Klugmann KT905X User manual

KT905X
Cooktop
INSTRUCTION MANUAL
Klugmann Hausgeraete GmbH.
Gropiusstraße 7,
48163 Münster, Deutschland
+49 (0)2501 - 963 5732
+49 (0)2501 - 963 1834
[e-mail]
www.klugmann-hausgeraete.de

Introduction
We thank you for choosing a product. Before starting to use the appliance, we recommend you
to carefully read the warnings and recommendations given in the user manual. Thus, you can use
and protect your appliance efficiently for a longer period of time. Please keep this user manual
for future reference.
Intended use
Igniting the
burners
In these models, ignition device and the safety device were combined into the switch. Apply the
following steps to ignite the burners:
1. Turn the pre-selected knob.
2. Press and hold the knob for 3 or 4 seconds to ignite the gas exiting from the burner with spark
and heat the thermocouple.
3. Release the knob approx. after 3 or 4 seconds and set the flame as desired by turning the
knob counter clockwise.
If the flame dies down, repeat the process starting from step 1.
Round point Ø: valve closed;
Large flame Ø: maximum capacity;
Small flame Ø: minimum capacity;
Using the flames
To save from gas and obtain the best efficiency, it is recommended that pots matching the size of the
burners are used in order to prevent overflow of flame from the sides of the pots (see the table).
Automatic safety valve
This safety device shuts off the valve automatically when the flame dies down due to the
overflow of fluid in the utensils or interruption of gas supply from the distribution mains. This
mechanism steps in approximately 30 seconds after the flame dies down.
Cleaning and maintenance of the hob
Before performing any maintenance works on the hob, always unplug it from the wall socket or
disconnect its main power with the circuit breaker in the power distribution panel.
•To avoid any scratches or wears, never use steam cleaners, wire cloth, steel wool or muriatic
acid.
•Never leave acidic and alkaline substances on the hob.
•Never use pointed objects in order not to damage the gaskets between the cooker frame and
the glass-ceramic or the frame and the worktop.
•Do not use the cleaners containing sand, alkaline, acid, chlorine, oven sprays and detergents
which are only used for cleaning the dishwashers.
•Do not use detergent for cleaning purposes since it will lead to permanent bluish stains on the
glass-ceramic surfaces.
•Wipe carefully the remnants of special glass-ceramic cleaning detergent around the cooking
zones with a moist cloth.
•After cleaning the appliance with a moist cloth, dry it carefully at all times in order not to leave
any lime remnants.

•If a fluid containing sugar overflows onto the hob, wipe this immediately with a suitable
sponge.•Wipe the hob carefully with a paper towel or a damp cloth by using a few drops of
detergent which is manufactured particularly for glass-ceramic.
•In the event that sugar, plastic or aluminum folio falls down or are placed onto the hob
accidentally, unplug the hob from the wall outlet.
•After all pan supports, caps and flame rings are removed from the hob it can be cleaned with
warm soapy water. It should be dried carefully after cleaning.
NEVER WASH IN THE WASHING MACHINE.
Make sure that the sections through which gas passes are perfectly clean.
• Natural color of the areas of the pan support, onto which the pots are placed, could change due
to heating in the course of time.
• Hot plate surface should not remain wet or moist. It may lead to oxidation.
Help
In case operational problems occur, contact the Technical Help Center given in the attached list.
Never contact the unauthorized services.
Specify the following data:
- Type of problem;
- Model of the appliance (Art.);
- Serial number (S.N.).

Safety warnings
Consult qualified persons in the following situations:
- installation (see the installation section);
- in case you are not sure about the method of operation.
In the following situations, consult technical support center approved by the
manufacturer:
-After you open the package, if you suspect that the appliance has missing parts; -if the power
cable is changed or damaged; -if the appliance breaks down or does not operate well, request
original spare parts.
General warnings
- Consult authorized technical support centers only and always request use of original spare
parts in order to ensure that this domestic appliance operates efficiently and safely.
- This appliance is designed for domestic use only and it is not intended for professional
purposes. Do no attempt to modify its features;
- Symbols of the countries to which the product shall be delivered and in which its user
manual is valid are specified on the rating plate of the appliance;
- Warranty terms for the electrical system of the appliance are only valid when the appliance is
grounded as prescribed by the laws;
- Avoid touching the pan supports of the hob on which cooking is made, they may be very hot.
Especially keep them away from the children;-use only for cooking, never use for other
purposes;
- Disconnect the appliance from the mains before performing any maintenance works or if it
does not operate smoothly;
- make sure that the knobs are in stop position if the appliance is not in use.
Parts not to be touched by the children:
- the entire system and controls of the appliance in general;
- packaging materials (plastic bags, polystyrene foam, nails, etc.);
- the appliance may be very hot during cooking or right after it is used;
- disabled appliance (in such a case, measures should be taken against the parts which may
pose a danger).
Avoid the following actions:
- touching the appliance with the moist parts of your body;
- using the appliance with bare foots;
- pulling from the hob or its power cable in order to disconnect the appliance from the wall
outlet;
- engaging in inappropriate and dangerous actions;
- leaving the cables that belong to other electrical appliances in contact with the hot parts of
the appliance;
- exposing the appliance to the atmospheric factors;
- using the appliance as a support point;
- using inflammable fluids beside the appliance;
- using adapters, plug multipliers and/or extension cables;
- having unqualified persons to perform the installation and repair works.

