Kkmoon TS-838 User manual

15/07/12
Consumer Electronics
User Manual
E44395_Power meter_PT_IM_PRINT.indd 1
Energy Meter
TS-838

2 3
............................ 4
Before using the appliance... ....................................... 4
Proper Use
.......................................................................5
Safety Warnings ........................................................... 6
Recommendations for the use of batteries........ 9
Symbols: explanations .............................................11
Commissioning .............................................................11
Replacement of batteries .........................................12
Item description ........................................................14
LCD
..................................................................................15
Overview of functions............................................. 16
Preparation ..................................................................18
Regular time ...............................................................18
Indication of 12/24 hours
.......................................19
......................................19
Introduction price for electricity at night ..... 22
Performing the measurement ........................... 26
See the reading ........................................................... 27
Delete the values measured ...................................28
History of consumption...........................................29
.................. 30
Overload
....................................................................... 30
Power factor
................................................................. 31
Troubleshooting
........................................................ 33
Indications not common in the screen
preview
.........................................................................33
Clean
...............................................................................33
Protection of the environment ..............................34
Disposal of batteries ..............................................34
Disposal of used appliances
............................. 35
Packaging
.................................................................... 35
Technical Data.............................................................36
Accuracy of measurement
....................................37
Declaration of Conformity
................................... 37
Warranty conditions
................................................. 38
Warranty Card
...........................................................41
E44395_Power meter_PT_IM_PRINT.indd 2-3
Thank you for your confidence!
Setting the price per kWh
Other functions (for professionals)
Index

4 5
Thank you for your confidence!
Before using the appliance
Proper Use
E44395_Power meter_PT_IM_PRINT.indd 4-5
We congratulate you on your purchase of your
new gauge of the cost of electricity.We are sure
that you will be satisfied with this modern
appliance.
This device will help you ascertain the costs of
energy consuming appliances.We hope that you
can find all "electricity hogs" and, thus, minimize
your electricity costs.
After unpacking and before each use verify that
the article presents damage.If this is the case can
not use the article please contact your seller.
The operating manual is in compliance with the
rules and regulations in force in the European
Union.Abroad also note the directives and
specific legal provisions-country-!
Before using your appliance first
carefully read the safety warnings and
instructions.
So you can use all the functions in a safe and
secure way. Keep very well the instruction manual
as well as the receipt of proof of purchase and, if
possible, on the packaging. If you lend, offer or
sell the handset, also delivered the instruction
manual.
The apparatus used to determine in consumption
of energy consuming devices connected and the
resulting costs.
The article is suitable only for private use and
not designed for commercial use.
Use only in accordance with the instructions
described in this manual d. Any other use is
considered appropriate and may cause damage
or even lead to injury.

6 7
Adverse competences security
•
•
•
•
•
•
•
•
•
•
•
E44395_Power meter_PT_IM_PRINT.indd 6-7
The manufacturer does not assume any
responsibility-made by damage or caused by
using inappropriate.
Before putting your electricity cost meter in
operation will take into consideration the
following points:
An electrical installation or a botched network
voltage too high can lead to electrical shock.
The device is suitable only for use with
230 V / 50/60 Hz AC.
Only connect the appliance to an outlet
with contacts 230 V protection that has
been properly installed.
Do not use the appliance if it is visibly
damaged or if the mind for power cord or
plug is defective.
Do not open the structure of the
equipment, ask for your seller to repair
specialists.
It should be taken to a specialist
workshop. In the case of attempted
repairs inde-pendent,a bad connection
or a wrong operation cease all rights
regarding liability and warranty.
Only use the unit indoors and dry.
Never operate the unit in humid or
abroad.
The unit can not come into contact
with sprayed water or other liquids.
Keep a minimum distance of one
meter from sources of moisture
such as washbasins.
Never hold the device if your hands
are wet.
Never grab an electrical appliance
after it has fallen into the water. In a
situation Semel-hante immediately
Do not tamper with the device.
Do not connect multiple metered
electricity costs among themselves,

