manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. KLIK
  6. •
  7. Landscape Lighting
  8. •
  9. KLIK LEDpod 50 User manual

KLIK LEDpod 50 User manual

NEGATIVE [ - ]: Black
POSITIVE [ + ]: Red
90°
The notch indicates
the direction of the light,
Asymmetrical LEDPods
Light
direction
Insert removal tool into the
2mm holes in the LEDPOD.
With firm pressure, rotate
the LEDPod 90°.
Carefully peel back
the IP silicone seal
one side at a time.
Carefully remove the LEDPOD
from the clip, ensuring not to
damage or disconnect wires in
the process.
Be sure to re-attach
the silicone seal ready
for reinsertion.
Push LEDPOD in until it snaps into place
and the outer surface is flush with the outer
surface of the tube.
Prod the rim of the clear silicone IP Seal to
provide a tighter fit.
9
1 2 3
LEDPOD Removal Steps
Thru.
wire
PAGE 1 OF 2
Pull a loop of wire through hole. Rotate retaining clips in as shown. Avoid
tangling or severing through wire.
3 4 5
Apply pressure as shown to deform clip into place in a
circular motion. Avoid damaging the surface of tube
and tangling or severing through wire.
Install Scotchlok connectors to the (0.75-1.5sq) red
and black wires. Connect the corresponding color
wires of the driver to the Scotchloks and assure the
clip is secured.
CAREFULLY feed the Scotchloks to the left of
the clip and the driver to the right with the
driver connector hanging out. Ensure wires
are clear from where the LEDPOD is to fit.
Proceed to connect the LEDPOD.
6 7 8
Fit clip into place until the clamping
ends are equally centered over the
hole. Use the tool to center the clasp
until equal pressure can be felt and
inspect by eye.
Feed through appropriate
wires (0.75-1.5mm²).
2
Make sure drilled holes are
deburred and excess swarf
is removed from railing.
1
32864-C.1
www.klikusa.com - [email protected]
Ø 0.96”
Ø 1.02”
1.34”
OD 1.75”
2.38”
Ø 25 ± 0.2mm
Use a 25mm annular cutter
to bore hole.
(Use 1” in aluminum.)
Aprx 2”
KLIK LEDpod™ 50 Installation Instructions
www.klikusa.com - [email protected]
Match colors of wires as shown in the images below.
Insert wires into connectors as far as possible and push down blue tabs to splice the wires.
IMPORTANT : Connect to 24 - 42V DC supply input to the Blue and Red Soft starter
DO NOT connect power to any other wires.
Blue IN
Negative [-]
Red IN
Positive [+]
Black OUT
Negative [-]
Red OUT
Positive [+]
23
5
4
24 - 42V DC IN Black
Negative [-]
24 - 42V DC IN Red
Positive [+]
LEDPOD OUT
Black Negative [-]
LEDPOD OUT
Red Positive [+]
Cut wires at the center
of the loop.
24VDC Supply
INPUT
To LEDPods
OUTPUT
Carefully feed one
connector at a time
through the
LEDPOD holes.
Carefully pull out a
loop of wire at the
first LEDPOD location.
Feed power wires
through tubing
Soft starter complete
with pre-fitted connectors
1
To 24V DC Supply
INPUT
To LEDPODs
OUTPUT
Move components down to make room for retaining clip insertion.
Refer to page 1 for LEDPOD installation instructions.
6
PAGE 2 OF 2 32864-C.1
Aprx 2”
KLIK LEDpod™ Soft Start Relay Installation Instructions

Popular Landscape Lighting manuals by other brands

LIGMAN ALDO 4 installation manual

LIGMAN

LIGMAN ALDO 4 installation manual

Intex SL1006 owner's manual

Intex

Intex SL1006 owner's manual

LED Group ROBUS R2IN13W quick start guide

LED Group

LED Group ROBUS R2IN13W quick start guide

Patriot Lighting 343-1484 installation manual

Patriot Lighting

Patriot Lighting 343-1484 installation manual

LIGMAN JET 44 installation manual

LIGMAN

LIGMAN JET 44 installation manual

Hess SERA G: SERA S Installation and operating instructions

Hess

Hess SERA G: SERA S Installation and operating instructions

LIGMAN MALTA 1 installation manual

LIGMAN

LIGMAN MALTA 1 installation manual

Saxby Lighting Islay 68784 Instruction leaflet

Saxby Lighting

Saxby Lighting Islay 68784 Instruction leaflet

LIGMAN EU-10016-3 installation manual

LIGMAN

LIGMAN EU-10016-3 installation manual

LIGMAN KI-60475 installation manual

LIGMAN

LIGMAN KI-60475 installation manual

Cooper Lighting McGraw-Edison ZD Credenza specification

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza specification

Cooper Lighting Generation CLB25MWW5C373 Specification sheet

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Specification sheet

Malibu Boats CM110P instructions

Malibu Boats

Malibu Boats CM110P instructions

AMP Lighting OrchardPro APL-3018-B-BZ Installation & maintenance guide

AMP Lighting

AMP Lighting OrchardPro APL-3018-B-BZ Installation & maintenance guide

Cooper Lighting Invue 42 - 175W Specification sheet

Cooper Lighting

Cooper Lighting Invue 42 - 175W Specification sheet

ABBA SPB12 installation guide

ABBA

ABBA SPB12 installation guide

Techmar Garden Lights GILVUS + manual

Techmar

Techmar Garden Lights GILVUS + manual

LIGMAN RADO 1 installation manual

LIGMAN

LIGMAN RADO 1 installation manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.