Kingtel KT-6450D User manual

KT-6450D/D6
DECT / DECT6.0 Big Button Emergency Phone
+ Portable Talking Pendant

Declaration of conformity
Hereby, KINGTEL Corp. declares that this KT-6450D product is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. Acopy of the
Declaration of Conformity can be found at http://www.kingtel.com.tw.
Disclaimer and limitation of liability
KINGTEL Corp. and its affiliates or licensees assume no responsibility for any damage or loss
resulting from the use of this guide. KINGTEL Corp. and its affiliates or licensees assume no
responsibility for any loss or claims by third parties that may arise through the use of this
software. KINGTEL Corp. and its affiliates or licensees assume no responsibility for any
damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs.
Be sure to make backup copies of all important data on other media to protect against data
loss.
TO THE MAXIMUM EXTENT PERMITTED BYAPPLICABLE LAW, UNDER NO
CIRCUMSTANCES SHALL KINGTEL CORP. OR ANY OF ITS AFFILIATES OR LICENSEES
BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS
OF THIS DOCUMENT ARE PROVIDED “AS IS.” EXCEPT AS REQUIRED BY APPLICABLE
LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR APARTICULAR PURPOSE, ARE MADE IN RELATION TO THEACCURACY,
RELIABILITY, OR CONTENTS OF THIS DOCUMENT. KINGTEL CORP. RESERVES THE
RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR
NOTICE.
FCC Notice
Your unit may cause TV or radio interference (for example, when using a telephone in close
proximity to receiving equipment). The Federal Communications Commission (FCC) of the
United States can require you to stop using your phone if such interference cannot be
eliminated. If you require assistance, contact your local service facility. This device complies
with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any changes or
modifications not expressly approved by KINGTEL Corp. could void the user’s authority to
operate this device.

FCC INFORMATION
Part 68 is a Federal regulation which requires equipment to be tested and registered with the
FCC prior to its connection to the network. This equipment complies with Part 68 of FCC rules.
On the bottom of the telephone is a label that contains, among other information, the FCC
Registration Number and the Ringer Equivalence Number (REN) for this equipment. You must,
upon request, provide this information to your telephone company.
The Ringer Equivalence Number, which is used to determine the number of devices you may
connect to your phone line, indicates the amount of power that your telephone draws from the
telephone company line during ringing. If you have more than one telephone (or other terminal
device) connected to the telephone company line, you should total the ringer equivalence
numbers (REN s), and be sure that the total is not more than five. Your telephones may not
ring if the total is more than five. Also, in some rural locations, your telephone may not ring if
the REN total is more than three.
RESTRICTIONS You must not connect your telephone to coin-operated lines or party lines.
INSTALLATION This model telephone must be connected to the telephone company lines
through a modular jack. The required USOC for the modular jack is RJ11C for desk mounting
and RJ11W for wall mounting. The USOC number is printed on the label on the bottom of your
telephone.
HEARING-AID COMPATIBILITY The handset on your telephone will work with
magnetically-coupled hearing aids. You can use a hearing aid equipped with a T (Telephone)
switch.
IN CASE OF TROUBLE If your telephone should cause problems on the telephone line, the
telephone company can temporarily disconnect your service. The telephone company must
then notify and allow you to correct the problem.
The telephone company may from time to time change its lines or equipment. They must notify
you if planned changes will affect your telephone service, to allow you to take steps to prevent
interruptions.
Part 15 regulates the electromagnetic energy emitted by equipment to minimize interference
to radio, television, and other wireless devices. This telephone complies with Part 15 of the
FCC Rules. In the unlikely event that interference occurs, move the telephone and/or radio,
television, etc. to increase the separation distance.

The installation of the base unit should allow at least 20 centimeter between the base and
persons to be in compliance with FCC RF exposure guidelines. For body worn operation, the
portable part (handset) has been tested and meets FCC RF exposure guidelines.
This device must not be co-located or operating in conjunction with any other antenna or
transmitter. The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
IC Information
This product meets the applicable Industry Canada technical specification.
1. The Industry Canada label identifies certified equipment. This certification means that the
equipment meets telecommunications network protective, operational and safety requirements
as prescribed in the appropriate Terminal Equipment Technical Requirements documents(s).
The department does not guarantee the equipment will operate to the user's satisfaction.
2. Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that
compliance with the above conditions may not prevent degradation of service in some
situations.
3. Repairs to certified equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.
4. Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact
the appropriate electric inspection authority, or electrician, as appropriate.
5. The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the ringer equivalence Numbers of all the devices does
not exceed 5.

