Kleenmaid CustomStyle 23 User manual

Models 23 and 25
CustomStyleTM
For your nearest store call 13 13 08
www.kleenmaid.com.au
SPECIFICATIONS
Side-by-Side Fridge
GE Profile CustomStyleTM side by sides provide
a bold kitchen statement in stainless steel or
a flexible integrated option for blending the
refigerator with existing kitchen cabinetry styling.
Combined with all the convenience and food
preservation features necessary to make life
easier and extend your grocery investment, the
GE Profile side by side demonstrates leadership in
refrigeration technology.
Features:
Capacity: 720 litres
Temperature: ClimateKeeper2TM temperature management system
Dispenser: Water and Ice with upfront electronic temperature controls
Filtration: GESmartWaterTM filtration system
Shelves: Adjustable slide-out, SpillProofTM glass shelves
Colours: Stainless steel (PJE25PGTFSV)
Integrated trim (PJE25PGTFKB)
Dimensions: 909mm (W) x 1840mm (H) x 607mm (D)
pie23_pje25_specs.indd 1 17/9/08 11:37:36 AM

SPECIFICATIONS Models 23 and 25
CustomStyleTM
Side-by-Side Fridge
*Technical Specifications and product sizes can be varied by Manufacturer without notice. Any cut-outs for appliances should only be by physical measurements. Drawings are not to
scale. All information supplied is for general reference purposes only and is on the understanding that Kleenmaid Pty Ltd will not be liable for any loss, liability or damage whatsoever
arising as a result of reliance of such information.
Side-by-Side Fridge
Models 23 and 25
CustomStyle™
For your nearest store call 13 13 08
www.kleenmaid.com.au
EXCLUSIVE TO
BEFORE YOU BEGIN
*Installation of power and water outlets; if located in fridge cavity, please ensure they are above fridge height.
Instructions to your plumber: Install 1/2 inch stop cock (tap), located in the cabinetry or adjacent to, or if possible above fridge cavity. Not to be
located in the fridge cavity.
The water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these recommendations carefully to minimise the
risk of expensive water damage.
Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call
a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook up the water line to the hot water line.
If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position.
Do not install the icemaker tubing in areas where temperatures fall below freezing.
When using any electrical device (such as a power drill) during installation, be sure the device is insulated or wired in a
manner to prevent the hazard of electric shock.
All installations must be in accordance with local plumbing code requirements. Installation of the icemaker must be done by a qualified service
technician.
! WARNING! Connect to potable water supply only.
INSTALLING THE WATER LINE
DIMENSIONS AND SPECIFICATIONS (for CustomStyle™ and installed trim models)
CM
#ABINET
7ATER %LECTRICAL
MM!IRSPACE
MM'APMM
7ALL0LATES CM
#OUNTERTOP
/ÊLiÊViVÌi`Ê>LÛiÊvÀ`}iÊi}Ì
Dimensions
PIE23 PJE25
A- Height to top of Hinge 1759 mm 1832 mm
B- Height to top of case 1747 mm 1817 mm
Height to top of door trim 1785 mm 1840 mm
C- Case depth without door 607 mm 607 mm
D- Case depth without
door handle 680 mm 689 mm
E- Case depth with door
handle 720 mm 751 mm
F- Depth w/FF door open 90° 1158 mm 1169 mm
G-Width 908 mm 909 mm
H-Width w/door open 90°
w/door handle 1016 mm 970 mm
Air Clearances
Allow the following clearances from cabinet for ease of
installation, proper air circulation and plumbing and
electrical connections:
Sides 4 mm 4 mm
Top 25 mm 25 mm
Back 13 mm 25mm
A B
CDE
F
G
H
PIE23_PJE23_specs.indd 1 14/2/08 11:24:32 AM
pie23_pje25_specs.indd 2 17/9/08 11:37:38 AM

