Kodak C700 - Advantix Zoom Camera User manual

Kodak
C700 Zoom
Camera
ENGLISH/ESPAÑOL/PORTUGUÊS

Camera Identification
(1) (2)
(3) (4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)

Camera Identification (12) (13) (14)
(15)
(16)(17)(18)
(19)
(20)
(21)
(22)
EXP
LEFT
SELECT
TEXT
ENTER
MENU SELECT

LCD Panel
(23) (24) (25)
(26)
(27)(28)(29)(30)(31)
FILL
OFF
EXP
LEFT
SELECT
TEXT

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Your model camera has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits provide
reasonable protection against interference in residential use. The camera generates,
uses and can radiate radio frequency energy and, if not used in accordance with
the instructions, may cause interference to radio communications. There is no
guarantee that interference will not occur. If this camera does cause interference to
radio or television reception, which can be determined by turning the camera off and
on, you may reduce the interference by the following:
— Reorient or relocate the receiving antenna.
— Increase the separation between the camera and the receiver.
— Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

ENGLISH
KODAKADVANTIX
C700 Zoom Camera
Welcome to the innovative world of the Advanced Photo System!
And thank you for buying this KODAKADVANTIX Camera.
NEEDHELPWITHYOURCAMERA?
Go to our web site at http://www.kodak.com or call:
Kodak in your country.
When you call, please have your camera available.
For warranty purposes, please keep your sales receipt as proof of
the date of purchase.
© Eastman Kodak Company, 1998

ADVANCED PHOTO SYSTEM
FEATURES AVAILABLE WITH
THIS CAMERA
Triple format selection
• You can take three different size pictures:
Classic (C), Group/HDTV (H), and
Panoramic (P) pictures from the same film
cassette. The viewfinder frame changes to
match each format selection.
Date and time imprinting/titling
• You can choose to have date and time
information printed on the back of your
prints. With this camera, you can also
choose a print title from the Title-Select
List and a language (see Setting the
Language) before you take a picture.
You also have the option to choose an
additional title for the entire roll of film. The
selected titles will be printed on the back of
your prints. See your photofinisher for a full
description of available services.
Double exposure protection (DEP)
• You don’t need to worry about accidentally
re-exposing your film. Your camera reads
the Film Status Indicator (FSI) on the film
cassette to prevent re-exposure.
Mid-roll change (MRC)
• You can change and remove film in the
middle of the roll and reload it later to
continue picture-taking. When you reload
the film cassette into the camera, the
magnetic Information Exchange (ix)
technology of the camera will automatically
rewind the film to the first unexposed frame.
This feature allows you to switch to another
film speed at mid roll to match scene
requirements, e.g., the use of high-speed
film for indoors verses low-speed film for
outdoors. Also, you can dedicate individual
film rolls to specific subjects or share the
camera with the family while each member
uses their own film cassette.
Picture quality information exchange
(PQix)
• Your camera features magnetic information
exchange that records information about
lighting conditions and exposure on the film
cassette to assist the photofinishing lab
with color correction and exposure
adjustments, providing you with the best
possible results.

3
Film status indicator (FSI)
A highlighted indicator advances from
one symbol to another to identify the
status of the film inside the cassette.
4
3
2
1
Look for this logo to be certain that the film you buy is
made for this camera.
Look for this logo to select a certified photofinisher for
developing your film and to assure that you get all the
features of the Advanced Photo System.
Processed negatives
Fully
exposed
Partially
exposed
Unexposed

4
CONTENTS
CAMERA IDENTIFICATION............................. 5
ATTACHINGTHE STRAP ................................ 6
LOADINGTHEBATTERY ................................ 6
Low-battery indicator ................................... 7
Battery tips .................................................. 7
Power shut-off ............................................. 7
LOADING THE FILM ........................................ 8
TAKING PICTURES......................................... 9
Typical print sizes (formats) ....................... 10
Using the zoom lens .................................. 10
TAKING FLASH PICTURES .......................... 11
Flash-lamp signals .................................... 11
Flash-to-subject distance .......................... 12
SELECTING FLASH MODES AND
INFINITY-FOCUS MODE .......................... 12
“FILL FLASH” ............................................ 13
“INFINITY ” ................................................ 13
“FLASH OFF” ............................................ 13
USING THE “SELFTIMER” ............................ 14
DATE AND TIME IMPRINTING ...................... 14
Setting the date and time .......................... 14
Date and time formats ............................... 15
Changing the date and time
formats ............................................... 15
USING THE “SET DISPLAY”.......................... 16
SETTINGTHE LANGUAGE ........................... 16
PRINT TITLE IMPRINTING............................ 17
ROLL TITLE IMPRINTING ............................. 17
Title-select list............................................ 18
UNLOADING THE FILM................................. 19
Automatic rewind ....................................... 19
Mid-roll change (MRC) .............................. 20
CARING FOR YOUR CAMERA ..................... 20
TROUBLESHOOTING ................................... 21
SPECIFICATIONS.......................................... 23