© 2009 KINGTEL Corp. All rights reserved.

Important Safety Instructions
Always follow basic safety precautions when using your telephone to reduce the risk of fire,
electrical shock and injury.
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing
serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To
protect it from overheating, these openings must not be blocked or covered. The openings
should never be blocked by placing the product on the bed, sofa, rug, or other similar surface.
This product should never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your dealer
or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord
will be damaged by persons walking on it.
9. Do not overload wall outlet extension cords, as this can result in the risk of fire or electric
shock.
10. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric shock.
Never spill liquid of any kind on this product.
11. To reduce the risk of electric shock, do not disassemble this product. Instead, when some
repair work is required, take the unit to a qualified technician. Opening or removing covers may
expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric
shock when the appliance is subsequently used.
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating 6 instructions.
Adjust only those controls that are covered by the operating instructions because
improper adjustment of other controls may result in damage and will often require

extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or cabinet has be damaged.
f. If the product exhibits a distinct change in performance.
13. Avoid using a telephone during an electrical storm. There may be a risk of electrical shock
from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Plug the power adaptor into an electrical outlet that is near the equipment and easily
accessible.
Safety Instructions for Handset Battery Pack
CAUTION:
There is a danger of explosion if the batteries are incorrectly replaced. Use only approved
batteries in the handset of your telephone. To reduce the risk of fire or injury, be careful not to
short the batteries with conducting materials such as rings, bracelets, and keys. The batteries
or conducting material may overheat and cause burns.
BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY
1. Do not dispose of the batteries in a fire. They may explode. Check with local codes for
possible special disposal instructions.
2. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
3. Exercise care in handling batteries in order not to short the battery with conducting materials
such as rings, bracelets and keys. The battery or conductor may overheat and cause burns.
4. Charge the batteries only in accordance with the instructions and limitations specified in this
manual.
5. Observe proper polarity orientation for the batteries as marked in the telephone.
6. Do not mix old and new batteries.
7. Do not mix batteries of different sizes or from different manufacturers.

DESCRIPTION
KT-6450D is specifically designed for minimizing the negative impact of people who stay alone.
The product provides exceptional security mechanism in emergent cases that
pre-programmed telephone numbers are dialed automatically in sequence through one touch
of SOS button on portable pendant, and pre-recorded alert message is played once the call is
answered, thus to prevent undesired emergencies from happening in advance.
PRODUCT FEATURES
Base
‧ DECT/DECT 6.0 technology with interference free communication
‧ Adjustable amplified corded handset volume up to 20dB Gain for comfortable listening
‧ 3 emergency one-touch keys
‧ 10 alarms serve for medication reminder
Pendant
‧ Maximum 4 portable talking pendant per base
‧ Water-resistance design
‧ Hearing aid compatible
‧ Press SOS key, up to 10 preset numbers will be dialed in sequence
‧ Low battery indication & warning tone
‧ Outdoor range up to 200m
‧ Auto standby up to 200 hrs; talking up to 8 hrs

PRODUCT SPECIFICATION
Telephone
‧ 5 adjustable Handset volume level
‧ 5 adjustable Speaker volume level
‧ 5 adjustable Ringer volume level & off
‧ 10 dialed numbers review & redial
‧ 80 phonebook entries, 12 characters for each name, 24 digits for each number
‧ On-hook pre-dial and dial number editing
‧ Flash time (100/300/600/1000ms) adjustable
‧ Adjustable receiving tone (optional)
Caller ID
‧ FSK/DTMF
‧ Call waiting caller ID
‧ Backlight LCD display
‧ LCD 3 lines display: 1 line icon, 1 line 5*7 Dot Matrix of 12 characters, 1 line 16 digits of
7-segment
‧ 5 adjustable LCD contract level
‧ 100 Caller ID memories for incoming/missed calls