8 9
•
•
•
•
•
•
Danger of explosion!!
•
•
•
•
E44395_Power meter_PT_IM_PRINT.indd 8-9
Do not cover the appliance with other materials
by exists the danger of overheating.
When not using the device or if a malfunction
occurs, disconnect the power source.
Dangers for children!
Often children do not recognize or
underestimate the dangers.
Keep bags and materials used to pack the
machine away from babies and small
children. Danger of suffocation!
This appliance is not suitable for use by
persons (including children) with a
capacity of physical, sensory or
intellectual abilities, or who does not
experience and / or sufficient knowledge,
unless they are under the supervision of a
person that is responsible for their safety
or that have had instructions on how to
operate the device.
Supervise children and keep the
appliance out of their reach to ensure
that they do not play with the appliance.
The their misuse means danger of
electric shock!
Recommendations for the use of batteries
The meter cost of electricity in the functional
with 2 batteries (button) of the type LR44 or
AG13 (these batteries are included).
Only use the battery type here specified,
in order to prevent fire. Never attempt
to charge the batteries.
Do not throw batteries into a fire, not short-circuit
the batteries or try to take them apart!
Keep batteries out of reach of children.
Seek immediate medical attention if
swallowing a battery.
Immediately remove the batteries inside
the device! Heightened risk of leakage!
Those cells not exposed to extreme
conditions, such as heaters over! As in
radiators or in direct sunlight!
Heightened risk of leakage!

10 11
•
•
•
•
Symbols: Explanations
CAT II
300 V
Commissioning
E44395_Power meter_PT_IM_PRINT.indd 10-11
Avoid contact with skin, eyes and mucous
membranes. In case of contact with battery
acid, immediately wash the affected area
with plenty of clean water and seek
medical attention immediately.
Only use batteries of the same type, not
simultaneously use batteries of different
types not mix old batteries with new
batteries.
Always replace both batteries at the
same time.
If necessary, clean the battery contacts
and device before placing the stack.
You can the following symbols on the device:
Only be used in enclosed spaces
Note concerning the disposal of
used appliances (see page 35)
The instrument is approved for
electrical circuits that if you find
the train connected directly to the
network of low voltage
The batteries come included with the appliance.
Colo-batteries to work removing the insulation
strips compartment. To open the battery
compartment act according to what is shown below.

12 13
Replacement of batteries
1. Unplug the appliance.
2.
3.
4.
5.
Information：
E44395_Power meter_PT_IM_PRINT.indd 12-13
To replace batteries ，remove the two
screws with a screwdriver and loosen the
lid of the battery compartment.
Remove dead batteries and proceed to
disposal / recycling collection point for used
batteries.
Insert two new batteries (button cells
1.5 V, type LR44/AG13) in the battery
compartment.
By introducing them note-to correct the
polarity (+ / ), as shown in the lower
compartment.
Replace the battery compartment cover and
tighten the screws with a screwdriver.
The battery compartment just leave to introduce a
direction, pay attention to the contours of the
structure.
Before placing the appliance in operation of the
battery compartment must be completely inserted.
If not use the device for some time remove the
batteries from the inside in order to avoid that
spend complete

14 15
Description of Article
1
2
3
4VALUE H/ +:
5
6
LCD
7
8
9
7
8
9
1
2
3
4
5
6
E44395_Power meter_PT_IM_PRINT.indd 14-15
LCD Display for the
,sgnidaerehtfoseulav
time and costs
SET: Input mode of
the time and cost of
electricidade
DISPLAY M/–:
Show the time, costs
or consumption
Presentation of various values of readings
OK: Save the intro / enter the price of
electricity and heat overload
Taken with integrated protection for
children. When inserting the plug should
fit into both pins simultaneously.
Area for indicating the voltage, current,
power, frequency, power factor and overload.
Area for indicating the hour operating time,
cost, power consumption, and money.
Graphical indication of the energy
consumption in the last 7 days.