5
CAMERA IDENTIFICATION
(Unfold the front and back cover flaps of manual for camera diagrams.)
17 FILM - DOOR LATCH
18 ENTER BUTTON
19 SELECT BUTTON
20 FILM - REWIND BUTTON
21 MENU BUTTON
22 TRIPOD SOCKET
LCD panel
23 INFINITY - FOCUS INDICATOR
24 BATTERY SYMBOL
25 TEXT - MESSAGING PANEL
26 FRAME COUNTER
27 FILM - PRESENCE INDICATOR
28 SELF - TIMER INDICATOR
29 FILL - FLASH INDICATOR
30 FLASH INDICATOR
31 OFF - FLASH INDICATOR
1 ZOOM - DIAL LEVER
2 SHUTTER BUTTON
3 LENS COVER / FLASH
4 FORMAT - SELECTOR BUTTON
5 VIEWFINDER
6 LIGHT SENSOR
7 LENS
8 SELF - TIMER LAMP
9 AUTO - FOCUS SENSORS
10 STRAP POST
11 BATTERY DOOR
12 VIEWFINDER EYEPIECE
13 FLASH / CAMERA - READY LAMP
14 LCD PANEL
15 FILM DOOR
16 FILM CHAMBER

6
ATTACHING THE STRAP
1. Insert the shorter looped
end of the strap
behind the STRAP
POST (10).
2. Thread the longer end
of the strap through
the shorter loop.
3. Pull the strap tight.
LOADING THE BATTERY
This camera uses one
3-volt lithium KODAK
K123LA (or equivalent)
Battery that supplies
power for all camera
operations.
1. Open the BATTERY
DOOR (11) by using
your finger tip.
• Before you remove
the old battery, close
the lens cover/flash.
2. Insert the battery
into the chamber
asshown.
3. Snap the
battery door
closed.
• After you
load a new
battery into
the camera, you will need to reset the
date and time.

7
Low-battery indicator
It’s time to replace the battery when—
• the BATTERY SYMBOL (24) “blinks” and
the “BATTERY LOW” message
appears on the LCD panel or
• none of the indicators, except for steady
battery symbol, appears on the LCD
panel and the shutter button cannot
be released.
Battery tips
• Remember to keep a spare battery with
you at all times.
• Read and follow all warnings and
instructions supplied by the battery
manufacturer.
• Keep batteries away from children.
• Do not try to take apart, recharge or
short circuit the battery, or subject it to
high temperature or fire.
• Store batteries in their original
packaging prior to use.
Power shut-off
To save battery power, the camera will
automatically go into a sleep mode if it is
not operated for more than 60 seconds.
You can press the shutter button, zoom
control, film-rewind, mode buttons or
rewind button to awaken the camera.

8
LOADING THE FILM
You can load film into the camera with the
lens cover/flash opened or closed.
1. Turn the camera upside down and
slide the FILM-DOOR LATCH (17) to
automatically open the FILM DOOR (15).
• The film door will open only when the
film chamber is empty or the film in
the camera is completely rewound
into the film cassette.
2. Insert the film cassette completely into
the FILM CHAMBER (16).Make sure the
Film Status Indicator (FSI) on the film
cassette is at ●(#1 position) for a new
cassette or at ◗ (#2 position) for a
partially exposed cassette.
•Do not force the film cassette into
the film chamber.
3. Close the film door to start the auto-
film advance. The FRAME COUNTER (26)
on the LCD PANEL (14) will show the
number of frames remaining on the film
cassette.
• After you close the safety-interlock
film door, you cannot open the door
until the film is completely rewound
into the film cassette.

