KLEVA MEALiO User manual

Please read the Instructions Guide carefully before use
& Keep User Manual for future guidance
USER MANUAL
The Hot and Cold Nutritional Blender
TM
www.klevarange.com.au
RECIPES
FOR A VARIETY OF
SUITED FOR
Please visit our website at
The Hot and Cold Nutritional Blender
TM


READ THIS IMPORTANT INFORMATION CAREFULLY BEFORE
YOU USE THE APPLIANCE AND SAVE IT FOR FUTURE REFERENCE
Do not misuse the appliance to avoid potential injury.
This appliance is intended to be used in household only.
Do not touch the sharp blades when the appliance is plugged in.
If the blades get stuck, unplug the appliance before you remove the ingredients.
Be careful when handling the sharp cutting blades, emptying the bowl and during cleaning.
Switch o and unplug the appliance from the power supply before :
*Removing it from the stand, changing accessories or approaching parts that move in use.
*Assembling, disassembling or cleaning it.
*It is left unattended.
Do not immerse the appliance in water or any other liquid.
Check if the voltage indicated on the appliance corresponds to the local mains voltage before
you connect the appliance.
Do not use the appliance if the plug, the power cord, lid, or blender jar are damaged or
has visible cracks. If the power cord is damaged, you must have it replaced by Kleva Range®,
a service centre authorised by Kleva Range® or similarly qualified persons in order to avoid a hazard.
Make sure the lid is properly assembled to the Blender Jar before you use the appliance.
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and if they understand the hazards involved.
Children should be supervised to ensure that they do not play with the appliance.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance
must not be supplied through an external switching device, such as a timer, or connected to a
circuit that is regularly switched on and o by the utility.
Be careful if hot liquid is poured into the Blender Jar as it can be ejected out of the appliance
due to a sudden steaming.
Never assemble or disassemble the Blender Jar to the motor base while the power is on.
Read the ‘User Manual’ before use.
Be careful that the heating element surface is subject to residual heat after use.
WARNINGS


WARNINGS
Never use any accessories or parts from other manufacturers or that Kleva Range® does not
specifically recommend. If you use such accessories or parts, your guarantee becomes invalid.
Only connect the appliance to an earthed wall socket.
Do not exceed the maximum indication on the Blender Jar.
Do not exceed the maximum quantities and processing times indicated in the relevant table.
If food sticks to the wall of the Blender Jar, switch o the appliance and unplug it.
Then use a spatula to remove the food from the wall.
Never fill the Blender Jar with ingredients hotter than ambient temperature. Avoid to pour cold
water into the blade unit and Blender Jar immediately after use. Wait until it has been fully cooled.
The appliance can only be switched on if the Blender Jar is assembled on the motor base correctly.
Do not touch the heating element and blade after use.
Let it cool down for approx 30 minutes before cleaning or disassembly.
Do not use the Blender for more than 6 minutes at a time. Stop using for 1 minute after blending,
only blend 3 times in 6 minute intervals then unplug the appliance and let cool for 15 minutes
before using again.
Do not cook with the appliance for more than 50 minutes. If the Blender powers o during
cooking, unplug it and change the ingredients before starting again.
www.klevarange.com.au
RECIPES
FOR A VARIETY OF
SUITED FOR
Please visit our website at
The Hot and Cold Nutritional Blender


HOW TO ASSEMBLE
Removable Centre Cap
Blender Lid
Blender Jar
Driving Shaft Head
Motor Base
Control Panel
Selector Wheel
1.
2.
3.
4.
5.
6.
7.


IMPORTANT: REVIEW ALL WARNINGS ON PAGES  BEFORE PROCEEDING
Assembling the Appliance
1. Plug in Motor Base and place on a clean,
dry level surface such as a countertop or table.
2.Lower the Blender Jar onto the motor base.
3. Add ingredients, making sure to not exceed
the max fill lines on side of Blender Jar.
In COOK mode, DO NOT exceed the level
labelled “SOUP” in BLEND mode,
DO NOT exceed the level labeled “COLD”.
4. To install the lid on the Blender Jar, place the
Blender Lid tab to the right of the handle.
Press the Lid down until it is secure. Rotate Lid
clockwise so the Lid tab and the handle tab are
aligned.
5. Secure the Centre Cap by placing it down in
to the Lid and twisting clockwise until it clicks
in to place.
6. To remove the Lid from the Blender Jar,
rotate Lid counter clockwise out of the lock
potions and lift up.
NOTE: After heated programs, steam may
release as the Lid is removed. Keep hands on
the outer tabs and lift directly up.
HOW TO USE
Cold Line
(1200mL)
Soup Line
(800mL)