SPECIFICATIONS Models 23 and 25
CustomStyleTM
Side-by-Side Fridge
Side-by-Side Fridge
Models 23 and 25
CustomStyle™
For your nearest store call 13 13 08
www.kleenmaid.com.au
EXCLUSIVE TO
2EATTACHTHEACCESSCOVER
4YPICAL
#OMPRESSION
.UT
4UBING
#LAMP 4UBING
&ERRULE
SLEEVE
2EFRIGERATOR
#ONNECTION
4UBING
4UBING#LAMP
4YPICAL
#OMPRESSION.UT
&ERRULE
SLEEVE
2EFRIGERATOR#ONNECTION
0OWER
SWITCH
CONNECT THE TUBING TO THE REFRIGERATOR
NOTES:
• Before making the connection to the refrigerator, be sure the refrigerator power
cord is not plugged into the wall outlet.
• We recommend installing a water filter if your water supply has sand or particles
that could clog the screen of the refrigerators water valve. Install it in the water
line near the refrigerator. Some models have the refrigerator connection at the
end of tubing located outside the compressor compartment access cover. On
other models the compressor compartment access cover must be removed in
order to access the refrigerator connection at the water valve.
On models using the refrigeration connection at the water valve,
remove the plastic flexible cap.
Place the compression nut and ferrule (sleeve) onto the end of the tubing as
shown.
Insert the end of the tubing into the water valve connection as far as
possible. While holding the tubing, tighten the fitting.
Fasten the tubing into the clamp provided to hold it in a vertical position.
You may need to pry open the clamp.
One of the illustrations adjacent will look like the connection on your
icemaker.
Reattach the access cover.
TURN THE WATER ON AND PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate against the back of the
refrigerator or against the wall. Push the refrigerator back to the wall. Adjustable
ROLLERS are fitted with all GE refrigerators, these enable the fridge doors to be
aligned and ensure the refrigerator is firmly positioned on the floor, also allowing
the fridge to be moved away from the wall for cleaning. Final adjustments of your
fridge will be completed by your qualified Kleenmaid Installer.
START THE ICEMAKER
Set the icemaker power switch to the l position. The icemaker will not begin to
operate until it reaches its operating temperature of -9°C or below. It will then
begin operation automatically if the icemaker power switch is in the / position.
NOTE: In lower water pressure conditions, the water valve may turn on up to 3
times to deliver enough water to the icemaker.
INSTALLING THE WATER LINE
PIE23_PJE23_specs.indd 2 14/2/08 11:24:34 AM
pie23_pje25_specs.indd 3 17/9/08 11:37:41 AM

SPECIFICATIONS Models 23 and 25
CustomStyleTM
Side-by-Side Fridge
Side-by-Side Fridge
Models 23 and 25
CustomStyle™
For your nearest store call 13 13 08
www.kleenmaid.com.au
EXCLUSIVE TO
or glass
For glass/mirror panels, we recommend a maximum thickness of 4mm toughened glass with
cardboard packaging.
GLASS / MIRROR / SOLID WOOD PANELS
Important Note on Installation – Please Read:
• We recommend a maximum thickness for toughened glass / mirror / solid wood
panels to be 4mm
• When installing panels less than 6mm thick you need to create a filler panel such
as very thin cardboard that will fit between the face of the door and the panel
• The filler panel may need to be either one piece or as required to prevent
movement and stabilize the decorator panel
• If you are installing the pre-cut decorator panels, pre-cut filler panels are included
in the kit
PIE23_PJE23_specs.indd 3 14/2/08 11:24:37 AM
pie23_pje25_specs.indd 4 17/9/08 11:37:44 AM

SPECIFICATIONS Models 23 and 25
CustomStyleTM
Side-by-Side Fridge
Side-by-Side Fridge
Models 23 and 25
CustomStyle™
For your nearest store call 13 13 08
www.kleenmaid.com.au
EXCLUSIVE TO
4RIMKITS
$IMENSIONSFOR#USTOM7OOD0ANELS
Dimensions for Custom Panels
A
B
C
3 mm
Cutout
3 mm
Cutout
Mirror / decorative panels
Mirror and decorative panel dimensions (in mm)
A B C
Models H W H W H W
23' Installed trim model 454 368 854 368 1709 495
25' Installed trim model 432 368 920 368 1753 495
Weight limitations for custom panels
Refrigerator door 17 kg max.
Freezer door 13 kg max.
8mm 8mm
PIE23_PJE23_specs.indd 4 14/2/08 11:24:40 AM
pie23_pje25_specs.indd 5 17/9/08 11:37:47 AM