GB
Installation
Fig.l
Installation / Fig.2

GB
Controls zone
P1) Rapid Burner
P2) Semi-Rapid Burner
P3) Auxiliary Burner
P4) Ø180 Hot Plate
P5) Ø145 Hot Plate
P6) Triple Burner Wok

Gas connection
Connect the appliance with the gas pipe as per the laws in force and only after you properly
complete the adjustments intended and required for such a gas-operated appliance. Otherwise,
perform the actions given in the paragraph of “replacing the injectors”. To operate the appliance
with liquid gas, use pressure regulators in accordance with the laws in force.
To ensure a tight connection to the gas pipe, place the gasket supplied with the
product in its place. You are supposed to abide by the other rules in force
concerning gas installation. Check with soapy water whether there is a leakage
after completing the connection.
Ventilation of the places
The use of a gas cooking appliance involves the production of heat and humidity in the room in
which it is installed. Make sure that the kitchen is well ventilated; keep the natural aeration
openings open or install a forced aeration device (ventilation hood). Intense and prolonged use of
the appliance may require supplementary ventilation, for example by opening a window or a more
effective aeration such as by increasing the hood speed for example.
Burning the hob
Apply the following in order to access where the functional parts are contained: •remove the pan
supports, caps, burner rings;• dismantle the knobs by removing their shafts; • remove the screws
securing the burners;• pull upwards.
Electrical Connection
The hob in use is equipped with a power cable that has three poles and a free terminal. If the hob
shall remain connected to the mains permanently, install a circuit breaker designed with contact
distances that would allow cutting out the current completely in cases such as heavy-voltage
category III.
Check the following:
a) Plug and wall outlet should comply with 16A current;
b) it should be easily accessible and it should be placed in such a way that no electrical parts are
accessible during the plugging or unplugging of the same plug;
c) Plug shall be removable without any difficulty;
d) If the hob is built into furniture, no pressure should be applied onto the plug when it is plugged
in.

BLUE
YELLOW - GREEN
BROWN
e) 2 electrical appliances should not be connected to the same wall
outlet at the same time;
f) if the power cable will be replaced, H05VV-F type 3xl,5mm2cable
should be used;
g) it is essential that the support poles of the empty terminals be
distinguished (Brown=Phase Blue=Neutral Yellow/Green=Earth).
NOTE: Check that the values of your mains connection (voltage,
maximum power and current) comply with the features of your
hob.
Replacing the injectors
NOTE: These products are already set to operate with LPG (G 0) at the factory. Replace the injectors as
specified below in case a different type of gas is used:
1. Remove the pan support and the burners;
2. Remove the injectors by removing their screws and then install new injectors which are procured in
accordance with the gas type in use and make sure that their brand matches with the one prescribed in the
list.
3. Install the burners and the pan support;
4. No air adjustment is required for these burners.
Warning
If the gas type of the appliance is converted to another type, it is necessary to affix the adhesive label, which
was supplied as accessory, onto the plate. When it is operated with LPG gas (G30), the adjustment screw
should be turned to the end. These appliances are supplied as II 2H3+ category.
Minimum adjustment
-Remove the knobs (they can be removed since they were mounted by being pressed on).
-Ignite the burners and turn the adjustment screw to clockwise to decrease the flame, and turn it
counterclockwise to increase the flame. (Figure 3) You can make the adjustment with a screwdriver.
To decrease or increase the flame in the
burners, you can adjust them by turning
the screws.
Figure 3

Important
- Do not place unbalanced or deformed pots onto the burners since they may overturn or
overflow.
- If the appliance is equipped with a cover, make sure that the appliance cools down before
closing the cover.
- Close the supply valve when the hob is not in use.
- Before the installation process, check the gas distribution conditions and whether these match
with those given on rating plate of the appliance. The gas to be used is marked on the plate at
the bottom of the casing. This appliance is not connected to the discharge system for the
combustion products and it must be installed and connected as per the applicable rules in force.
Please pay special attention to the instructions regarding ventilation. The gas operated hob
generates heat and humidity where it is installed. Make sure that the ambient is well ventilated:
keep the natural ventilation holes open or install mechanical ventilation device (suction hood with
discharge pipe). Intense and long-term use of the appliance require an auxiliary ventilation such
as opening a window or application of a more effective ventilation system, and if it is applicable,
reinforcing the existing mechanical ventilation system.
Manufacturer is not responsible for the possible damages which may arise due to the
following situations: incorrect installation, uses other than intended use, misuse and
inappropriate use.
Installation
Following sections describe the installation processes for the gas and electrical sections. These
processes should be performed by the expert personnel in accordance with the laws in force.
Processes conducted by inexperienced persons may pose a danger. If these instructions are not
complied with, manufacturer shall not accept any liability for personal injuries and material
damages. With regard to the gas section, rules/laws of the country where the appliance is
installed will be in force.
Preparation of the furniture
This manual is intended for Class 4 built-in hob. Prepare the installation location as shown in the
Figure 1. In order to ensure that it can be opened easily under any condition, set it to the most
proper position, make sure that the gas pipe of the hob does not contact with the sides.
Placing into the furniture
After making the connections, apply the EPDM foam, supplied together with the installation
accessories, to the sides of the hollow (create a frame), into which the hob shall be placed, as a
strip line paying attention to apply it as close as possible to the hollow, and lean the hob against
it. Tighten the fixation hooks precisely. Scrape the surplus EPDM foam with a curved knife, etc.
(a sharp instrument).
Important
These appliances are type "Y" in terms of fire protection rating against fire hazards; therefore at
their installation place, they can be installed as built-in close to the wood coated walls higher
than the hob, provided that the you allow a distance of min. 50mm for the sides, min. 30mm for
the back side and min. 700mm for the cupboards to be placed onto it.