16 17
Buttons
OK VALUE DISPLAY SET
Save introductions;
Choose 12 hours
or 24 hours
VRegular time
– A kWh
TOTAL –
Save introductions;
Show values AMAX
COST
kWh
Introduce
costs
of electric/kWh
– W COST
TOTAL –
– WMAX
TIME
TOTAL –
Save introductions AOVERLOAD
Introduce
limits of
overload
– Hz –
––
Overview of functions
E44395_Power meter_PT_IM_PRINT.indd 16-17
Press the button VALUE H/+ or DISPLAY M/-
to call the measurement values and particulars.
The settings can only be changed when the
corresponding values appear on the display (here
shown in grey). For this,Press the SET button for
3 seconds.

18 19
Preparation
Regular time
1.
2.
3.
4.
5.
.
6.
1.
Press the DISPLAY M / - until the display
appears .
2.
1.
COST kWh
2.
i
kWh
COST
E44395_Power meter_PT_IM_PRINT.indd 18-19
(no cost estimate) may skip this chapter
and proceed immediately to page 60.
Press the DISPLAY M/- until appears
Press the SET button for 3 seconds.
The hour indication flashes.
Set minutes with the VALUE H / +.
Adjust the minutes with DISPLAY M /-
Place the second zero-click
Complete and confirm the introduction with
the OK button.
Indication of 12/24 hours
Press the OK button to adjust 12 hours or
24 hours.(In case you choose the
indication of 24 hours, PM = after the
12:00).
Setting the price per kWh
Press the DISPLAY M / - until
the display shows
Keep the SET button pressed during 3
seconds. The Euro zone indication flashes

20 21
3.
4.
5.
6.
7.
8.
kWh
COST
kWh
COST
V
kWh
COST
E44395_Power meter_PT_IM_PRINT.indd 20-21
Now enter the price of electricity per
kilowatt-hour. If you have another price
for electricity at night first enter price
for the daily rate.
Adjust the value with the VALUE H/+
or DISPLAY M/- .
Press the SET button. The first
indication of the number of cents
Adjust the value in cents with the buttons
VALUE H+/ or DISPLAY M / - .
The following number of cents should
regulate itself in the same way
(example: 0285 = 28.5 cents).
Complete and confirm the input with the OK
button.
If you have a tariff of electricity
Normal (not bi-clockwise) then finished the
introduction of prices here and can move to
other menus with the DISPLAY M / -.

22 23
9.
10.
11.
12.
13.
V
kWh
COST
2
V
kWh
COST
2
V
kWh
COST
2
V
kWh
COST
2
E44395_Power meter_PT_IM_PRINT.indd 22-23
Introduction of the price for
energy at night
Press the OK button.
On the display appear 4 strokes. This means
that there is a second pricing for electricity at
night
Press the VALUE H / + to enter a price for
electricity at night. The display now as
follows:
Press the SET button for 3 seconds.
The area of the indication of reduced
blink rate
Set the price for electricity at night
conform the previously described
(3-7 points).
After the introduction of prices press the
OK button.The display shows now the
time display. Now enter the time from
which the electricity is accounted for by
more expensive price.

24 25
14.
15
16.
.
17.
18.
19.
20.
21
22.
V
TI ME
2
V
TI ME
2
V
TI ME
E44395_Power meter_PT_IM_PRINT.indd 24-25
Press the SET button for approximately 3
seconds. The time display is intermittent
try.
Set times with VALUE H/ +, and the
minutes with the DISPLAY M / -.
To save press the OK button.
Return to press the OK button to set the
time from which boasts the price of
electricity low (at night).
SET button pressed for about 3 seconds.
The hour indication flashes.
Enter the time from which the side will be
calculated in accordance with the price of
electricity in the evening (adjust the hours
with the VALUE H/+ and the minutes
with the DISPLAY M/-).
Save the entries by pressing the OK
With the OK button you can control the set
:otecneuqesnidetneserperaesehT.seulav
price day - price night - hours of daily rate
time of night tariff.
.
With the DISPLAY M / - then set another
value (eg hours)

