Kogan KA3TKBLBKBB User manual

3-IN-1 TRIKE AND BALANCE BIKE
KA3TKBLBKBB, KA3TKBLBKWB, KA3TKBLBKGB

Ensure to read all instructions and warnings in this user guide prior to assembly and use.
Retain this user guide for future reference.
•Adult assembly is required for this bike.
•Adult supervision is required at all times when children are riding the bike.
•Ensure all components of the bike are well connected before use.
•WARNING: To avoid risk of suffocation, keep the plastic packaging away from
children.
•The bike is suitable for children aged 12–36 months.
•The bike must be used in a flat, unobstructed location to ensure that it does not tilt
during normal use and cause injury.
•Do not use the bike near stairs, thresholds, and steps.
•Do not use this bike in busy areas (for example, on roads, downtown).
•Only one child is permitted on the bike at any given time.
•Ensure children do not spend longer than one hour on the bike at any given time.
•Ensure children wear a safety helmet and knee pads before riding the bike.
•Do not use this bike near heaters, stoves, fire, and other heat sources.
•This bike has a maximum load capacity of 25kg. Do not place anything or anyone
heavier than 25kg on this bike as this may lead to injuries to users and damage to the
bike.
•Ensure the saddle is secure before use.
•Ensure all locking devices are locked before using the bike.
•The bike should be used with caution as skill is required to avoid falls or collisions
causing injury to children or third parties.
•Perform regular checks to ensure the screws and components are secure and the
bike is not damaged. If damaged, stop use immediately and contact
help.Kogan.com for assistance.
Cleaning and care
•Clean the bike body with a dry cloth. If there is significant dirt, wash the bike with
water and dry with a cloth.
•Store the bike in a dry area.
•Lubricate the axle and rotating parts regularly. This will extend the lifespan of the
bike and maintain its condition.
SAFETY & WARNINGS

AFront bike frame (x1) A-1 Rear bike frame (x1) BHandlebar (x1)
C Front wheel assembly (x1) C1 Pedal fixture (x1) DSaddle (x1)
EAllen key/Phillips head
screwdriver (x1)
COMPONENTS

Step 1: Using the Allen key/Phillips head screwdriver (E), remove the screws secured in the
rear bike frame (A-1). Align and insert the rear bike frame (A-1) into the front bike frame (A).
Using the Allen key/Phillips head screwdriver (E), insert and tighten the removed screws
through the holes of the two components (A, A-1).
E(x1)
Step 2: Place the pedal fixture (C1) onto the front wheel assembly (C).
ASSEMBLY
A-1
A
C1
C

Step 3: Insert the front wheel assembly (C) through the tube on the front bike frame (A). The
top of the front wheel assembly (C) should protrude out slightly.
Step 4: Using the Allen key/Phillips head screwdriver (E), loosen and remove the screw and
nut from the handlebar (B). Insert the handlebar onto the protruding part of the front wheel
assembly (C). The handlebar will then rest on top of the front bike frame (A).
Align the two holes on the handlebar with those on the front wheel assembly (C), then using
the Allen key/Phillips head screwdriver (E), reinsert and tighten the screw into one hole
whilst holding the nut on the other.
E(x1)
Note:
Do not tighten the handlebar with a torque of more than 15Nm.
A
C
Nut
Screw
B
C

Step 5: Using the Allen key/Phillips head screwdriver (E), loosen the back tube on the front
bike frame (A). Insert the saddle (D) through the tube at the desired height and using the
Allen key/Phillips head screwdriver (E), tighten to secure.
E(x1)
Notes:
•Ensure the saddle is inserted at least beyond the safety mark located on its tube.
•Ensure the saddle is tight enough that it does not rotate.
•Do not tighten the saddle with a torque of more than 15Nm.
D
A

Press the left and right buttons on the pedal fixture (C1) to release the pedals. Insert the
pedals onto either side of the front wheel. They should click into place. This completes the
balance bike.
CONVERTING TO BALANCE BIKE
C1
Buttons

Step 1: Press the rear frame button and open the rear legs. This button will pop back up
once the legs are fully open. Reinsert the rear wheel lock between the legs to secure their
position.
Step 2: Press the rear wheel buttons and rotate the rear wheels outwards. This completes
the trike.
Rear frame
button
Rear wheel
button
Rear wheel
button
Note:
If you would like the bike to remain in a balance bike form, do not open the legs.
Rear wheel lock
CONVERTING TO TRIKE

Press the buttons on the pedals and detach the pedals from the front wheel. Insert them
back onto the pedals fixture (C1). These should click into place. This will create the slide
bike.
Handle adjustment
In any form (balance bike, trike or slide bike), the angle of the handle can be adjusted to suit
your child’s height. To adjust, press and hold the handle buttons then move the handle
forward/backward to the desired angle.
USE & FOLDING
CONVERTING TO SLIDE BIKE
Handle button
Handle
button

Folding
After using the bike, it can be folded back for easier storage.
Step 1: Press the rear wheel buttons and rotate the rear wheels inwards.
Step 2: Pull out the rear wheel lock. Press the buttons on the pedals and detach the pedals
from the front wheel. Insert them back onto the pedals fixture (C1). These should click into
place.
Press the rear frame button and close the rear legs together. The rear frame button will pop
back up once the rear legs are fully closed. Insert the rear wheel lock between the legs to
secure their position.
Rear wheel
button
Rear wheel
button
C1
Rear frame
button
Rear wheel lock
Rear wheel lock

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com