274 only)
4. Base Frame
1
3a
3b
2
4

4
VEHICLE SUPPORT STANDS
Safety Warnings
Save all warnings and instructions for future reference.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in serious injury and/or death.
The use of vehicle support stands has inherent dangers. To avoid risk of personal injury or property damage make sure you are fully
aware of the operating instructions for this product, the recommendations in the vehicle owners manual for jacking of your vehicle
and the safe usage instruction for the jack you will use; all prior to lifting the vehicle.
Do not exceed working load limit of these support stands. These stands are intended for automotive use only. Be aware that large or heavy
vehicles may exceed the stands rated capacity, check vehicle owners manual or contact the vehicle manufacturer.
Do not use for any other purpose except the supporting of a raised vehicle, never use to support any structure or building, do not lift any
human load.
Operation
Preparing Work Area
Before using vehicle support stands and a jack to lift vehicle, it is important to prepare work area properly and CONDUCT A PREOP
ERATIONAL CHECK OF THE EQUIPMENT. Follow this procedure each time a jack and support stands are used to help prevent
property damage and or serious injury.
Caution: ENSURE THAT EACH STAND IS SECURELY LOCATED UNDER A STRONG POINT OF THE VEHICLE. CONSULT THE VEHICLE
MANUFACTURERS MANUAL FOR GUIDANCE. DO NOT EXTEND THE HEIGHT OF THE STAND BEYOND ITS MAXIMUM WORKING
HEIGHT, NOR USE ANY ITEM SUCH AS BRICKS OR TIMBER TO SUPPORT THE VEHICLE. MODIFICATIONS MUST NOT BE CARRIED
OUT OR ACCESSORIES ADDED.
1. Thoroughly inspect vehicle support stands for damage or wear before each use. Briefly test operation of unloaded stands before
using to support any load.
2. Consult vehicle owner’s manual for safety precautions, jacking procedure, vehicle weight, recommended jack type and location
of jack and vehicle support stands areas on vehicle. NEVER EXCEED WORKING LOAD LIMIT. CONFIRM THAT THE LOAD TO BE
APPLIED DOES NOT EXCEED THE WORKING LOAD LIMIT OF THE VEHICLE SUPPORT STANDS.
3. Clear children and others from work area before moving or lifting vehicle. Another adult should be nearby for extra safety and
assistance but must be clear of vehicle as it is moved or lifted.
4. No person should remain in a vehicle that is being jacked or supported by vehicle support stands, No person should enter a
vehicle which is supported by a jack or by vehicle support stands. No person should lean into a vehicle which is supported by a
jack or by vehicle support stands.
5. Clear obstructions from work area. Working in tight or cluttered work areas is dangerous.
6. Be sure vehicle support stands and vehicle are on solid, level ground such as paved or concrete driveway or garage floor. USE
VEHICLE SUPPORT STANDS ON A HARD LEVEL SURFACE, SUCH AS CONCRETE. Uneven or sloped surfaces create hazardous
working conditions and dangerously impeded the function of the support stands.
7. With vehicle in proper position, set vehicle’s parking brake or emergency brake and put gearshift in park (manual transmissions
should be placed in lowest gear). Turn vehicle ignition off and to the “lock” position making sure steering wheel locks.
8. Do not rely on vehicle transmission or brakes to hold vehicle in position. CHOCK THE UNLIFTED WHEELS OF THE VEHICLE. Chock
any wheel not being lifted off the ground to prevent the vehicle rolling. Using wedge-shaped blocks that tyre cannot roll over,
position one chock tight against the tyre in both forward and reverse rolling paths.
9. Vehicle support stands must be used to support vehicle once it is in raised position. USE VEHICLE SUPPORT STANDS IN PAIRS.
Have vehicle support stands capable of supporting vehicle weight ready nearby for use. Read and understand vehicle support
stands manufacturer’s instructions and safety information before use and before lifting the vehicle with this jack.
10. Plan location of jack and vehicle support stands beneath vehicle, making sure jack will be contacting only a jack support area of
vehicle, and vehicle support stands are also positioned in a recommended jack support area. Consult vehicle owner’s manual for