9
TAKING PICTURES
You can take Classic (C), Group/HDTV (H)* ,
and Panoramic (P) pictures on the same
film cassette (see the table on the
following page for Typical print sizes).
Your photo-processing cost may be based
on the format sizes(s) that
you use to expose the film.
1. Lift the LENS COVER/
FLASH (3) up to
uncover the
LENS (7) and
to activate
the flash.
2. Press the
FORMAT-SELECTOR
BUTTON (4) to the desired
format (C, H, or P).
The viewfinder will
change to show the
selected field
of view.
3. Frame your subject within the
VIEWFINDER EYEPIECE (12). For a sharp
picture, stand at least 0.8 m from
your subject.
4. Partially depress the
SHUTTER BUTTON (2)
until the FLASH/
CAMERA-READY
LAMP (13) turns green.
Fully depress the
shutter button to take
the picture.
• Follow the instructions
on the LCD text-
messaging panel when
the flash/camera-ready
lamp is red.
MULTI
AF
CP
H
CP
H
CHP
* High Definition Television (HDTV) prints are
the same aspect ratio as the TV for CD
interface capabilities.
CP
H

10
Typical print sizes (formats)
CHP
Classic Group(HDTV) Panoramic
88.9 x 127 mm or 88.9 x 152 mm or 88.9 x 216 mm to
102 x 152 mm 102 x 178 mm 102 x 292.7 mm
NOTE:Yourphotofinisherwillgenerallyprovide
102 x 152, 102 x 178, and 102 x 292.7 mm sizes. Some
localprinters mayoffer 88.9x 127,88.9 x 152, and
88.9 x 216 mm sizes.
Using the zoom lens
This camera has a motorized-zoom lens
that lets you select the ideal lens-focal
length for taking pictures. When you turn
the camera on, it is initially set to the
wide-mode position.
1. Lift the LENS COVER/FLASH (3) up to
uncover the LENS (7) and to activate
the flash.
2. Slide the ZOOM-DIAL LEVER (1) to the
left to the wide-mode position to
zoom away from
the subject. Slide
the lever to the
right to the tele-
mode position to
zoom closer to
the subject.
3. Frame your subject
within the VIEWFINDER
EYEPIECE (12).
4. Partially depress the SHUTTER
BUTTON (2) until the FLASH/CAMERA-
READY LAMP (13) turns green. Fully
depress the shutter button to take the
picture.
• The lens barrel will automatically
return to the wide-mode position after
approximately 60 seconds.

11
TAKING FLASH PICTURES
In dim light, such as indoors or outdoors
in heavy shade, or on dark overcast days,
you need flash. Your camera features an
automatic flash that fires when you need
it and provides automatic daylight fill flash
under certain bright-light conditions
where shadows may exist. The flip-up
flash also helps to minimize red eyes in
flash pictures and to prevent hand
obstruction in front of the flash.
When you partially depress the shutter
button and the flash-ready lamp glows
green, the flash is fully charged and ready
for picture-taking (see the following tables
for Flash-lamp signals and Flash-to-
subject distance).
1. Lift the LENS COVER/FLASH (3) up to
uncover the LENS (7) and to activate
the flash.
2. Take the picture when the FLASH-READY
LAMP (13 )glows green.
• The LCD panel will display “FLASH
NOT READY” message when the
flash is not fully charged.
3. Keep the subject within the distance
range for the speed of film in your
camera. Don’t take pictures beyond the
maximum distance or your pictures will
be dark.
Flash-lamp signals
Lamp Indicator Situation
Glows green Flash fully charged
“Blinks” red * Flash not fully charged
Glowsred Subject closer
than0.8 m
*A text message will appear on the LCD panel
to inform the user the reason of warning.

12
Flash-to-subject distance
ISO
Film Wide Tele
Speed (30 mm) (60 mm)
50 0.8 to 2.7 m 0.8 to 2.4 m
100 0.8 to 4 m 0.8 to 3.4 m
200 0.8 to 5.5 m 0.8 to 4.6 m
400 0.8 to 7.9 m 0.8 to 6.7 m
800 0.8 to 11 m 0.8 to 9.4 m
1600 0.8 to 15.8 m 0.8 to 13.4 m
SELECTING FLASH MODES AND
INFINITY-FOCUS MODE
Besides the “ AUTO FLASH” mode, you
canselect “ FILLFLASH ,”“ INFINITY ,”and
“ FLASHOFF .”
Press the SELECT BUTTON (19) until the
desired indicator and corresponding text
message appear on the LCD PANEL (14).
Flash modes and the infinity mode
remain selected after you take the
picture. To cancel the selection, close the
lens cover/ flash or press the SELECT
button to return to the standard point-
and-shoot “AUTO FLASH ” mode.