KT-6450D
Telephone Part Identification

1 LCD Display Display phone number, date, time and other information
2 MENU / SELECT Press to access main menu (on-hook / off-hook mode)
Press to enter sub-menus (on setting mode)
Press to confirm setting (on setting mode)
3 ▼Press to show received calls (on-hook mode)
Press to turn volume down (off-hook mode)
Press to turn volume down (speakerphone mode)
Navigation key
4 ▲Press to show missed calls (on-hook mode)
Press to turn volume up (off-hook mode)
Press to turn volume up (off-hook mode)
Navigation key
5 DELETE / FLASH Press to delete the incorrect number when dialing
(on-hook / off-hook mode)
Press to clear/delete character or digit when editing
contact information (on setting mode)
For PBX (speakerphone mode)
6 Phonebook / ESC Press to enter the phone book operation
Press to return to upper menu
7 SOS Press to trigger SOS function
8 ＋
＋＋
＋Press to contact local hospital (Service varies depend on
service provider)
9 POLICE Press to contact local police office (Service varies depend
on service provider)
10 REDIAL / PAUSE Press to review outgoing numbers (on-hook mode)
Press to dial last dialed number (off-hook mode)
Press to dial last dialed number (speakerphone mode)
11 Press to activate or deactivate speakerphone
The light blinks when there is an incoming call
12 Press to enable intercom and conference call
Press to page the pendant
13 Hook On / Off Switch Press to end / start the a call
14 Wall Mounting Hook Turn 180 degree to hang up the handset when the unit is
mounted on the wall
15 Dialing key (0-9, ＊,
＃)
Dial numbers and extensions

16 Handset cord jack
17 Power line jack
18 Telephone line jack
19 Battery compartment
20 SOS key
21 In charging light
22 Power line jack
23 Battery connector
24 Battery cover of pendant

Menu setting
During standby mode, press MENU/SELECT key to enter the menu setting, and there are
totally six (6) sub-menus as below:
1) CALL LOG
2) PHONE BOOK
3) BS SETTINGS
4) PENDT SETUP
5) SOS SETTINGS
6) AUTO ANSWER
7) REGISTRATION
Press ▲or ▼key to select one of the above items & press MENU/SELECT key again to
enter/confirm the selected item. Details of each item are shown in next parts.
CALL LOG
The first menu is CALL LOG.
There are two items in this menu, RECEIVED calls and DIALED calls
Using ▲or ▼key to select.
Press MENU/SELECT key to enter received call list or dialed call list.
The LCD shows the last record. If no entries are available in the list, empty will
be shown on the LCD.
Press ▲or ▼key once to view other record.
Press MENU/SELECT key when record is shown and you can access:
ADD TO PB: This allows the user to add the entry from the caller list to the phonebook
DELETE: This allows the user to delete the currently selected entry from caller list
DELETE ALL: This allows the user to delete all entries in the caller list
Press ▲or ▼key to choose among 3 activities and press MENU/SELECT key to confirm.

PHONEBOOK
The memory capacity of phone book for contact information is 80 that contain name and phone
number. Each name has maximum 12 characters and each number has maximum 24 digits.
LIST
This function allows the user to review the phonebook list and make a call directly from the
phonebook list.
Press MENU/SELECT key.
Using ▲or ▼key and select PHONE BOOK.
Press MENU/SELECT key to enter.
Then LCD shows: LIST
* The function allows the user to review the phone book list by using ▲or ▼key. The LCD
shows empty if no contact information in phone book
NEW ENTRY
This function allows the user to add a new entry to the phonebook.
Press ▲or ▼key and select “NEW ENTRY” item.
* The display shows blinking “_”, enter name by using the alphanumeric keys.
** If you input incorrect character, press DELETE/FLASH key to correct.
*** Press MENU/SELECT key to confirm.
Enter the number and select the melody to be stored & press MENU/SELECT key for
confirmation, a sound will be heard once the setting succeeds.
Note 1: If the phonebook capacity is full and more contact information is added, a message
will be presented to the user on LCD as “MEM IS FULL”.
Note 2: In special melody for specific number, the melody will be heard only in the second ring.
(First ring will be normal and from the second ring of this number, there will be the special ring
selected for this number)

