Control Lock
_ ControlLock 1
Hold 3Sec
or
OPTIONS CAN BE WHAT IT DOES
SELECTED WITH ADDED TIME TO CYCLE
TYPICAL MAX
ADDED
WATER
GALLONS
(LITERS)
Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.
Toturn on Lock, press and hold CONTROL LOCK or 8 HOUR DELAY (depending on model) for 3 seconds. The Control
Lock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. Ifyou press any button
while your dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the
controls are locked.
NOTE: You may need to disable Sleep Mode by pressing either START/RESUME or CANCEL, or by opening and
closing the door before you are able to turn Control Lock off.
Toturn off Control Lock, press and hold CONTROL LOCK or 8 HOUR DELAY (depending on model) for 3 seconds. The
light turns off.
NOTE: If your model requires you to press and hold 8 HOUR DELAY to lock the controls, the Control Lock LED will be
on or off to indicate if Control Lock is active or not.
CONTROL PURPOSE COMMENTS
To start or resume a If the door is opened during a cycle or the power is interrupted, the Start/Resume indicator
wash cycle flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.
NOTE: If the Starb'Resume button is located on top of door, push door firmly closed within
_. R_pe.tL.,tcyd_ 3 seconds of pressing START/RESUME. f the door is not closed within 3 seconds the
StartJResume button LED wi!! flash, an audible tone wil! be heard, and the cycle wi!l not
start.
--CANCEL/
1DRA|N I
To reset any cycle or
options during
selection.
To cancel a wash
cycle after it's
started.
Press and hold CANCEL/DRAIN to reset any control selections made.
See "Canceling A Cycle After Dishwasher Is Started" and "Changing A Cycle After
Dishwasher Is Started" sections.
To turn the audible Press and hold the Hi.Temp scrub button for 3 SecOnds to turn the audible tones On croft.
-} tones on or off. Only audible tones for confirming button presses can be turned on!off. Important audible
Hi-TempjScrub tones, such as indicating a CYC!ehas been interrupted, cannot be deactivated.
CONTROL PURPOSE COMMENTS
The Cycle Status Indicator Clean indicator glows when a cycle is finished.
Washin_ Drying Clean Sanitized
• = • • Dghts are used to follow the
,,,,,_',_ofo _÷_,_,,4_'o_,,._,_,; lfyou select the Sani Rinse option; when the Sani Rinse cycle is finished,
, , { , , _. _ the Sanitized indicator glows, If your dishwasher did not properly sanitize
cycle Locatea on tne Tront
"f the dis_'was _. for f,_nt your dishes, the light flashes at the end of the cycle. This can happen if the
'_ . .......... . cycle sinterrupted, or the water could not be heated to the required
contro! moc_e!s,anc_Iocatea tem..erat, re
p u
on the top of the door for i
hidden contro! models. The Clean and Sanitized lights go offwhen you open and close the door or
press and hold CANCEL
AThe Front Indicator Light or
Single Exterior Light (A)
shows progress of your
dishwasher cycle by color
(for hidden control models
only).
The light will be blue if the dishwasher is washing or rinsing. The light will
be red when the dishwasher is drying. The light will be green to indicate
that the cycle is complete. If the Front Indicator Light is blinking, see
"Troubleshooting" section.
The Cycle Status Display is The indicators will inform you if you are ab!e to add a dish to the cycle after
Used to follow the progress it has started. It will also inform you if the dishwasher is washing, rinsing,
of the dishwasher cycle, and drying, complete, and/or sanitized, They will show whether the control is
to show other information, locked and/or the delay oPtion is selected. A series of bars will count down
(Available on some models the duration of the cycle remaining from left to right. Each bar equals
instead of Cycle Status approximately 24 minutes of cycle lengthl The bars will also count down
10
