Kohler CANDIDE 660 User manual

BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. For new installations, assemble faucet and drain to lavatory before installing lavatory.
660/660-ND SINGLE LEVER LAVATORY FAUCET
662
SINGLE LEVER BIDET FAUCET
660/660-ND SINGLE LEVER LAVATORY FAUCET
662 SINGLE LEVER BIDET FAUCET
HANDLE OPERATION
Single Lever Lavatory/ Bidet Faucet
ROUGH-IN DIMENSIONS
Lift the handle gently. Turn clockwise for hot water, counter-clockwise for cold water.
1045050A-D 1
1045050A-D 4
Single Lever Lavatory/ Bidet Faucet
**Color code must be specified when ordering
INSTALLATION INSTRUCTIONS
SERVICE PARTS
Ø54
Ø32
Ø36.5
Ø31.75
108
98
176.5
94
Min
40
98
60
109
Wall
G1/2˝
G1/2˝
102
Min
40
98
50
27°
109
(500 for india)
400
(500 for india)
400
Max.45
Max.45
Wall
660/660-ND 662
834753**
Pop Up Drain
(Not for 660-ND)
880037
Link Kit
1080817
O-ring
880406
Washer
880008**
Stopper
871472
O-ring
(Only for 660IN)
Hose Assy
834705**
Screw Plug
833438
Screw
3006660
Valve Nut
1068079
Valve
836664
Mounting
Hardware Kit
3010479**
Lever
836628**
Ball Join
(Only for 662)
834769**
Aerator
(Only for 662)
Aerator
3002551**
Lift Rod Assembly
(Not for 660-ND)
3008414
Seat
(Only for 660IN)
Hose Assy
Aerator
660IN 662IN 660IN-ND
1024405 1024405 1024405
834562** 834769** 834562**

1045050A-D 2
1045050A-D 3
Assemble thumb screw(21) to link(20), and link onto ball lever(18)
with ‘V’-clip (19). Slide lift rod(5) into the hole in link. Push the ball
lever down into the open position, and adjust the lift rod. Tighten
thumb screw(21).
CLEANING INSTRUCTIONS
INSTALLATION CHECKOUT
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
Ensure that all connections are tight. Ensure that the handle is in the
off position.
Open the drain. Turn on main water supply and check for leaks.
Repair as required.
Remove aerator assembly(22). Turn the faucet handle on and run hot
and cold water through spout for about one minute to remove any
debris. Remove any debris from aerator assembly. Shut faucet off
and reinstall areator assembly.
3
4
5
INSTALLATION
How To Install The Faucet
Install the mountings stud(2) into the faucet body base(3). Insert lift
rod(5)(Not for 660-ND) into hole at rear of body assembly. Slide
O-ring(4) into groove on body assembly. Insert the flexible supply
hoses(1) into the hole from under the lavatory and install the flexible
supply hoses into the faucet holes. Tighten it by hand.
From underside of lavatory, place bracket(6) and nut(7) onto
mounting stud(2). Position faucet so that lift rod(5) is toward the back.
Tighten nut to secure faucet to lavatory.
Attach the hoses to water supplies. When facing front of faucet, the
left hose is hot water, the right hose is cold water.
How To Install The Drain (Not for 660-ND)
Remove stopper(14), flange(8) and washer(10) from drain body(9).
Take off the tailpiece(11). Apply thread tape to tailpiece and install the
tailpiece to drain body. Insert drain body kit into the lavatory from
underside, and make sure the drain lever hole(12) facing to the back
of the lavatory. Screw the flange with washer into the drain body.
Tighten the locknut(13) by hand from the underside of the fixture.
NOTE: If needed, apply a ring of plumbers putty around the
underside of the drain flange(8), instead of using washer(10).
Place stopper(14) into drain body aligning the flat side of stopper
hole(15) with the drain lever hole.
Remove the retaining nut(16). Fit the plastic washer(17) and retaining
nut onto the ball lever(18). Insert the ball lever assembly into the drain
lever hole and through the stopper hole. Tighten the retaining nut.
Be sure that the ball lever(18) points to the back of the lavatory,
tighten the locknut(13) on the drain body by wrench.
NOTE: Do not reposition the drain if plumbers putty applied after the
locknut is tightened, or you may break the putty seal. Wipe away
excess plumbers putty.
22
8
10
13
14
15
10
11
12
8
9
13
16
17
19
18
18
20
19
21
5
2
6
7
1