Kogan estelle ESIONFCSTMA User manual

NANO IONIC FACE
STEAMER HUMIDIFIER
ESIONFCSTMA

•Read all of the following instructions before use. Keep this user guide for future
reference.
•There may be residual water in the device’s tank when you open the package. That is
the residual water from the device testing. It will not lead to any health problems.
•When new, this device will have some plastic smell. To reduce the plastic smell, it is
recommended to run the device with 40mL of water and a few drops of vinegar prior to
first use. Ensure the vinegar water is completely depleted (no more steam coming out
from the device) before turning off and cooling down the device.
•Do not use this device near bathtubs, sinks, or in areas where exposure to moisture is
likely.
•Do not use this device if you are sensitive to heat. It may result in burns or scalds.
•The device must not be used by:
oPeople during pregnancy or while menstruating, as it may cause skin problems
due to hormone imbalance.
oPeople who have allergies, skin diseases, dermatitis, skin allergies or severe
sunburn.
oPeople with skin problems, like eczema or swelling.
oPeople who are recovering after a surgery.
•Do not touch any metal parts of the power plug when the power supply is turned on.
•When not in use, turn off the power supply and unplug the power plug, otherwise it may
cause fire.
•Use only with the supplied 300W power adapter.
•Ensure that the plug is fully inserted into the power socket while using this device,
otherwise it may cause electric shock.
•Do not pull or insert the plug with wet hands, otherwise it may cause electric shock or
may lead to short circuit.
•Do not use or store the device in a bathroom or in a wet room, as this may result in
electric shock or short circuit.
•Do not allow children to use this device as it may cause burns, electric shock.
•Do not use this device near flammable materials (e.g. alcohol, petrol, nail polish,
remover, spray, etc.), otherwise it may cause fire.
•Use only distilled water or purified water, otherwise it may lead to device failure or even
burns.
•Do not touch the steam when operating the power switch. Keep your face and hands at
least 20cm from the nozzle.
SAFETY & WARNINGS

•During use or within 10 minutes after use, do not tilt, shake, or move the device.
Otherwise the hot water may leak, or a lot of steam would come out from the steam
outlet.
•After using this device, let the water completely cool down, then pour out the remaining
water. Ensure to hold the device while pouring out the water.
•Ensure to drain out the water. Clean the water droplets on the steam outlet. Otherwise,
hot water might spill out when the power supply is turned on for the next use.
•Put this device on a flat surface while using, do not hold it on your hand.
•Do not move the device during use or within 10 minutes after use, as there will still be
steam release after the power is turned off. Do not go near the steam outlet
•Ensure to use distilled water or purified water. Using different water quality may shorten
the service time of the device.
•Tap water, mineral water, hydrothermal acid water, alkaline water contains high mineral
content and should not be used.
•Do not mix any other substances in the water, such as laundry liquid, aromatic oil and
so on. It may cause burns, malfunctions or shorten the service time of the devices
Skin Care Tips
•Do not overuse. Excessive use will make the skin pores open too much.
•Do not use more than 2 times a day. Each time not more than 10 minutes. For normal
skin, use it 3-5 times a week. For sensitive skin, use once a week.
•Cease use immediately if you experience any pain or abnormalities on your skin.
Before First Use:
When new, this device will have some plastic smell. To reduce the plastic smell, it is
recommended to run the device with 40mL of water and a few drops of vinegar prior to
first use. Ensure the vinegar water is completely depleted (no more steam coming out
from the device) before turning off and cooling down the device.

1. Place the device on a flat and sturdy surface.
2. Use the measuring cup to add water to the tank. Do not exceed the maximum
water level.
3. Align the spray head to the spot on the device as shown in the image. Twist 90°
clockwise, to lock it into the device’s tank.
OVERVIEW
Tank
Steamer Head
Power Button
ASSEMBLY
Add Water

Using the Device
1. Plug the power cord into a power outlet. Turn on the power supply. Press the power
button.
2. The steaming will start after 20 seconds. When steaming, the water droplets may
spill out. This may be caused by adding too much water. Ensure to use the
measuring cup to add water. Do not exceed the marked ‘MAX’ water level line
(50mL).
Note: To reduce risk of burns, it is recommended to use 40-45mL of water per use.
Exceeding the maximum capacity may cause water to splash and create risk of
burning.
3. To ensure the steam covers entire face, keep the face 20 cm (or more) away from
the nozzle edge.
4. When the amount of water is insufficient, the steam will be weakened. When the
water in the tank is completely used, the releasing of steam will stop. Average use
time is 8-10 minutes, to empty all water.
5. If you want to continue using the device, then turn it off, wait for 10 minutes before
you to use the device again. Follow the instructions in this section.
6. After steaming, turn off the device and the power supply. Store it after it cools down
completely. Moisturise your face skin, otherwise your face may feel dry.
Operation Advice
•Recommended steaming session length is 8-10 min of continuous use, which is
equivalent to approximately 45mL of water. This will ensure the water tank is
completely emptied and ready for next use.
•After each use, ensure all excess water is emptied. Failure to do so may cause:
•Bacteria developing in residual water, unhygienic for future use
•Accidentally overfilling water tank for future use
OPERATION

•Ensure all excess water in the tank is removed.
•Cool the device for at least 10 minutes after use.
•Disconnect from the power supply. Drain the remaining water in the tank. Wipe
water on the surface of the device.
•To drain remaining water, twist to remove the spray head from the device’s body.
Hold the device to drain the water.
•Clean the device once a month. Use a dry cloth to wipe off the dust, especially on
the power plug.
•Add water into the tank. Insert the spray head and gently shake the device 3 or 4
times. Do not tilt the device while shaking. Drain the water. Repeat this draining
process for 2 or 3 times to clean the water tank.
Rated Power
300W
Rated Voltage
220V-240V
Steam Volume
6.5g/min
Water Tank Capacity
65ml
CLEANING & CARE
SPECIFICATIONS

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com