Kobra the Jet-gel User manual

LIBRETTO D’ISTRUZIONI
OPERATING INSTRUCTIONS
BETRIEBSANLEITUNG
INSTRUCCIONES DE MANEJO
MODE D’EMPLOI
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

2 3
KOBRA Jet-gel KOBRA Jet-gel
®
WARNING - IMPORTANT
WHAT’S IN THE BOX
- The hand sanitizing dispenser: KOBRA Jet-gel
- 500 ml bottle of hand sanitizing gel specically made to extend the life of KOBRA Jet-gel
PLEASE READ CAREFULLY THE OPERATING MANUAL AND THE FOLLOWING WARNINGS
BEFORE PLUGGING IN KOBRA JET-GEL HAND SANITIZER.
MAKE SURE THAT VOLTAGE AND MAINS FREQUENCY MATCH THE ONES ON THE LABEL
PLACED NEXT TO THE POWER CORD BEFORE PLUGGING IN THE HAND SANITIZER.
UNPLUG THE POWER CORD WHEN:
- REFILLING THE TANK WITH HAND SANITIZING GEL
- IT IS NECESSARY TO DO MAINTANANCE
KOBRA Jet-gel: an ideal solution for oces, luxury buildings, luxury stores, airports, lounges, casinos,
hotels, resorts, restaurants, bars, private houses, private clubs, tness clubs, museums, theaters and
any other kind of location looking to oer their customers an exclusive experience.
REFER TO THE MANUAL WARNING!
SAFETY PRECAUTIONS
DO NOT LET CHILDREN
OPERATE THE GEL
DISPENSER
WHEN DESIGN MEETS HEALTH
THANK YOU FOR PURCHASING KOBRA JET-GEL.
A DISPENSER DESIGNED TO SANITIZE HANDS
ELEGANTLY, QUICKLY AND SAFELY.
GB

4 5
KOBRA Jet-gel KOBRA Jet-gel
®
100 CM
Figure 1
1
4
2
5
STARTING POSITION
INSTALLATION
After unwrapping the device, place it on a at surface making sure to be close to an outlet.
It is suggested to follow the below steps (see Figure 1) in order to shape the dispenser and give it
the height required for your needs. Once reached the desired shape, ll up the tank as explained
in the following page “Tank Rell”. Finally, plug it in.
UNFOLD IT AND SHAPE IT AS YOU WISH
3

6 7
KOBRA Jet-gel KOBRA Jet-gel
®
Rell tank “A” with the given hand sanitizing gel right after installing KOBRA Jet-gel and before
start using it (see Figure 2).
- Lift tank “A”.
- Turn the closing cap “B” counterclockwise and remove it.
- Fill up tank “A” with the hand sanitizing gel provided. Do not completely ll up the tank but leave
5 cm from the very end of the tank to avoid the gel to overow when inserting the closing cap
back.
- Insert the closing cap “B” back into the tank hole and turn it clockwise keeping the air intake hole
upward
- Reset tank “A” to its original position.
Power plug must be unplugged when relling the tank.
Plug the power cord back in once the rell is complete. Then, press button “C” once.
Now, KOBRA Jet-gel is ready to supply.
Tank capacity: 700 ml.
TANK REFILL
GE
L
Figure 2
EFFORTLESS REFILL
A
B
C

8 9
KOBRA Jet-gel KOBRA Jet-gel
®
HOW TO USE HOW TO USE
- On/Off Dispenser:
Press button “C” once (see Figure 3).
- On/Off Projector:
Press twice (back to back) button “C”.
The project will turn on automatically when turning on the dispenser. If you wish to turn
the projector off, press twice button “C”.
- FIRST INSTALLATION ONLY:
Press and hold button “C” for approximately 20/30 seconds and at the same time place a hand
where the gel is supplied (see Figure 4).
Release button “C” as soon as the hand sanitizing gel is supplied.
This procedure is required when the dispenser is installed to ll up the circuit for the rst
time, speeding up the gel supply or in case the gel is not supplied due to empty circuit.
- Hand sanitizing gel supply:
Place your hand as shown in Figure 4.
The dispenser will turn off Led “D” when supplying gel and it will turn back on Led “D” as soon
as your hand is removed.
KOBRA Jet-gel is ready to supply gel when Led “D” is steady on.
- Empty tank warning:
Led “D” will ash and the dispenser will automatically turn off leaving the led “D” ashing as a
reminder to rell the tank.
Rell the tank and plug in the dispenser.
Press button “C” once. KOBRA Jet-gel is now ready to supply gel.
Refer to the previous page “Tank Rell” to learn more about lling up the tank.
Figure 4
Figure 3
C
D
C

10 11
KOBRA Jet-gel KOBRA Jet-gel
®
IMAGE PROJECTOR
Kobra Jet-gel image projector is already equipped with a standard projected image showing a
hand along with a drop of gel.
The projector diapositive can be customized on request both before and after the purchase of the
device by contacting a KOBRA authorized distributor and by providing the vector graphic of the
projected image to be shown on the oor.
CARE AND MAINTANANCE
It is highly suggested to utilize the authentic hand sanitizing gel KOBRA GEL as it is specically
thought and made to preserve the life of the pumps that provide the gel and therefore, to extend
the life of the product. Additionally, KOBRA GEL is made with a mix of substances that leave the
skin feeling soft and with a pleasant lemon scent.
KOBRA Jet-gel is made with the highest quality of chromed steel.
Please use a microbre cloth when cleaning the product along with soapy water to avoid
unexpected scratches or marks on the chromed surface.
PRODUCT MALFUNCTIONING
In case no hand sanitizing gel is supplied:
- FLASHING LED  rell the tank
- STEADY LED  hold button “C” until the
gel is supplied
- STEADY LED  using a pin, check that
the air intake hole on the
closing cap is not clogged
(see gure 5)
Figure 5
In case of product malfunctioning, please refer to a KOBRA authorized distributor