Pre-set
The Pre-Set time function is only available for the 4 hot blending and cooking programs
which include Soy Milk, Soup, Thick Soup and Paste Function. (View our Kleva Range®
website to see more Hot Recipes)
Step 1 - Following your chosen recipe add the ingredients into the Jug and lock and secure the lid into place.
The ON/OFF button will now start to flash and the selector wheel will appear to have no numbers and show
as (-- --). (E01 will appear if the lid is not properly secured or aligned with handle. The lid not being locked in
will cause the Mealio™ to not function which is a safety feature).
Step 2 - Select/touch the ON/OFF button and you will see that the flashing has disappeared and the 8 Pre
Set Programs and the touch control panel will light up. The Selector Wheel Screen will now appear to have the
numbers 00:00 in the first row and 0 on the second row.
Step 3 - Select the function you would like to use by turning the selector wheel clock wise. Once the function
is selected you will now see that the chosen function Icon has begun to flash along with the Pre Set Button.
Step 4 - Now select/touch the Pre-Set Button and the flashing will now stop and you are now ready to choose
how long you would like it to start cooking from your present time. To adjust the time you are to turn the
selector wheel in a clock wise direction to increase the time by 10min and anti-clock to reduce the time by 10
min. The pre-set time ranges from 10min to 12 hours and you can only increase or decrease the time by 10 min.
Step 5 - Once you have selected your pre-set time you are to now to select/touch the ON/OFF start button
and this will start a countdown display process. When the countdown is completed and it has now reached
your chosen Pre-Set time it will start to heat up and cook the ingredients/meal.
Note: Press the ON/OFF button to directly stop the appliance during countdown or operation.
Note: If E01, E03, E04 or E05 appears to be displayed you on your selector wheel screen during your
cooking process at any time please DO NOT panic and go to PAGE 16 for more information on what these
safety errors mean.
INGREDIENTS WARNING: Please ensure that all wet ingredients such as the liquids (cream and water) is to
go in first , then is to be followed by any other dry ingredients at the top such as (beans, potato’s and
legumes). Any spices, stock cubes and powdery substances is to be added into the Mealio™ last to avoid any
of these products sticking to the base of the Mealio™ Jar. Please make sure that the produce and liquid is
cold/raw to prevent the Mealio™ from overheating (RAW MEAT IS NOT TO BE ADDED INTO THE MEALIO™). If
you are adding pre-cooked ingredients please make sure it has completely cooled down and is cold before
PROGRAMS
TOP CONTROL PANEL INSTRUCTIONS


Pulse Setting
The Pulse Function can only be used for Cold Blending and NOT for Hot/Heated
blending. The Pulse function will automatically be set on the Fastest/ Highest blending
setting which is 9 and can run for a maximum of 1 minute blending at a time. The Pulse
function is great feature which allows you to control what you are mixing/cooking with,
giving you that perfect consistency and texture that you are looking for and can also be
used to breakdown ingredients before selecting another pre-set program.
Step 1 - Once your contents are in the Jug you are to lock and secure the lid into place. The ON/OFF button
will now start to flash and the selector wheel will appear to have no numbers and show as (-- --). (E01 will
appear if the lid is not properly secured or aligned with handle. The lid not being locked in will cause the
Mealio™ to not function which is a safety feature).
Step 2 - Select/Touch the ON/OFF button and you will see that the flashing has disappeared and the 8 Pre
Set Programs and the touch control panel will light up. The Selector Wheel Screen will now appear to have the
numbers 00:00 in the first row and 0 on the second row.
Step 3 - For the Mealio™ to start Pulsing you are to touch and hold your finger on the Pulse button and you will
start to see that the ingredients in the jar blend. Removing your finger away from the Pulse button will stop the
Mealio™ from pulsing. Please keep in mind that the touch control panel is touched base.
Step 4 - Once you select the Pulse Function it will automatically start pulsing and the selector wheel screen
will have the number numbers counting down from 60 seconds in the first row and the second row will the
number 9 which is the level of speed.
Note: If E01, E03, E04 or E05 appears to be displayed you on your selector wheel screen during your
cooking process at any time please DO NOT panic and go to PAGE 16 for more information on what these
safety errors mean.
INGREDIENTS WARNING: Please ensure that all wet ingredients such as the liquids (cream and water) is to
go in first , then is to be followed by any other dry ingredients at the top such as (beans, potato’s and
legumes). Any spices, stock cubes and powdery substances is to be added into the Mealio™ last to avoid any
of these products sticking to the base of the Mealio™ Jar. Please make sure that the produce and liquid is
cold/raw to prevent the Mealio™ from overheating (RAW MEAT IS NOT TO BE ADDED INTO THE MEALIO™). If
you are adding pre-cooked ingredients please make sure it has completely cooled down and is cold before
PROGRAMS