EDIT RECORD
This function allows the user to modify a stored phonebook record.
Press ▲or ▼key and select “EDIT RECORD” item.
* Press MENU/SELECT key to enter, the first record in the phone book will be displayed.
** Press ▲or ▼to select the desired stored record which you want to edit.
*** Press MENU/SELECT key to enter for editing.
**** Press ▲or ▼or MEMU/SELECT key to edit.
***** Once a stored record has been selected, the user has the option to edit each of the
names/number and or change the melody as well.
Press MENU/SELECT key to confirm the changes, a sound will be heard once the
setting succeeds.
DEL RECORD
This function allows the user to delete a stored phonebook entry.
Press ▲or ▼key and select “DEL RECORD” item.
Press MENU/SELECT key to enter, and using ▲or ▼to select the desired stored
record which you want to delete.
Press MENU/SELECT key to enter for deleting.
Press MENU/SELECT key to confirm, a sound will be heard once the setting succeeds.
DELETE ALL
This function allows the user to delete all stored phonebook entries.
Press ▲or ▼key and select “DELETE ALL” item.
Press MENU/SELECT key to enter for deleting all entries.
Press MENU/SELECT key to confirm, a sound will be heard once the setting succeed.
MEM STATUS
This function allows the user to check phone book memory capacity
Press MENU/SELECT key to enter for viewing “MEM Status” item.
* If shows 10/80, it means there are 10 out of 80 records stored in phone book.

BS SETTINGS
Combination is needed to enter BS setting; the default combination is “0000”
The user is able to change the base setting.
Pressing MENU/SELECT key and using ▲or ▼key to select “BS SETTINGS” item.
Press MENU/SELECT key to enter.
RING SETUP
The user is able to change the base ringer for internal calls and External calls.
There are totally 6 ring melodies and 6 volume levels (Exp: volume 1, 2, 3, 4, 5, off).
Press MENU/SELECT key, then using ▲or ▼key to select “RING SETUP” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key and select the INT RING or EXT RING setup.
Press MENU/SELECT key to confirm.
Press ▲or ▼key and select MELODY or VOLUME setup.
After select, press MENU/SELECT key to confirm.
Press ▲or ▼key and select the desired melody, the corresponding melody sound
can be heard with the selection.
After selecting desired VOLUME, press MENU/SELECT key to confirm.
Press ▲or ▼key and select desired ringer volume 1-5, off, the corresponding volume
sound can be heard.
Press MENU/SELECT key to confirm your selection before exit, a sound will be heard
once the setting succeed.
DIAL MODE
The user can select to change the dialing mode in base XXX.
Press MENU/SELECT key, then using ▲or ▼key to select “DIAL MODE” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key to select TONE or PULSE as dial mode.
Press MENU/SELECT key to confirm your selection before exit, a sound will be heard
once the setting succeed.

FLASH TIME
The user can change the flash time (100ms, 300ms, 600ms and 1000ms).
Press MENU/SELECT key, then using ▲or ▼key to select “FLASH TIME” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key to select the 100ms, 300ms, 600ms and 1000ms.
Press MENU/SELECT key to confirm your selection before exit, a sound will be heard
once the setting succeeds.
ALARM
The user can set up 10 alarms as medication reminder
Press MENU/SELECT key, then using ▲or ▼key to select “ALARM” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key to select Alarm 1-10, and select “ON” or “OFF”.
Press MENU/SELECT key to set up the time before exit, a sound will be heard once the
setting succeed.
KEY TONE
The user is able to change the BASE key tone.
Press MENU/SELECT key, then using ▲or ▼key to select “KEY TONE” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key and select the “ON” or “OFF” to enable/disable the sounding of the
beep respectively.
Press MENU/SELECT key to confirm your selection before exit, a sound will be heard
once the setting succeed.
LANGUAGE
The base unit supports 8 languages.
English, Dutch，French, German, Spanish, Italian, Danish, Svenska
Press MENU/SELECT key, then using ▲or ▼key to select “LANGUAGE” item.
Press MENU/SELECT key to enter. English is displayed in first row of language list.
Press ▲or ▼key to select the language. Each language displays in its own native
translation
Press MENU/SELECT key to confirm your selection before exit, a sound will be heard
once the setting succeed.

