Klipsch IC-400-T User manual

KLIPSCH PROFESSIONAL
IN-CEILING LOUDSPEAKERS
IC-400-T I IC-500-T-SC I IC-525-T I IC-650-T I IC-800-T
OWNER'S MANUAL
Klipscl1

IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth or lightly damped cloth.
7. DO NOT block any ventilation openings. Install in accordance
with the manufacturer's instructions.
8. DO NOT install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers)
that produce heat.
9. ONLY USE attachments/accessories specifically designed
for this application
10. USE only with a cart, stand, tripod, bracket, or table specifically a
designed for this application, or sold with the apparatus. When \CW
a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
11. DO NOT expose this apparatus to dripping or splashing and ensure that
no objects filled with liquids, such as vases, are placed on
the apparatus.
12. DO NOT modify or alter in any way.
13. SWITCH OFF amplifier prior to connecting speakers.
14. DO NOT hang or suspend any items from this apparatus.
A The exclamation point, within an equilateral triangle, is intended to
~ alert the user to the presence of important operating and mainte-
nance (servicing) instructions in the literature accompanying the product.
A The lightning flash with arrowhead symbol within an equilateral
..... triangle is intended to alert the user to the presence of uninsu-
lated "dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock to persons.
WARNING: To reduce the risk of fire or electrical shock, do not expose
this apparatus to rain or moisture.
WARNING: No naked flame sources - such as candles - should be
placed on the product.
WARNING: The apparatus is not designed to be used for any type of
moving or lifting installation.
WARNING: For Indoor use only.
WARNING: Installation must be done by qualified personnel to
appropriate standards and/or building codes.

WARNING: Neglect to follow the safety and
installation instructions may cause malfunctions
resulting in property damage and personal injury.
A A
AVIS. RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
WARNING: Do Not Open! Risk of Electrical Shock.
Voltages in this equipment are hazardous to
life. No user-serviceable parts inside. Refer all
servicing to qualified service personnel.
Klipsch recommends that only qualified personnel install its
loudspeaker systems. At all times, be sure that adequate
safety factors are observed. Due to the weight and size of the
components involved, potential damage could occur if devices
were to become unattached.
The included tile-bridge must be used when installing into
suspended ceilings. Use the seismic tab as a secondary means of
support. In some areas, using the seismic tab is required by code.
FR - Manuel en Fran~ais: KLIPSCH.COM/PRO/IC·SERIES·MANUAL
SP- Manual en Espanol: KLIPSCH.COM/PRO/IC-SERIES·MANUAL
GR - Handbuch in Deutsch: KLIPSCH.COM/PRO/IC·SERIES·MANUAL
PR· Manual em Portugues: KLIPSCH.COM/PRO/IC·SERIES·MANUAL
IT· Manuale in Italiano: KLIPSCH.COM/PRO/IC-SERIES·MANUAL
SC· i:p)tifffl~ffl} ( i:fll): KLIPSCH.COM/PRO/IC·SERIES·MANUAL

KLIPSCH PROFESSIONAL IN-CEILING SPEAKERS
IC-400-T
. ..
(
,
l
I•
.. .
IC-800-T
IC-500-T-SC
IC-650-T
CONTENTS
x2 Speaker Modules
x2 Grilles
x2 Reinforcement Rings
x4
Rails
x2
Cardboard Cutout Template and Paint Mask
x8 Screws (Attach Rails to Reinforcement Ri ng)
x2 3/4" Adapter fittings
xl Speaker Module xl Cardboard Cutout Template
xl
and Paint Mask
Grille
x4 Screws (Attach Rails to Reinforcement Ring)
xl Reinforcement Ring
xl 3/4" Adapter fitting
X2 Rails

INSTALLATION
All Klipsch Professional In-Ceiling
speakers include a tilebridge for use
when installing the loudspeaker into
suspended ceiling or wherever additional
reinforcement of the ceiling material is
required. The tilebridge and loudspeaker
are designed such that installation may
be accomplished where access above the
ceiling is not possible or may be difficult.
The tilebridge is composed of three
~fl
I I
I I
I I
I I
I I
I I
I I
I I
I I
I I
parts: a reinforcement ring and two rails.
The two rails should be attached to the
reinforcement ring using the four included
screws as shown
BE SURE TO COMPLY WITH
ANY AND ALL BUILDING
CODES IN YOUR AREA

INSTALLATION
-
TEMPLATE
=:,
To install your speaker cut a hole in the ceiling
using either the cardboard cutout template
provided with your speakers or consult the
measurements shown. Pull wiring through hole.
.,,,.
/
I
,
\
\ ' '
IC-4OO-T, IC-525-T, IC-5OO-T
IC-65O-T
IC-8OO-T
-- .....
'
'\
\.
/
---
09.125"
010.125"
012.625"

To Install the tilebridge, fold the rail side of the ring back upon itself using the spring tensioner on
the reinforcement ring to allow insertion into the cutout hole. Once it is inserted into the cutout
hole, release the reinforcement ring such that it unfolds back to its normal position. Position
tilebridge over cutout hole, and insure that the tile rails rest on the t-grid struts.

INSTALLATION
+ +
70/100v Common 8 ohm
The wiring compartment is intended as a termination point for the audio circuit.
Access to the compartment is gained by removing the terminal cover located
on the back of the speaker. (For the IC-500-T-SC, the terminal is located on the
side of the speaker) The terminal cover will accept the appropriate conduit/wire
adapter. Feed wires through conduit/wire adapter and connect to the input terminal
according to the desired operation mode. Be sure to observe proper polarity. .
Replace the terminal cover and tighten the conduit/wire adapter to secure the wire.
FOR IC-500-T·SC ONLY
WHEN CONNECTING 70V OR 100V
If\ DISTRIBUTED LINE SYSTEMS, TAKE CARE TO
LD ENSURE PROPER TERMINAL CONNECTION.
CONNECTION TO THE LOW IMPEDANCE
TERMINAL COULD RESULT IN SPEAKER
DAMAGE, AMPLIFIER DAMAGE, OR BOTH.

Insert the speaker into the cutout hole. With a #2 Phillips screwdriver, tighten the four
dog clamps until they are seated securely against the ceiling surface. Do not overtighten.
[

INSTALLATION
For installations using 7OV/1OOV
input connection, set the switch
on the front panel to the desired
setting. For applications where
8 Ohm impedance is desired, the
switch should be set to 8 Ohms
(or 6.5/7.5 ohm for the IC-8OO-T/
IC-65O-T).
Note: The speaker comes from the
factory set at the lowest output
setting (high impedance).
IC-4OO-T tap selectable
IC-5OO-T-SC tap selectable
IC-525-T tap selectable
IC-8OO-T tap selectable
IC-65O-T tap selectable