Kohler K-5486T-2 User manual

-1-
BARDON
INSTALLATION INSTRUCTIONS
HIGH-SPEED TOUCHLESS HAND DRYER
K-5486T-2/K-5486VN-B
·
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
This product complies with GB 4706.1 and GB 4706.15.
·
·
·
·
-
GB 4706.1 GB 4706.15
BEFORE YOU BEGINBEFORE YOU BEGIN
SPECIFICATIONS
Activation
Dime sions
WHD
n
Voltage
Power Warm Air
Cold Air
Detection Distance
Air Temperature
Operation Duration
Motor Type
Air Velocity
Activated by an infared sensor. The
machine operates automatically.
35~40 C 10cm from air outlet
Ambient temperature 25 C(77 F)
o
oo
45 sec
(Self-protection automatic shutoff)
Induction with brush
30 4cm for A4 white paper
WHD 262 225 184mm262 225 184mm
220V, 50Hz220V, 50Hz
1750W1750W
550W550W
10cm 35~40 C
25 C (77 F)
o
oo
45
()
AC 220V 50Hz 105m/s 10%
AC 220V 60Hz 110m/s 10%
30 4cm
AC 220V 50Hz 105m/s 10%
AC 220V 60Hz 110m/s 10%
KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD,
JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436
( ) 158 200436
261
225
184
134
200
©
©
Copyright Kohler China Investment Co., Ltd. 2020
2020
1302273-T01-C

-2-
WARNING:
WARNING: Danger of electric shock.
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
Danger of electric shock. Do not open
the casing.
Do not use the
device at damper places such as the shower room.
Do not transform or disassemble the
device to avoid fire or electric shock.
Use rated voltage. The device will break
down if the rated voltage exceeds 10% and may
cause fire or electric shock.
Use separated circuit to avoid fire caused
by over heating of the shunt circuit.
To avoid danger, the damaged wire must
be replaced by manufacture or other professionals.
Do not let children play on the device to
avoid the device from dropping down.
Do not place other items on the device.
10%
60cm 40cm
110~120cm
STANDARD INSTALLATIONSTANDARD INSTALLATION
WARNING: Risk of electrical shock.
WARNING: Risk of electrical shock.
WARNING: Risk of electrical shock.
A licensed
electrician should make all electrical connections.
Connect only to
a circuit protected by a Ground-Fault Circuit-
Interrupter (GFCI) or Earth-Leakage Circuit-Breaker
(ELCB).
Disconnect
power before servicing.
() ( )GFCI ELCB
·
·
This machine is equipped with an infrared sensor for
automatic activation.
The product is made in China.
·
·
1302273-T01-C

Problem
Hand dryer
does not
function
No warm air
Motor does
not function
Check
Check the power
switch.
Sensor wire is loose.
Sensor is damaged.
PTC heating
assembly is
damaged.
Check whether
ambient temperature
exceeds 25 .
Motor is damaged.
Wind wheel is stuck.
Action
Turn on power.
Connect wire.
Contact
professionals.
Heating is
automatically shut
off when ambient
temperature
exceeds 25 .
PTC
25
25
Note: The device must be repaired by professionals.
Repair without technical assistance may damage the
parts or cause personal injury.
-3-
TROUBLESHOOTING
OPERATION DIAGRAMOPERATION DIAGRAM
L
N
Power
AC220V
Switch
Fuse
Circuit Board
Display Light
Temperature Control Probe
Sensor Probe
Control Relay
Motor
Temperature
Control Switch
Heater
Thermal Fuse
NOTE
1. Make sure the sensor is located min
60cm(23 inch) above everthing
bellow to prevent false triggers.
2. Never install hand dryer onto a
wooden or plastic wall finish.
3. Before installation, make sure the
power source complies with
specification of the machine.
1. 60cm
2.
3.
BEFORE INSTALLATIONBEFORE INSTALLATION
Minimum 60cm
60cm
1302273-T01-C

-4-
3. Insert screws into dowels and tighten them. (Fig.2)
3. ( 2)
4. Connect AC power cable (Fig.3). The cable can be hidden.
4. ( 3)
Fig.2
2
Fig.3
3
INSTALLATION
A. Installation Steps
1. Paste the installation template at appropriate location on
the wall.
2. Drill four holes, dia 8mm insert plastic dowels. (Fig.1)
2. 8mm
(1)
A.
1.
8mm
Fig.1
1
Cap
Null Line
Grounding Line
Power Line
1302273-T01-C

Fig.4
4
B. Installation Check
1. Check AC power cable connection.
2. Check if AC power on.
3. Put outer cover back.
4. Insert security screws and tighten them.(Fig.4)
B.
1.
2.
3.
4. ( 4)
C. Test Running C.
D. Operation Instructions
1. The machine starts operating automatically when user's
hands are put approximately 20cm (7.78") below the
sensor located next to air louver. Whenever the hands are
moved out of sensing range, the machine will stop after
approx. 0.5 sec.
2. The 0.2 sec time delay helps avoid false triggers by
unexpected movements.
3. For safety reasons, the machine will immediately stop
operating when it is used continuously over 45 seconds.
The machine resumes to standard function when hands
are moved away.
D.
1. 20cm
0.5
2. 0.2
3. 45
-5-
Steps
1. Shake
the
device
slightly.
1.
2. Check
power
voltage.
2.
3. Plug in. 3.
4. Put
hands
below the
device for
drying.
4.
Results
The device is firmly
fixed.
Use rated voltage.
Switch off external
power.
Air goes out at a
high speed.
Check the power if
the display light is
not on.
The device may be
burnt or cause
personal injury if not
running under rated
voltage.
There may be
abnormal sounds or
vibrations if the
device is not firmly
fixed.
Check if hands are
too far away from
the sensor if there is
no air going out.
Note
1302273-T01-C

E. Important Notice
1. Turn off power supply prior to removing outer case.
2. Turn off power supply before maintenance or cleaning. If
Casing is covered with dust, do not splash water onto it.
Use only damp sponge or cloth to wipe dirt off.
3. Do not use eradicator, abrasive powder or oil, acid or alkali
liquid detergent to clean casing.
4. Never try to put a small screw-driver or any other object
into the holes of air Louver from outside. This might cause
damage to the interior parts, and electric shock may occur.
5. Keep sensor case clean, never use any abrasive cleaning
agent, rough surface articles, steel brush or sandpaper to
rub the sensor case. This will make the sensor case dull
and decrease the sensitivity of sensor.
6. Do not dry other objects except hands to ensure the safety.
7. To avoid damage to the machine or cause physical harm to
the person, please keep the live parts away from water.
8. Do not bump the casing.
9. For indoor installation and use only.
E.
1.
2.
3.
4.
5.
6.
7.
8.
9.
-6-
1302273-T01-C