DIY Time/Speed Program
The DIY function manually allows you to set a chosen blending time and speed for Cold
Blending only and can NOT be used for hot and heated blending. The Blending time you
can choose from ranges from 5 seconds to 3 minutes and you can choose a speed
setting from 1 being the lowest to 9 being the fastest. The lowest speed function 1 is
great for blending things such as soft ingredients and the lowest speed function 9 would
be recommend for blending things such hard raw vegetables and frozen food product.
Step 1 - Once your contents are in the Jug you are to lock and secure the lid into place. The ON/OFF button
will now start to flash and the selector wheel will appear to have no numbers and show as (-- --). (E01 will
appear if the lid is not properly secured or aligned with handle. The lid not being locked in will cause the
Mealio™ to not function which is a safety feature).
Step 2 - Select/Touch the ON/OFF button and you will see that the flashing has disappeared and the 8 Pre
Set Programs and the touch control panel will light up. The Selector Wheel Screen will now appear to have the
numbers 00:00 in the first row and 0 on the second row.
Step 3 - Select/Touch the DIY button once. You will now see the Selector Wheel Screen appear to have
numbers in two rows (00:30 in the first row and 1 on the second row). The First Row of numbers shown is the
time and this will be flashing the number 00:30 and the DIY setting Icon will also be flashing. You are now to
choose the time, turn the Selector Wheel in a clockwise direction to increase the time to anything to up to 3
minutes and anti-clockwise to decrease the time to the lowest being 5 seconds. Once chosen time is selected
stop turning the wheel and select/touch the DIY Function Icon once and the second row will start to flash.
Step 4 - The second row of numbers on the Selector Wheel Screen will appear to flash along with the DIY
Icon. The second row with the flashing singular number allows you to control the speed. Turn the wheel
clockwise to increase to the speed and anti-clockwise to decrease the speed. You can choose from any speed
levels between 1 to 9, 1 is the lowest blending speed and 9 is the highest blending speed.
Step 5 - The speed has now been selected so you are to now select/touch the ON/OFF start button and once
you select the on button the Mealio™ will start blending with your chosen speed and blending time. The
Selector Wheel Screen will also show a countdown of your selected blending time.
Note: If E01, E03, E04 or E05 appears to be displayed you on your selector wheel screen during
your cooking process at any time please DO NOT panic and go to PAGE 16 for more information
on what these safety errors mean.
INGREDIENTS WARNING: Please ensure that all wet ingredients such as the liquids (cream and water) is to
go in first , then is to be followed by any other dry ingredients at the top such as (beans, potato’s and
legumes). Any spices, stock cubes and powdery substances is to be added into the Mealio™ last to avoid any
of these products sticking to the base of the Mealio™ Jar. Please make sure that the produce and liquid is
cold/raw to prevent the Mealio™ from overheating (RAW MEAT IS NOT TO BE ADDED INTO THE MEALIO™). If
you are adding pre-cooked ingredients please make sure it has completely cooled down and is cold before
DIY
PROGRAMS


On/O
ON/OFF Button Turn on Appliance. Start and Stop Programs. Awaken from Sleep Mode
When the appliance has been connected to power the ‘ON/OFF’ Button will light up, press the button to turn on.
When the lid is on the Blender, it will enter Standby Mode and the entire control panel will light up.
Use the ‘ON/OFF’ button to start a selected program or immediately stop the Blender during operation.
If the appliance is connected to power with no setting selected within 5 minutes, it will enter Sleeping Mode.
Use the ‘ON/OFF’ button to awaken the Blender and use.
PROGRAMS
E01 is a safety feature that is designed to notify you that the lid is not securely attached. The Mealio™ will not
function if the Lid is not secure. The Mealio™ has a magnetic sensor design which requires the blender sensor
on the lid to be locked into place and be in alignment with the Mealio™ jar handle sensor.
HOW TO ATTACH LID
Please refer to The Next Page of the instruction
Manual for HOT BLENDING PRESETS.
Step 3 - Turn the lid
clockwise until it cannot
turn anymore. Making sure
to line up the lip of the lid
with the jar
Step 2 - Push the Mealio™
lid into the Mealio™ Jar
Step 1 - Once the Mealio™ motor
base is plugged in, you are to place
the Mealio™ Jug on top. Once the
jug is in the motor base an Error
sign will appear on the selector
wheel screen which is E01.