King Slide 1A89 User manual

規格 / Specifications
尺寸規格 / Dimensional Specifications
King Slide有權變更目錄中所示之產品規格。 實品可能會與圖中所示不同，若兩者相異時，請以最終實品為準，謝謝。
Note :
IYA
• 長度: 250mm to 550mm
• 開啟型式: 全開
• 適用抽牆板厚: 16mm
• 最大荷重: 34 kg(75 lb)/pair
• 安裝型式:抽屜底面
• 材質: 熱浸鍍鋅鋼板
• 高度調整: +3.5mm
• 深度調整: +2.0 /1.0mm
ОX
喇叭頭木螺絲
Wood Screw
系統螺絲
System Screws
8
10
6
7.5
17
4.0
抽屜面板蓋柱式設計
Overlay Drawer Front
抽屜面板入柱式設計
Inset Drawer Front
W: 櫃子的內部寬度 DL: 抽屜長度 X: 抽頭板厚 L: 滑軌長度 IDL: 嵌入抽屜的長度 P: 孔位間距
W: Internal Cabinet Width DL: Drawer Length X: Drawer Front Thickness
L: Slide Length IDL: Internal Drawer Length P: Pitch Between Holes
隱藏式按開滑軌說明書
Installation Instruction for 1A89
■ 孔位圖 / Cabinet hole position ■ 施工間隙 / Space requirements
• Length: 250mm to 550mm
• Travel: Full Extension
• Maximum Drawer Side Thickness: 16mm
• Max. Loading Capacity: 34 kg (75 lb) /pair
• Mount: Undermount
• Material: Galvanized Steel
• Height Adjustment: +3.5mm
• Depth Adjustment: +2.0 /1.0mm
32 32 32
18 18
9 4
37
96
192
288
(max)
1A89-250
1A89-300
1A89-350
1A89-400
1A89-450
1A89-500
1A89-550
W-42
W
+0.5
- 1.5
min 6
max 16
37
21
min 27.5
max 13
*min gap 4
( push-open)
X
Y
Z4=X+4 +*
32
37
min 10
min 10
4(max)
L - 10+X+4*
L-10
+2.0
-1.0
10
10

32
max14
1
結合器安裝 / Locking Device Installation
注意事項 / Notice
3.滑軌是否水平 / All slide members need to be leveled and parelled
4.施工間隙前後是否一致 / Front and rear side spaces need to be consistent.
5.左右邊滑軌位置是否等齊 / Left and right slides need to be aligned to each other
6.勿將產品暴露在粉塵較多之處，以免灰塵進入影響功能 / Do not exposed the product in a dusty environment,
to avoid accumulation of dust which might affect the functions of the slide.
7.請使用吸塵器吸起灰塵、勿用噴槍 / Use vacuum cleaner for dust cleaning, do not use air spray gun.
8.請用不起毛球的軟布擦拭即可，勿用清潔劑，並於日後保持乾燥 / To maintain the slide, please use a
soft cloth without lint to wipe the slide, do not use detergent and keep the slide in a dry environment.
1.運輸時 / Transport 2.確認抽屜是否方正 /
Drawer needs to be squared
免工具調整 / Tool-less Adjustment
Note: King Slide reserves the right to alter specifications of all the products without notice. The actual product may vary from the illustration, If the entity is different from the illustration then please refer to the entity, thank you.
只需轉動前端滾輪即可輕鬆地調整高度
Simply rotate the wheel at the
front bottom of the drawer to
adjust the drawer height.
輕壓分離器即可分離抽屜
Simply press the front release
device to remove the drawer.
引孔治具 (選購品) / Drilling template (Optional)
抽屜前端
Drawer front
抽屜後方
Drawer rear
6.0mm鑽頭
6.0mm drill bit
2.5mm鑽頭
2.5mm drill bit
結合器安裝 / Locking Device Installation
滑軌安裝 / Drawer Slide Installation
抽屜安裝 / Drawer Installation
Eject Force Adjustment
-1.0
4.0
+2.0
Front Gap Adjustment
Factory Setting
原廠設定
深度調整
彈力調整
往外
往外
往外
往內
Inward
Outward
Outward
Inward
+ =
Max.
Min.
最小
最大