26 27
Implementation of measurement
1.
2.
See the readings
•V(voltage)
•A(current a ctual)
•A MAX
(maximum current )
•W(absorbed power)
•WMAX
(maximum power absorbed)
•AOVERLOAD/ W
OVERLOAD(current value of overload
)
•Hz (Frequency )
•(power factor cos )
E44395_Power meter_PT_IM_PRINT.indd 26-27
After entering the time and price of electricity
could initiate measurements.
Only connect the appliance to an earthed
socket 230 V,which has been properly
installed.
Now connect (s) the consumer (s) or the
consumer (via a plug casing) to meter the
costs of electricity.
Note that the total power of consumers
connected must not exceed 3680 watts.
The following values are displayed:
power value of the overload

28 29
•(current time)
•kWh TOTAL (total consumption in kWh)
•kWh COST (price / kWh)
•COST TOTAL (price / kWh )
•TIME TOTAL (total time of measurement)
1.
2.
History of consumption
E44395_Power meter_PT_IM_PRINT.indd 28-29
To see long-term readings repeatedly press
DISPLAY M / - .
We present the following values：
derusaemseulavehteteleD
latotfoseulavehtraelcoslanacdeenfoesacnI
consumption (kWh), the time measuring total
and total costs, by pressing and holding the OK
button:
Press and hold VALUE H / + until Strom (A)
on the display.
Hold down the OK button until the device
.detelederaseulavllA.speeb
Its cost of the electricity meter stores the energy
consumption of the equipment connected over a
period of past 7 days.
The LCD display shows a graphical presentation
below, each column represents a day
(-1 = Yesterday, = -7 a week ago).
The individual bars in the columns represent the
kWh consumed.
According to consumption changes the scale,
so that each bar corresponds to 1, 2, 5, 10 or 15
kWh.

30 31
Overload
-
OVERLOAD
1.
OVERLOAD .
2.
3.
4.
5.
6.
7.
1.
2.
E44395_Power meter_PT_IM_PRINT.indd 30-31
Other functions (for professional)
Adjust the values of the overload
When one of the values of overload is ultra-past
appears on the display
blinking
and the device sends a beep.
Hold the button VALUE H/+ to
appear
on the display.
Hold down the SET button for
about 3 seconds.The display flashes to
indicate to the amps, or W for watts.
With the buttons VALUE H/+ or
DISPLAY M / -
Press again the SET button. The first digit in
the display flashes.
snottubehthtiwseulavderisedehtteS
VALUE H+/ or DISPLAY M / -.
With the SET button can go to the next digit
and regulate it the same way.
At the end confirm the introduction of
.nottubKOehthtiwseulav
daehrevofoseulavehteteleD
Press the VALUE H / + until Amax
(maximum current) and Wmax (maximum
power) on the display.
Hold down the OK button to the
provi-tive beeps. The value of the
corresponding on-load is then removed.
Power Factor
The power absorbed by a consumer in W is
calculated from the current in A multiplied by the
voltage V with the following formula:
P [W] = U [V] * I [A]
In the case of appearance of capacitive or
inductive consumer occurs, however,
With this function you can determine in
which current value (16 in max) or power:
5 WAT-cia (3680 W Max.) the appliance
shall issue a overload warning.

32 33
•
•
Troubleshooting
-
1.
2.
Cleaning
•
•
For cleaning use only a soft cloth
E44395_Power meter_PT_IM_PRINT.indd 32-33
gap between the course of current and voltage,
i.e. the current follows the course of the cur-so
the voltage or vice versa.With the phase angle φ
gets then the relationship between the effective
power, reactive power and apparent power.The
reactive power ensures that a coilor an electric
motor generates a field magnéti-co. The energy
of the reactive power is initially stored in the
magnetic field, but with each periodic magnetic
field reduction back to be sent to the network.
So, for the power we have then the following
formula, taking into account the actual values
U
e I:
p = U * I * cosφ – U * I * cos(2ωt+φ)
The expression contains a sum independent
of time, the active power P = U * I * cosφ,
A summation with temporal dual frequency
and amplitude S = U * I,
a variant whose average sum is zero.
The size S is called apparent power.
Indications not common in the visu-screen
Demoralization
If the display screen presents information not
common or if it does not react to touch the
buttons there should be an initiation device.
Remove the appliance.
Remove batteries briefly and then return to
place them as shown on page 33.
Caution: When removing the batteries, all
dnasgnittesyrotcafottesereraseulavdecud-ortni
have to be re-introduced later.
Danger of electric shock!
Always turn off the meter of the current cost of
electricity when cleaning it.
The system can not be washed or submerged in
liquid-Gido.

