Kohler TAUT 26259T-4 User manual

1439190-T2-A 1
安装说明书
安装之前
26259T-4 高抛单把感应厨房龙头
安装尺寸
韬立
TAUT
所有的资料是按最新出版的产品资料编写而成。科勒公司保留任何时候不经通知即可改变产品特性、包装或产
品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，请把这些资料交给用户阅读。
注意事项：
1.一定要先彻底冲洗供水管以清除管道中的杂质。
2.如果是安装新的厨盆，可将水龙头先装到厨盆上。
3. 人身损害或财产损坏风险。开始安装前，请从头到尾阅读产品说明。
4. 严格遵守一切管道铺设、电气和建筑规范。
5. 淡水污染风险。这个水龙头有反虹吸保护装置。切勿拆下任何内部部件。
6.产品损坏风险。本产品含有敏感的电子元件。切勿将打开的化学或清洁产品容器存放在本产品附近。
7.留出足够的维修空间：
①安装水龙头之前，确保厨盆下面的区域能够容纳所有需要的组件。
②考虑后续步骤中涉及到的连接，确保支架位置留有足够的空间。
单位：毫米
324
233
182
22º
Ø34~Ø37
600
Ø45
G1/2˝
64
146
550
50 最大
110

使用说明
龙头操作
□向外旋转把手至打开位置，如电子阀已开启，则龙头自动出水；如电子阀未开启，则龙头不出水，需挥手感
应开启电子阀。持续4分钟不操作后，龙头出水自动关闭，需重新挥手感应开启龙头出水。
□调节把手至所需水温。
□伸手在传感器旁边再次挥动以关闭出水。
注意：
□长时间不使用时，应将把手旋转回关闭(直立) 位置。
□传感器需远离蒸汽。
□请勿在传感器正对面200mm以内放置任何物品，以免误触发感应和电耗损。
电子阀LED灯指示说明
□绿色LED：表示已安装并连接交流插头。
□红色LED闪烁：表示电池电量不足。
特征
□自动关闭：闲置4分钟后，会自动关闭出水。
手动操作
□在断电的情况下，感应功能将失效，可以手动操作电子阀上的手动操作阀杆。
□用硬币顺时针转动手动操作阀杆到位启动手动操作功能，逆时针转动到位关闭手动操作功能。
□一旦打开手动操作功能，水龙头仅能通过手动控制。
传感器 开启位置
手动操作阀杆
1439190-T2-A 2
>200mm

安装步骤
如何连接软管
□如图所示，将供水软管(8)拧紧到供水管上，蓝色
条纹的软管连接冷水，红色条纹的软管连接热水。
□打开冷热水源及龙头把手，让水流出约一分钟左
右，清除管道中的杂质，然后关上把手及冷热水
源，
注意：安装过程中，供水软管不得绷紧、打结或缠
绕。如不得不盘绕，则保持不小于Ø76mm的内径。
如何安装水龙头
□将固定螺栓(1)装入龙头本体(2)底部。将垫片(3)穿
过软管和固定螺栓嵌入到水龙头本体底部凹槽中。
□将龙头组件插入厨盆安装孔中，使垫片底部接触台
面。
□从厨盆下方将垫片(4)套入软管和固定螺栓，接着
将垫片(5)(橡胶垫片放在上面)和螺母(6)套入固定螺
栓。
□调整水龙头至合适的位置，用工具(7)锁紧螺母。
以固定龙头。
支架
3M双面胶
方式二
用于墙面安装
用于薄板上安装
支架
方式一
如何安装支架
注意：①支架必须水平安装。②留出足够的维修空
间。
□安装方式一：锁紧螺钉以固定支架。
□安装方式二：仅适用于平整、光滑的墙面。
①清洁支架背面及墙面被贴位置，去除油污、水渍以
及灰尘等；
②待表面干燥后，撕开3M双面胶一面的离型纸，贴
于支架的背面，贴合后均匀按压一会；
③撕开双面胶另一面离型纸，在保证支架方向及水平
位置后，将支架粘贴在墙面上，按压使其牢固贴合。
Ø76mm最小
8
1439190-T2-A 3
1
5
4
2
3
6
7