5
VEHICLE SUPPORT STANDS
location of jack support areas. CHECK THAT NO PART OF THE UNDERBODY OF THE VEHICLE WILL FOUL AS THE STANDS
ARE POSITIONED. ENSURE THAT THE LOCKING MECHANISM IS FULLY ENGAGED.
11. DO NOT EXTEND THE HEIGHT OF THE STAND BEYOND ITS MAXIMUM WORKING HEIGHT, NOR USE ANY ITEMS SUCH
AS BRICKS OR TIMBER TO SUPPORT THE VEHICLE. MODIFICATIONS MUST NOT BE CARRIED OUT OR ACCESSORIES
ADDED.
Lifting The Vehicle
Lifting a vehicle using a jack can be dangerous. Follow all instructions and precautions provided by the jack manufacturer.
Do not lift any vehicle with its engine running or start any vehicle that is supported by jack or vehicle support stands.
1. With lifting arm completely lowered, roll jack into position beneath jack support area of vehicle.
2. Inspect position of lifting saddle beneath support area, making sure it is centered and properly engaging support area.
3. Use jack until vehicle is lifted to desired height. Pay attention to lifting saddle position as vehicle is being raised to be sure
there is no danger of jack support area slipping off or lifting from the saddle.
4. Place vehicle support stands under additional vehicle support areas. ALWAYS USE VEHICLE SUPPORT STANDS IN PAIRS.
5. Ensure vehicle support stand locking mechanism is fully engaged.
6. Do not extend the height of the stand beyond its maxiumum height.
7. Check that no part of the underbody of the vehicle will foul as the stands are positioned.
8. SLOWLY lower vehicle down onto vehicle support stands.
9. Lower jack so as saddle does not bear any weight but do not remove jack from jacking position.
Working on Vehicle
Any vehicle being supported by a Jack or Vehicle support stands creates a potentially hazardous working environment.
Do not move or roll a Jack that is supporting a vehicle. Never place any part of your body beneath a vehicle supported by
a Jack. Be careful of forces applied to vehicle such as torque on a nut or bolt. These forces could cause vehicle to become
unstable on Vehicle support stands if they are not properly placed. Do not turn on the vehicle’s ignition or attempt to start any
vehicle supported by a Jack or Vehicle support stands.
Lowering the Vehicle
Caution!: Make certain that all personnel are clear of the vehicle before lowering. Control the rate of descent of the vehicle at
all times. The more you open the Release Valve, the faster the vehicle descends.
1. Re-position jack under same support area used to lift vehicle.
2. Raise Jack until lifting saddle just makes contact with support area under vehicle.
3. Check to be sure lifting saddle is centered under support area. Slowly lift vehicle off from vehicle support stands.
4. Remove vehicle support stands, setting them aside, well clear of vehicle.
5. SLOWLY lower vehicle.
6. Carefully control speed of descending vehicle. Lowering a vehicle too fast can cause property damage or injury.
Maintenance and Storage (Refer to Product Specifications for Maintenance QR codes)
Cleaning
Vehicle support stands should be wiped clean with soft cloth only. Do not use gasoline, kerosene, or other such solvents or any

6
VEHICLE SUPPORT STANDS
abrasive cleanser as cleaning agents and solvents will cause deterioration of the rust protection coating.
Storage
Store vehicle support stands level, in a clean environment preferably indoors, in a dry area to protect vehicle support stands
from moisture.
Repairing Vehicle Support Stands
There are no user serviceable parts. Only trained, licensed and certified repair personnel should attempt any repairs or replacing of
parts. Any modifications to this product, except those performed by the manufacturer, or their designee, will void all warranties both
written and implied.
Office Contact Details:
Phone: [phone]
Fax: [phone]
Email: [email protected]
Website: www.kincrome.com.au
Caring for the environment
When a vehicle support stands is no longer usable it should not be disposed of with household waste, but in an
environmentally friendly way.
Please recycle where facilities exist. Check with your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material
decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council
authority for recycling advice.

7
VEHICLE SUPPORT STANDS
NOTES

www.kincrome.com.au
Office Contact Details:
Phone: [phone]
Fax: [phone]
Email: [email protected]
Website: www.kincrome.com.au
Warranty given by Kincrome Australia Pty Ltd of 3 Lakeview Drive, Caribbean Park, Scoresby, Victoria (Tel [phone]). The applicable warranty
period (24 months) commences on the date that the product is purchased. If this product has materials or workmanship defects (other than defects caused
by abnormal or non warranted use) you can, at your cost, send the product to place of purchase, an authorised Kincrome service agent or one of Kincromes
addresses for repair or replacement. Your rights under this warranty are in addition to any other rights you have under the Australian Consumer Law or
other applicable laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. For further details please visit www.kincrome.
com.au or call us. Due to minor changes in design or manufacture, the product you purchase may sometimes differ from the one shown on the packaging.
Distributed by Kincrome Tools and Equipment
www.kincrome.com.au
3 Lakeview Drive Scoresby Victoria
Phone: [phone]
WARRANTY
YEAR
WARRANTY
2