DATE & TIME
The user is able to set the date and time on the BASE,
Press MENU/SELECT key and using ▲or ▼key to select “DATE & TIME”,
Press MENU/SELECT key to enter.
The last two digits of the Year are blinking on LCD showing as “20_ _”.
Press ▲or ▼key and enter the desired year.
Press MENU/SELECT key to confirm.
Then DATE & TIME will show on the LCD, enter the desired DATE/TIME by ▲
or ▼key when it blinks on the corresponding position.
The setting will be saved after pressing MENU/SELECT key, a sound will be heard
once the setting succeed.
Note: The time and date will be automatically set when the first Caller ID message is received
and it depends on the service local telecom provides.
MODIFY PIN
This function allows the user to modify pin code for entering the menu.
The factory default code is a 4 digit code (0000)
Press MENU/SELECT key, then using ▲or ▼key to select “MODIFY PIN” item.
Press MENU/SELECT key to enter.
The user will be prompted to enter the current pin code.
Press MENU/SELECT key to confirm.
The user will be prompted to enter new pin code
Press MENU/SELECT key to confirm.
The user will be prompted to repeat the new pin code.
Press MENU/SELECT key to confirm, a sound will be heard once the setting succeed.

BS DEFAULT
This function allows the user to restore the base setting to the factory default.
Press MENU/SELECT key, then using ▲or ▼key to select “BS DEFAULT” item.
Press MENU/SELECT key to enter.
The user will be prompted to press MENU/SELECT key to confirm, a sound will
be heard once the setting succeeds. (It takes 3 seconds to make a default setting
succeed, when the unit will also go off and on during this time).
DEL PENDT
This function allows the user to delete a pendant registration from the base.
If the pendant has been deregistered, it doesn’t work and need to register with the base again.
Press MENU/SELECT key, then using ▲or ▼key to select “DEL PENDT” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key will scroll the pendant names list up and down, select the pendant
you want to deregister.
Press MENU/SELECT key to confirm. The pendant will be deleted from the registration
list of base, and the pendant starts sounding out of range warning tone.
PENDANT SETUP
Combination is needed to enter BS setting; the default combination is “0000”
The user is able to change the settings of pendant to their own preferences.
Pressing the MENU/SELECT key and using ▲or ▼key to select “PENDT SETUP”
item.
Press MENU/SELECT key to enter.
The LCD will show the registered pendant. Example: PENDT1.
Press MENU/SELECT key to confirm.

INT RING
The user is able to change the pendant ring tone for internal call. There are 6 ring melodies
and 6 volume levels (For volume 1, 2, 3, 4, 5 & OFF).
Press MENU/SELECT key, LCD shows “INT RING” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key and select MELODY or VOLUME setup.
After select MELODY, press MENU/SELECT key to enter.
Press ▲or ▼key to select desired melody.
Press MENU/SELECT key to confirm, a sound will be heard once the setting succeed.
If VOLUME is selected, press MENU/SELECT key to enter.
Press ▲or ▼key to select desired ringer volume 1-5, if you want to switch off volume,
then select “OFF”,
Press MENU/SELECT key to confirm, a sound will be heard once the setting succeed.
EXT RING
Kindly follow the same instructions of internal ring (as above).
AUDIO SETUP
The user is able to set the pendant audio settings.
Press MENU/SELECT key, then using ▲or ▼key to select “AUDIO SETUP” item.
Press MENU/SELECT key to enter.
Press ▲or ▼key to select “SPK VOLUME”.
Press ▲or ▼key to select desired volume 1-5.
Press MENU/SELECT key to confirm, a sound will be heard once the setting succeeds.
SOS SETTINGS
Combination is needed to enter BS setting; the default combination is “0000”
The user is able to change SOS settings.
Press MENU/SELECT key and use ▲or ▼key to select “SOS SETTINGS” item/
Press MENU/SELECT key to enter.
Press ▲or ▼key to select the sequence of SOS number that is to be stored as form
“SOS NUMBER 1” to “SOS NUMBER 10”.
Press MENU/SELECT key to confirm.
Enter the SOS number to be stored by using the alphanumeric keys
Press MENU/SELECT key to confirm, a sound will be heard once the setting
succeeds