SPECIFICATIONS Models 23 and 25
CustomStyleTM
Side-by-Side Fridge
Side-by-Side Fridge
Models 23 and 25
CustomStyle™
For your nearest store call 13 13 08
www.kleenmaid.com.au
EXCLUSIVE TO
ÄjÁÍ~ËÍjËaÁˬ?jı
-j?aËÍjÄjËÄÍÁÖWÍÄËW¬jÍjßË?aËW?ÁjwÖß±
ÍÍ?WËÍjË0¬Ë0ÁËËÍjËÁjjãjÁË?aËÁjÄËaËÁı
0jË0¬Ë0ÁËW?ËMjËwÖaËÄajËÍjËÁjwÁ~jÁ?ÍÁ
W¬?ÁÍjͱ
8ÍË?Ë0ÔåË0ÁÞaÁÜjÁ^Ë?ÍÍ?WËÍjË0¬Ë0Á^ËÖÄ~
ÍÝËÄWÁjÝÄËËj?WË0¬Ë0ÁˬjWj^ËÍËÍjËÍ¬Ëw
j?WËaÁ±Ë?aËÍ~ÍjËß±Ë ?jËÄÖÁjËÍ?ÍËÍj
Í¬ËwËj?Wˬ?jËwÍÄËÄÖ~ßËMjaËÍjË¬ËwËÍj
0¬Ë0Á±
ÄjÁÍËÍjËÁjjãjÁË+?jË?aËÁjÄËaË+?j±
?ÁjwÖßˬÖÄËÍjËÍ¬ËwÁjjãjÁˬ?jËËÖÍËÍËÄajÄ
ÍËÍjËÄÍËMjaËÍjËaÁË?aj±Ë+ÖÄËÍjËwjÁ
¬?jË®Áj¶ÖÁjaËÝÍËÄjËaÁˬ?jįËËMja
ÍjËajWÁ?ÍÁˬ?j±Ë-j¬j?ÍËwÁËwÁjÄËwaˬ?j±
ÄjÁÍËÍjËÍÍËÁjjãjÁË+?j±
?ÁjwÖßˬÖÄËÍjˬ?jËËÖÍËÍËÄajÄËÍËÍj
ÄÍËMjaËÍjËaÁË?aj±Ë+ÖÄËÍjËwjÁˬ?j
®Áj¶ÖÁjaËÝÍËÄjËaÁˬ?jįËËMjaËÍj
ajWÁ?ÍÁˬ?j±
ÖÍ#ÖÍ
ÖÍ#ÖÍ
0¬Ë0ÁË.WÁjÝÄ
0¬
ÁjjãjÁ
+?j
ÍÍ
ÁjjãjÁ
+?j
.ajË0Á
.ajË0Á
ÁjÄ
a
+?j
0¬Ë0ÁË.WÁjÝÄ
PIE23_PJE23_specs.indd 5 14/2/08 11:24:42 AM
pie23_pje25_specs.indd 6 17/9/08 11:37:49 AM

SPECIFICATIONS Models 23 and 25
CustomStyleTM
Side-by-Side Fridge
Side-by-Side Fridge
Models 23 and 25
CustomStyle™
For your nearest store call 13 13 08
www.kleenmaid.com.au
EXCLUSIVE TO
)NSERTINGTHEDOORPANELS
)NSTALLTHE3IDE4RIM
4HESEPIECESARETUCKEDINSIDETHEREFRIGERATORDOOR
HANDLE
$ONOTREMOVETHEPROTECTIVEFILMONTHEOUTSIDEOFTHE
3IDE4RIMUNTILTHE3IDE4RIMISINSTALLED
&ITTHEBOTTOMOFTHE3IDE4RIMUNDERTHE"OTTOM
4RIMASILLUSTRATED
(OLDTHE3IDE4RIMAGAINSTTHEFRONTFACEOFTHE
DECORATORPANELSANDFITTHE3IDE4RIMUNDER
THE4OP4RIM-AKESURETHEMAGNETICALLYATTACHED
3IDE4RIMISFITTEDCORRECTLYANDTHATYOUARE
SATISFIEDWITHTHEAPPEARANCEOFALLTHEPARTS
3IDE
4RIM
3IDE
4RIM
"OTTOM4RIM
4OP4RIM
PIE23_PJE23_specs.indd 6 14/2/08 11:24:45 AM
pie23_pje25_specs.indd 7 17/9/08 11:37:52 AM