Kohler ARTIFACTS 72762T-9M User manual

1271109-2A-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
3. Observe local plumbing codes.
4. If possible, install this faucet before installing the lavatory.
5. Shut off the water supplies to the fitting.
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, counter-clockwise for cold water.
INSTALLATION INSTRUCTIONS
72762T-9M Single-handle Bathroom Sink Faucet
ARTIFACTS
72762T-9M Single-handle Bathroom Sink Faucet
ARTIFACTS
ROUGH-IN DIMENSIONS
1271109-2A-A 4
SERVICE PARTS
188~200
Ø69
Ø60
Ø41.2
27~60
Ø31.75
112
75MAX
176
144
97
52
516
Ø68
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
1271397
52202
78150
1146748
1228834
1006815
38820
1192902**
1192910**
1194613
1244853**
1272333**
38676
1181649**
1233282
1142103**
1102890**
1102891
1102892
1271187
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS

1271109-2A-A 2 1271109-2A-A 3
INSTALLATION
How to Install the Spout
Install the washer(2) into the bottom of faucet(3).
Insert hoses(4) and stud(1) into the hole of lavatory.
From underside of the lavatory, fit the bracket(5) onto
the stud. Position the faucet. Install the washer(6) and
nut(7) onto the stud, tighten the nut by tool(8) to
secure the faucet.
Attach the hoses to water supplies, the hose with
“COLD” label connects to cold water.
Ensure that all coupling nuts are tight. Ensure that
the lever handle is in the off position.
Turn on the main water supply and drain, and check
for leaks. Repair as needed.
Remove the aerator kit(16) by hand. Run hot and
cold water through faucet for about one minute to
remove any debris. Check for leaks. Repair as
needed. Remove any debris from the aerator. Shut
off the faucet. Reinstall the aerator.
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
3
2
1
4
7
5
6
8
How to Install the Drain
Remove the locknut(15), plastic washer(14) and the
rubber gasket(13) and tailpiece(12) from the drain
body(11).
Supply enough tape or sealant to tailpiece thread.
Reinstall the tailpiece.
Insert the drain body into the lavatory. Install the
rubber gasket(Tapered side up), plastic washer and
locknut back to the drain body in turn. Tighten the
locknut.
NOTE: If needed, apply a ring of plumbers putty or
other sealants around the underside of the drain
flange(9), instead of using rubber washer(10).
Do not reposition the drain after the locknut is
tightened, or you may break the putty or sealant
seal. Remove any excess putty.
9
10
11
12
13
14
15
16