34 35
Disposal of used appliances
-
Packing
Environmental Protection
Disposal of batteries
E44395_Power meter_PT_IM_PRINT.indd 34-35
Cells and batteries can not be placed in
household waste!
Each consumer has a legal obligation to
deliver cells and batteries at a point
Collection of your community, your
neighborhood or in the store.
All batteries can be taken to a disposal
environmentally friendly.
Cells and batteries containing harmful
substances are marked by signs and by their
chemical symbols
(Cd as cadmium, Hg mercury, Pb for lead).
(Applicable in the European Union and other
European countries with separate collection of
recyclable materials)
The apparatus used should not be
placed in household waste! When
starting from a certain point no
longer able to use the device, each
consuming Pain has a legal obligation to
deliver separately used appliances, for
example, at a collection of community / your
neighborhood. Thus it is possible to ensure
that old appliances are properly utilized,
reducing in this way the negative impacts on
the environment.
This is why electrical appliances is
estab-tram marked with the symbol above.
Dispose of packaging materials that no longer
requires an appropriate and separate them
properly, giving them an appropriate collection
point.34 /35

36 37
Technical Data Accuracy of measurement
Volt : ± 3% of measurement
1) 2) 3)
Amperes : ± 3 % of measurement ± 0,002 A 1) 2) 3)
Watt : ± 3 % of measurement ± 1 W 1) 2) 3)
KWh : ± 3 % of measurement ± 0,1 kWh 1) 2) 3)
Factor :
± 0,1 % power factor measured
0,7 =< cos =< 1,0 2) 4)
Declaration of Conformity
E44395_Power meter_PT_IM_PRINT.indd 36-37
Input voltage / output voltage: 230 V ~ / 50 Hz
Power consumption: Max. 16
Range voltage: 190 V - 270 V
Current range: 0.01 A - A 19.999
Power range: 1 W - 3680 W
Indication of frequency: 46-65 Hz
Resolution: 0.5 W
Measurement of consumption: 0.00 to 9999.99
kWh
Duration of indication: up to 9,999 hours 59
minutes
Since our products are constantly updated and
improved technical changes are possible and
design.
1) Frequency: 46-65 Hz
2) Measurement in a normal room temperature
3) Distortion of voltage/current < 15%
4) Current > = 1.00A/sinusoidal.
Frequency = 50 or 60 Hz.
Without electronic circuits
We guarantee that the product in respect to
the standards required by law.

39
Warranty conditions
******Company**********
Phone number: 00800 / *************
Mai l : *****@**********
E44395_Power meter_PT_IM_PRINT.indd 38-39
ehthtiwedamsawuoyybdesahcruptcudorpehT
utmost care and subjected to continuous monitoring
during production.
The warranty period is 1 years and begins on the
date of acquisition.
If, despite the care processes of production and
verification, there is an abnormality in the unit, the
repair must be carried out by specialists.
In the case of any request for information or
replacement parts, always quote the model as the
signpost on the instrument.
Warranty service is provided in accordance with
statutory / country-specific (proof by invoice).
Excluded from the warranty service, the damage
that is caused by wear and tear, overloading
inappropriate or handling.In the event of a
complaint, first contact the customer support service.
This service will be glad to inform you with regard
to the following procedures. Please DO NOT send
your article unless it is required!
You should keep the receipt as proof of same.
This warranty does not apply in case of damage
caused by accident, improper handling and / or
force majure.
The warranty will be voided if unauthorized
nonoitalupinamfodnikynaedamevahsnosrep
the device.
In the case of sending the unit to our service, make
sure that the same be done in appropriate
packaging. We do not hold us accountable for any
damage caused by transportation. In case you need
our service guarantee, please go to our customer
support service: