Kobalt KID 124B-03 User manual

AS22019
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Español p. 17
ITEM #4913880
BRUSHLESS
IMPACT DRIVER
MODEL #KID 124B-03
KOBALT and logo design are trademarks or
registered trademarks of LF, LLC. All rights reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 888-3KOBALT (888-356-2258), 8 a.m.-8 p.m., EST,
Monday-Sunday. You could also contact us at [email protected].

2
TABLE OF CONTENTS
Product Specications...................................................................................... 2
Packaging Contents.........................................................................................3
Safety Information............................................................................................ 4
Preparation....................................................................................................... 8
Operating Instructions...................................................................................... 9
Care and Maintenance...................................................................................15
Troubleshooting..............................................................................................16
Warranty.........................................................................................................16
PRODUCT SPECIFICATIONS
COMPONENT SPECIFICATION
Rated voltage 24 V
No-load speed (n0) 0-1500 / 0-2400 / 0-3100 /min (RPM)
Collet size 1/4 in. (6.35mm) hex
Maximum torque 2000 in. lbs
Impact rate 0-1900 / 0-3100 / 0-3800 /min (IPM)
Recommended operating, charging and
storage temperature
41°F (5°C) - 104°F (40°C)

3
PACKAGE CONTENTS
MODE
SPEED
123
C
A
PART DESCRIPTION PART DESCRIPTION
A Quick-change collet F LED work light
B Direction-of-rotation selector G Belt clip (with screw)
C Variable-speed trigger switch H Bit holder (with screw)
D Speed button I Impact bit
E Mode button J Handle
WARNING
• Remove the tool from the package and examine it carefully. Do not discard the carton or any
packaging material until all parts have been examined.
• If any part of the tool is missing or damaged, do not attach the battery to use the tool until
the part has been repaired or replaced. Failure to heed this warning could result in serious
injury.
B
J
E
F
D
G
H
I

4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or operate
this product. If you have any questions regarding the product, please call customer service
at 888-3KOBALT (888-356-2258) , 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also
contact us at [email protected].
WARNING
• The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power-tool operation, always wear
safety goggles or safety glasses with side shields and a full-face shield, when needed. We
recommend using a wide vision safety mask over eyeglasses or standard safety glasses
with shields. Always use eye protection marked to comply with ANSI Z87.1.
• Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known to the state of California to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
– Lead from lead-based paints,
– Crystalline silica from bricks and cement and other masonry products, and
– Arsenic and chromium from chemically-treated lumber.
• Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemical: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to lter
out microscopic particles.
Know the Tool
To operate this tool, carefully read this manual and all labels afxed to the tool before using it.
Keep this manual available for future reference.
Important
This tool should be serviced only by a qualied service technician.
Read All Instructions Thoroughly

5
SAFETY INFORMATION
Some of the following symbols may be used on this tool. Please study them and their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and more safely.
SYMBOL DEFINITION SYMBOL DEFINITION
V Volts n0No-load Speed
RPM Revolutions per Minute IPM Impacts per Minute
…/min
Revolutions or Strokes per
Minute
or d.c. Direct Current
N m Newton Meter in. lbs. Inch-Pound
A danger, warning,
or caution. It means
‘Attention! Your safety is
involved.’
To reduce the risk of injury,
user must read instruction
manual.
To reduce the risk of injury,
always wear ear protection.
To reduce the risk of injury,
always wear eye protection.
General Power Tool Safety Warnings
WARNING
• Read all safety warnings, instructions, illustrations and specications provided with
this power tool.Failure to follow all instructions listed below may result in electric shock,
re and/or serious injury.
Save all warnings and instructions for future reference
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Work Area Safety
• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools create sparks, which may ignite the dust or
fumes.
• Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.

6
SAFETY INFORMATION
Electrical Safety
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching
outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Personal Safety
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the inuence of drugs,
alcohol or medication. A moment of inattention while operating power tools may result in
serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or energising power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing
away from moving parts. Loose clothes, jewelry or long hair can be caught in moving
parts.
• If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause severe injury
within a fraction of a second.
Power tool use and care
• Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.

7
SAFETY INFORMATION
• Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result in
a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations.
Battery Tool Use and Care
• Recharge only with the charger specied by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of re when used with another battery pack.
• Use power tools only with specically designated battery packs. Use of any other
battery packs may create a risk of injury and re.
• When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or a re.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modied. Damaged or modied
batteries may exhibit unpredictable behavior resulting in re, explosion or risk of injury.
• Do not expose a battery pack or tool to re or excessive temperature. Exposure to re
or temperature above 265 °F (130 °C) may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside
the temperature range specied in the instructions. Charging improperly or at
temperatures outside the specied range may damage the battery and increase the risk of
re.

8
SAFETY INFORMATION
Service
• Have your power tool serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed
by the manufacturer or authorized service providers.
Impact Driver Safety Warnings
• Hold the power tool by insulated gripping surfaces, when performing an operation
where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool “live” and could give the operator an electric
shock.
Additional Warnings
• Use only with the battery packs and chargers listed below:
BATTERY PACK BATTERY CHARGER
KB 224-03; KB 424-03; KB 524-03;
KB 624-03; KXB 424-03; KXB 824-03
KRC 2445-03; KRC 2490-03;
KRC 2404-03; KDPC 124-03;
KCH 2401-03; KCH 2411-03
PREPARATION
Know Your Impact Driver
Before attempting to use the impact driver, familiarize yourself with all of its operating features
and safety requirements.
Helpful tool (not included): Phillips-head screwdriver.
WARNING
• Do not allow familiarity with the impact driver to cause carelessness. Remember that one
careless moment is enough to cause severe injury. Before attempting to use any tool, be
sure to become familiar with all of the operating features and safety instructions.
• Do not attempt to modify this tool or create accessories not recommended for use with this
tool. Any such alteration or modication is misuse and could result in a hazardous condition
leading to possible serious personal injury.

9
OPERATING INSTRUCTIONS
1. To Attach Battery Pack
a. Align the raised portion on the battery pack
with the grooves on the bottom of the tool, and
then slide the battery pack onto the tool as
shown.
b. Make sure that the latch on the battery pack
snaps into place and the battery pack is
secured to the tool before beginning operation.
NOTICE: When placing the battery pack on the
tool, be sure that the raised rib on battery pack
aligns with the groove on the tool and the latches
snap into place properly. Improper assembly of
the battery pack can cause damage to internal
components.
To Detach Battery Pack
a. Press the battery-release buttons to release the battery pack.
b. Pull the battery pack backward to remove it from the tool.
WARNING
• Battery tools are always in operating condition. Therefore, always remove the battery pack
when the tool is not in use or when carrying the tool at your side.
2. Installing and Removing the Belt Clip
a. Align the rib of the belt clip (G) with the hole on
the base of the impact driver.
b. Insert the screw and tighten the screw securely
with a Phillips-head screwdriver (not included).
c. To remove the belt clip, use a Phillips-head
screwdriver to loosen the screw holding the belt
clip to the impact driver.
NOTE: The belt clip can be installed on the right or
left side of the tool.
SPEED
MODE
SELFTAP
FINISH
123
1
Battery-release
buttons
MODE
SPEED
123
2
Screw
G

10
OPERATING INSTRUCTIONS
3. Installing and Removing the Bit Holder
a. Align the rib of the bit holder (H) with the hole
on the base of the impact driver.
b. Insert the screw and tighten the screw securely
with a Phillips-head screwdriver (not included).
c. To remove the bit holder (H), use a Phillips-
head screwdriver to loosen the screw holding
the bit holder to the impact driver.
NOTE: The bit holder can be installed on the right
or left side of the tool.
4. Direction-of-Rotation Selector
(Forward/Center Lock/Reverse)
The direction of bit rotation is reversible and is
controlled by the selector located above the trigger
switch (C). With the impact driver held in the normal
operating position, pointing away from you:
a. Position the direction-of-rotation selector (B) to
the left of the tool for forward rotation to drive
the screws in.
b. Position the direction-of-rotation selector (B)
to the right of the tool for reverse rotation to
remove screws.
c. Setting the selector in the center position locks
the trigger to helps reduce the possibility of
accidental starting when the tool is not in use.
NOTICE:
• To prevent gear damage, always allow the impact driver to come to a complete stop before
changing the direction of rotation.
• The impact driver will not run unless the direction-of-rotation selector is engaged fully to the
left or right.
5. Variable-speed Trigger Switch
a. Position the direction-of-rotation selector (B) to
the left or right of the tool as needed to unlock
the trigger switch (C).
b. To turn the impact driver ON, depress the trigger
switch (C).
c. To turn it OFF, release the trigger switch.
3
H
Screw
4
Forward
Reverse
5
B
C

11
OPERATING INSTRUCTIONS
NOTE: If there is no other operation within 1 minute after the trigger is released, the tool will
enter standby mode and will revert to the previous setting when the tool is turned on again.
Refer to chapters “Speed Range Selection” and “Mode Selection”.
Variable Speed
The variable-speed trigger switch delivers higher speed with increased trigger pressure and
lower speed with decreased trigger pressure.
Electric Brake
The impact driver is equipped with an electric brake. When the trigger switch is released, the
electric brake engages automatically to quickly stop rotation.
6. Speed Range Selection
The impact driver features a speed button (D)
located on the base of the tool to select among three
different variable-speed ranges :
No load speed,
Impact rate, and
Torque
Speed Range
1 2 3
/min (RPM) 0-1500 0-2400 0-3100
/min (IPM) 0-1900 0-3100 0-3800
in.lbs 850 1600 2000
To engage the speed setting:
a. Attach the battery pack to the tool.
b. Position the direction-of-rotation selector (B) to the left or right of the tool.
c. Depress and release the variable-speed trigger switch (C) to “wake up” the control panel.
d. Press the speed button (D) to set the speed. Every press of the speed button switches the
speed to the next range.
NOTE:
• The impact driver provides lowest speed and torque. One light illuminates;
The impact driver provides medium speed and torque. Two lights illuminate;
The impact driver provides maximum speed and torque. Three lights illuminate.
• The higher the set speed, the more torque the impact driver produces to turn a fastener. The
proper setting depends on the job, the bit type, fastener, and material you are using.
NOTICE:
• The LED indicator will turn off within approximately 1 min after the variable-speed trigger
switch or speed button is released, and will revert to the previous setting when the tool is
turned on again.
SPEED
123
MODE
SELF TAP
FINISH
6
D

12
OPERATING INSTRUCTIONS
• The speed range AND the mode selection cannot be active at the same time. You can only
activate either one of the speed ranges OR one of the modes.
• Do not change the speed setting when the tool is running. The speed range will not change
until you release the variable-speed trigger switch.
7. Mode Selection
This tool features two modes: FINISH and SELF
TAP. The modes are switched using the mode
button (E) located on the base of the tool.
To engage the FINISH or SELF TAP mode:
a. Attach the battery pack to the tool.
b. Position the direction-of-rotation selector (B) to
the left of the tool for forward rotation. FINISH
and SELF TAP modes do NOT work in reverse
rotation.
c. Depress and release the variable-speed trigger
switch (C) to “wake up” the control panel.
d. Press the mode button (E) to select the mode.
Every time you press the mode button, the
mode will be switched. The green light on the mode button will illuminate to indicate that it
is activated.
NOTICE:
• The LED indicator will turn off within approximately 1 min after the variable-speed trigger
switch or mode button is released, and will revert to the previous setting when the tool is
turned on again.
• The speed range AND the mode selection cannot be active at the same time. You can only
activate either one of the speed ranges OR one of the modes.
• When the mode button is pressed with the tool set to reverse rotation, the tool will return to a
specic speed range, but the FINISH and SELF TAP modes will not be available.
SPEED
123
MODE
SELF TAP
FINISH
7
E

13
OPERATING INSTRUCTIONS
MODE APPLICATIONS FEATURE FUNCTION
FINISH Driving self-drilling or
self-tapping screws into
a thin metal sheet.
The tool will stop
automatically
soon after
the impact
mechanism is
engaged.
The FINISH mode allows
the user to work fast with
precision while not damaging
the workpiece. This mode
helps to prevent over-
tightening of the screw and
without damage (stripping) to
the workpiece. The tool drives
a screw at a faster speed
and then automatically stops
when the tool engages impact
mechanism.
NOTE:
The timing to stop the driving
varies depending on the type
of the screw and material
to be driven. Perform a test
driving before using this
mode.
SELF TAP Driving self-drilling or
self-tapping screws into
a thick metal plate.
The tool speed
will slow down
when the impact
mechanism is
engaged.
This mode helps to prevent
the screws from breakage,
stripping the screw heads,
and overtightening. It also
accomplishes quick operation
and good nish at the same
time. The tool drives a screw
with specic speed rotation
and slows down the speed
when it starts to impact.

14
OPERATING INSTRUCTIONS
8. LED Work Light
The LED work light (F), located on the base of
the impact driver, will illuminate when the trigger
switch is depressed. This provides additional light
on the surface of the work piece for operation in
lower-light areas.
The LED work light will turn off after approximately
10 seconds after the variable-speed trigger switch
is released.
• The LED work light will ash rapidly if the
tool has stopped automatically when the tool
became overloaded or too hot. Please wait for
the tool to cool down, at which point it can be
started again.
• The LED work light will ash slowly to indicate that the battery charge is very low. Please
recharge the battery pack.
9. Installing and Removing a Bit
NOTICE: Use only bits with power grooves. Do not
use a bit that has a damaged shank.
This tool is equipped with a one-hand quick clip
sleeve that allows you to quickly install the bit.
To install the bit:
a. Place the direction-of-rotation selector (B) in
the center (lock) position.
b. With one hand, hold the tool. With the other
hand, insert a 1/4 in. (6.35mm) bit into the
hexagonal hole in the quick-change collet. The
bit will be secured automatically.
c. Make sure the bit has been secured properly before any operation.
To remove the bit (Fig. 9):
a. Place the direction-of-rotation selector (B) in the center (lock) position.
b. With one hand, pull the sleeve of the quick-change collet (A) away from the tool and hold it
in place.
c. With the other hand, remove the bit from the quick-change collet.
d. Release the sleeve and check that it returns to its original position.
WARNING
• Use protective gloves when removing the bit from the tool, or rst allow the bit to cool. The
bit may be hot after prolonged use.
SPEED
123
MODE
SELF TAP
FINISH
8
F
9
A

15
OPERATING INSTRUCTIONS
10. Tightening and Loosening Screws and Nuts
a. Install the correct bit.
b. Select the mode as necessary, according to the work piece.
c. Select the suitable speed range for the application. It is advisable to make a trial driving on
a scrap material to determine the speed selection.
d. Apply just enough pressure to keep the bit engaged on the screw or nut.
e. Apply minimal pressure to the variable-speed trigger switch initially. Increase the speed
only when you can maintain full control.
WARNING
• Do not overtighten, as the force of the impact driver can break the fastener. Keep the impact
driver at a right angle to the fastener to avoid damaging the fastener head.
CARE AND MAINTENANCE
All maintenance should only be carried out by a qualied service technician.
Cleaning
Before cleaning or performing any maintenance, remove the battery pack from the tool.
For safe and proper operation, always keep the tool and its ventilation slots clean.
Always use only a soft, dry cloth to clean your impact driver; never use detergent or alcohol.

16
TROUBLESHOOTING
WARNING
Place the direction-of-rotation selector (B) in the center lock position and detach the battery
pack from the impact driver before performing troubleshooting procedures.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The impact driver does not
work.
Battery pack charge is
depleted.
Charge the battery pack.
Bit cannot be installed.Bit does not t the quick-
change collet.
Only use bits with power
grooves. Or use a universal
bit adapter with power
grooves.
Motor overheating. Ventilation slots are
obstructed.
Clean and clear ventilation
slots. Do not cover ventilation
slots with hand during
operation.
The LED worklight ashes
rapidly.
The tool has stopped
working to protect internal
circuits.
Release the trigger switch,
wait for the tool to cool down,
then and start the tool again.
The LED worklight ashes
slowly.
The battery pack charge is
very low.
Charge the battery pack.
The tool suddenly slows down/
stops during driving screw.
The tool is operating in
the wrong mode or speed
range.
Check the selected mode,
refer to the “Speed Range
Selection” and “Mode
Selection” sections.
WARRANTY
For 5 years from the date of purchase, the power tool is warranted and for 3 years from date of
purchase the battery & charger are warranted for the original purchaser to be free from defects
in material and workmanship. This guarantee does not cover damage due to abuse, normal
wear, improper maintenance, neglect, unauthorized repair/alteration, or expendable parts and
accessories expected to become unusable after a reasonable period of use.
If you think your product meets the above guarantee criteria, please return it to the place of
purchase with valid proof of purchase and the defective product will be repaired or replaced at
no charge. This guarantee gives you specic legal rights, and you may also have other rights
that vary from state to state.
Lowe’s Home Centers LLC.
MOORESVILLE, NC 28117
Printed in China

ADJUNTE SU RECIBO AQUÍ
Número de serie Fecha de compra
ARTÍCULO #4913880
DESTORNILLADOR DE IMPACTO
SIN CEPILLO
MODELO #KID 124B-03
KOBALT y el diseño del logotipo son marcas comerciales o
marcas registradas de LF, LLC. Todos los derechos reservados.
¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro
Departamento de Servicio al Cliente al 888-3KOBALT (888-356-2258), de lunes a
domingo de 8 a.m. a 8 p.m., hora estándar del Este. También puede ponerse en contacto
con nosotros en [email protected].

18
ÍNDICE
Especicaciones del producto........................................................................ 18
Contenido del paquete................................................................................... 19
Información de seguridad............................................................................... 20
Preparación....................................................................................................25
Instrucciones de funcionamiento.................................................................... 26
Cuidado y mantenimiento .............................................................................. 32
Solución de problemas................................................................................... 33
Garantía .........................................................................................................33
ESPECIFICACIONES DEL PRODUCTO
COMPONENTE ESPECIFICACIONES
Voltaje nominal 24 V
Velocidad sin carga (n0) 0-1500/0-2400/0-3100/mín. (RPM)
Tamaño de la boquilla de sujeción 6,35mm (1/4”) hexagonal
Torsión máxima 2000 pulg. lb
Clasicación de impacto 0-1900/0-3100/0-3800 /mín. (IPM)
Temperatura recomendada de
funcionamiento, carga y almacenamiento De 5 °C (41 °F) a 40 °C (104 °F)

19
CONTENIDO DEL PAQUETE
MODE
SPEED
123
C
A
PIEZA DESCRIPCIÓN PIEZA DESCRIPCIÓN
ABoquilla de sujeción de cambio
rápido F Luz de trabajo LED
B Selector de dirección de rotación G Presilla para cinturón
(con tornillo)
CInterruptor tipo gatillo de
velocidad variable H Soporte para brocas (con tornillo)
D Botón de velocidad I Broca de impacto
E Botón de modo J Mango
ADVERTENCIA
• Retire la herramienta del paquete y examínela cuidadosamente. No deseche la caja ni
ningún material de embalaje hasta después de examinar todas las piezas.
• Si falta alguna pieza o si está dañada, no coloque la batería para usar la herramienta hasta
reparar o reemplazar dicha pieza. No seguir esta advertencia podría provocar lesiones
graves.
B
J
E
F
D
G
H
I

20
INFORMACIÓN DE SEGURIDAD
Lea y comprenda completamente este manual antes de intentar ensamblar u operar este
producto. Si tiene preguntas relacionadas con el producto, comuníquese con Servicio al Cliente
al 888-3KOBALT (888-356-2258), de lunes a domingo, de 8 a. m. a 8 p. m., hora estándar del
Este. También puede ponerse en contacto con nosotros en [email protected].
ADVERTENCIA
• La operación de cualquier herramienta eléctrica puede arrojar objetos extraños a los
ojos y, de esta manera, causar graves daños oculares. Use siempre lentes o gafas de
seguridad con protecciones laterales y, cuando sea necesario, un protector facial que cubra
todo el rostro antes de comenzar a operar una herramienta eléctrica. Recomendamos
usar una máscara de seguridad de visión amplia sobre los lentes o gafas de seguridad
con protecciones estándar. Siempre use lentes de protección que cumplan con la norma
ANSI Z87.1.
• Parte del polvo causado por el lijado eléctrico, el serruchado, la trituración, el taladro y
otras actividades de construcción contiene sustancias químicas que, según el estado de
California, causan cáncer, defectos congénitos u otros daños reproductivos. Estos son
algunos ejemplos de dichos productos químicos:
– Plomo presente en las pinturas con base de plomo
– Sílice cristalina de ladrillos, cemento y otros productos de mampostería y
– Arsénico y cromo de madera tratada con químicos
• El riesgo que corre debido a la exposición a estos químicos varía según la frecuencia con
que realiza este tipo de trabajo. Para reducir su exposición a estas sustancias químicas,
trabaje en un área bien ventilada y utilice un equipo de seguridad aprobado, como las
mascarillas antipolvo especialmente diseñadas para ltrar partículas microscópicas.
Conozca la herramienta
Para operar esta herramienta, lea cuidadosamente este manual y todas las etiquetas
adheridas a la herramienta antes de usarla. Guarde este manual para referencia futura.
Importante
Solo un técnico calicado puede reparar esta herramienta.
Lea por completo todas las instrucciones