安装结果检查
如何安装电子阀
重要！限流风险。安装过程中，出水软管(9)不得绷
紧或打结。
注意：用手拧紧出水软管接头。不要使用钳子或扳
手。
□将出水软管(9)拧到电子阀进水口(10)。
□将电子阀(11)套在已安装好的支架上。
□将软管(12)连接到电子阀出水口(13)。确保卡入到
位，连接牢固。
如何连接电线
□连接蓝色接头到电子阀上的蓝色端口。接头上的
白色标记须朝前方。
注意：电子阀所有电线连接完成后，需等待15秒才
能开始工作。
□检查并确保所有衔接处都已拧紧。
□确保把手在关闭位置。
□打开主水源和排水系统。
□检查并修理有漏水的接口。
□将起泡器取下。打开水龙头，让水流约一分钟以
清除杂质。冲洗起泡器。关闭水龙头，重新装回起
泡器。
蓝色接头
蓝色端口
维护与保养
如何清洗电子阀进水滤网
□关闭龙头。
□将出水软管(9)与电子阀(11)断开。
□从电子阀内部拆下并清洁进水滤网(14)。
□装回进水滤网，并重新连接出水软管。
9
14
11
9
10
11
支架
12
13
白色标记
1439190-T2-A 4
花洒软管
电子阀
蓝色端口和接头
出水软管
供水软管
供水阀
起泡器

故障检修
龙头故障检修表
警告：产品损坏风险。本产品含有敏感的电子元件。在故障排除过程中，小心不要损坏销子和接头。
故障现象 可能的原因 推荐解决方式
A. 供水阀关闭。
B. 龙头把手处于关闭位置。
C. 冷和/或热供水软管缠绕打结。
D. 电池电量不足或耗尽。
E. 电子阀滤网堵塞。
A. 供水阀部分关闭。
B. 龙头把手部分关闭。
C. 冷和/或热供水软管缠绕打结。
D. 一个或多个滤网堵塞。
E. 隔膜片破裂。
A. 打开供水阀。
B. 转动把手至打开位置。参考“使用说明”。
C. 确认供水软管没有缠绕打结。如盘绕，则保持不小
于Ø76mm的内径。
D. 检查传感器上的LED灯是否红色闪烁。如果出现闪
烁，参考电子阀说明书1441903-2更换电池。
E. 参考“维护与保养”。
A. 确认供水阀完全打开。
B. 转动把手至完全打开位置。
C. 确认供水软管没有缠绕打结。如盘绕，则保持不小
于Ø76mm的内径。
D. 参考“维护与保养”。
E. 更换电子阀组件。
A. 起泡器堵塞。 A. 取下起泡器，打开龙头，清洗起泡器，清除杂质。
1. 产品不出水。
2. 出水量小。
3. 出水效果差。
4. 水龙头不使用
时滴水或滴漏。
A. 手动操作功能部分接入。 A. 用硬币逆时针转动电子阀上的黑色硬币口直至拧不
动，然后顺时针转动直至滴漏停止。
龙头本体背面标有“LEAD FREE”字样，即产品符合美国AB1953法令的要求。
清洗说明
适用于所有加工处理过的表面：以中性肥皂水清洗镀层表面，再以干净软布彻底擦干整个表面，许多清洁剂，
比如氨水、去污粉及洁厕灵等，会对电镀表面造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌的水龙头及其配件上。
1439190-T2-A 5

1439190-T2-A 6
服务零件
**订购时请说明颜色编号
韬立
TAUT
26259T-4 高抛单把感应厨房龙头
1209778**
1209777
1441910
1441911
1228834
1474445
1441909
1441907
1176162
1377106
1410195
1292054
1243532** 1309847**
833438
833730
3008523
1455660
1128531
1455651
836549
1031238
3002868
1441898
836589
1441912