13
“FILL FLASH”
When bright light indoors or outdoors
comes from behind the subject
(backlighting), dark shadows (especially
on faces) may occur. Use fill flash to
lighten these shadows.
1. Press the SELECT BUTTON (19) until the
“FILL FLASH” message and indicator
appear on the LCD PANEL (14).
2. Frame your subject within the
VIEWFINDER EYEPIECE (12).
3. Press the SHUTTER BUTTON (2) to take
the picture.
“INFINITY ”
For maximum sharpness of distant
scenery at any zoom position, use the
infinity feature (for outdoor use only).
1. Press the SELECT BUTTON (19) until the
“INFINITY” message and indicator
appear on the LCD PANEL (14).
2. Frame your subject within the
VIEWFINDER EYEPIECE (12).
3. Press the SHUTTER BUTTON (2) to take
the picture.
“FLASH OFF”
When you do not want to use the flash,
especially indoors where flash is
prohibited, such as in theaters and
museums, or when you want to take
twilight scenes or distant subjects that are
beyond the flash range, or capture the
ambiance of existing light, use the flash-
off feature.
1. Press the SELECT BUTTON (19) until the
“FLASH OFF” message and indicator
appear on the LCD PANEL (14).
2. Frame your subject within the
VIEWFINDER EYEPIECE (12)
3. Press the SHUTTER BUTTON (2) to take
the picture.
• Use a tripod and high-speed film
because the shutter speed in these
situations will most likely be slow.
FILL
OFF

14
USING THE
“SELFTIMER”
You can include yourself in pictures
by using the self-timer feature. The
electronic self-timer will delay the
release of the shutter button for
approximately 10 seconds after you
press the shutter button.
1. Place the camera on a tripod (TRIPOD
SOCKET [22]) and press the ENTER
BUTTON (18).The
“SELFTIMER
READY ” message and indicator will
appear on the LCD PANEL (14).
2. Frame your picture in the VIEWFINDER
EYEPIECE (12).
3. Press the SHUTTER BUTTON (2). The
SELF-TIMER LAMP (8) on the front of the
camera will blink during the self-timer
countdown.
• To cancel the self-timer selection
before the shutter releases, press the
ENTER button or close the lens-
cover flash.
• The self-timer is automatically
canceled after the shutter releases.
DATE AND TIME IMPRINTING
This camera has a quartz clock and
automatic calendar through the
year 2099.
Traditional cameras print date and/or time
information directly onto the film. Your
camera uses the film’s magnetic data
strip to record date and time information
which your photofinisher imprints on the
back of your photographs.
Setting the date and time
1. Repeatedly press the MENU
BUTTON (21) until the LCD PANEL (14)
displays“ SETDATE .”
2. Press the SELECT BUTTON (19) to select
the date function. The first two digits of
the date (indicating the month) will
“blink.” Press the ZOOM-DIAL LEVER (1)
to the right or left to increase or
decrease the number.

15
3. Press the ENTER BUTTON (18) to store
the selected month and to activate the
next “blinking” date option (follow
steps 2 and 3 to complete your
selection).
• After you set the “date” or “time,”
the LCD panel will display “DATE IS”
or “TIME IS” followed by the
selected date or time.
4. Repeat steps 1–3 to choose
“ SET TIME ” and set the selection.
Date and time formats
The date and time formats are automati-
cally set for you according to the
designated language listed below. If you
want to change the automatic settings
for date and time formats, see Chang-
ing the date and time formats.
Time
Format Date Format
English 12hour month, day,year
German 24hour day, month,year
French 24hour day, month,year
Spanish 24hour day, month,year
Japanese 24hour year,month,day
Changing the date and time formats
(mm,dd,yy/dd,mm,yy/yy,mm,ddand 12/24hour)
1. Repeatedly press the MENU
BUTTON (21) until the LCD PANEL (14)
displays“ SETDATEFORMAT .”
2. Press the SELECT BUTTON (19) to make
the selection. Press the ZOOM-DIAL
LEVER (1) to the right or left to increase
or decrease the number.
3. Press the ENTER BUTTON (18) to store
the selected format.
• After you set the “date” or “time,” the
LCD panel will display “DATE
FORMAT IS” followed by the selected
format.
4. Repeat steps 1–3 to choose and “ SET
TIMEFORMAT .”