26259T-4 Touchless Swing Kitchen Faucet
INSTALLATION INSTRUCTIONS
TAUT
BEFORE YOU BEGIN
ROUGH-IN DIMENSIONS
All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right
to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTE:
1. Flush the water supply pipes thoroughly to remove debris.
2. For new installations, install the faucet to sink before installing.
3. Risk of injury or property damage. Please read all instructions thoroughly before beginning installation.
4. Follow all plumbing, electrical, and building codes.
5. Risk of fresh water contamination. This faucet contains back-siphonage protection. Do not remove any internal
components.
6. Risk of product damage. This product contains sensitive electronic components. Do not store open containers of
chemical or cleaning products near this product.
7. Allow adequate clearance for servicing.
1) Before installing the faucet make sure the cabinet area under sink can accommodate all of the required components.
2) Consider loose fitting the connections covered in the following steps to make sure the bracket location allows enough
clearance.
1439190-T2-A 1
Unit: mm
324
233
182
22º
Ø34~Ø37
600
Ø45
G1/2˝
64
146
550
50 Max.
110

Faucet Operation
□Rotate the handle outward to the open position. If the valve is turned on, it will start water flow automatically. If not, it will
not start water flow, wave your hand near the sensor to turn on the valve. After 4 minutes of inactivity, the water will
automatically shut OFF, wave your hand near the sensor again to turn the water ON.
□Adjust the handle to the desired water temperature.
□Wave your hand near the sensor again to turn the water OFF.
NOTE:
□For extended periods of nonuse, the handle should be returned to the closed (upright) position.
□Keep the sensor away from the steam.
□Do not place anything within 200mm from the sensor to avoid accidentally activating the sensor and power consumption.
Valve Box LED Indicators
□Green LED: Indicates that the AC plug is installed and connected.
□Red flashing LED: Indicates low batteries.
Features
□Automatic shut-off: After 4 minutes of inactivity, the water will automatically shut OFF.
Manual Sensor Override
□In case of power loss, the sensor function can be bypassed by engaging the manual override feature on the valve box.
□Turn clockwise to engage the bypass and counter-clockwise to disable the bypass with coin.
□Once the manual override is engaged, the faucet can then be operated manually only.
OPERATION INSTRUCTION
Manual Override Stem
1439190-T2-A 2
Sensor Open Position >200mm

INSTALLATION
Ø76mm Min.
Bracket
3M Double
sided Tape
Way 2
For Dry Wall
For Sheet
Bracket
Way 1
How to Install the Faucet
□Install the mounting stud(1) into the faucet body(2)
base. Slide the washer(3) into the groove of the body
through the hoses and mounting stud.
□Insert the faucet assembly into the mounting hole.
Ensure the bottom of the washer is against the deck.
□From underside, slide the washer(4) onto the hoses
and mounting stud, and then place the washers(5,
rubber washer is on the top) and nut(6) onto the
mounting stud.
□Adjust the faucet to a suitable position, tighten the nut
with tool(7) to secure the faucet.
How to Connect the Hoses
□Tighten the supply hoses(8) onto water supplies. The
hose with blue mark should be connected to cold water.
The hose with red mark should be connected to hot
water.
□Open hot and cold water supplies. Turn on the faucet.
Flush hot and cold water for about one minute to
remove any debris. Shut off faucet and water supplies.
NOTE: Supply hoses must not be taut, kinked, or
twisted during installation. If the supply hoses must be
coiled, maintain an inside diameter of minimum Ø76mm.
How to Install the Bracket
NOTE: 1) The bracket must be installed horizontally.
2) Allow adequate clearance for servicing.
□Way 1: Secure bracket with provided mounting screws.
□Way 2: Only apply for flat and smooth walls.
1) Clean the bracket backside and installed location of
the wall. Be sure to remove oil, water and dust.
2) After the surface is dry, tear off one paper of the 3M
double sided tape, stick it on the bracket backside, and
press it evenly for a while after bonding.
3) Tear off another paper of the 3M double sided tape.
Ensure the bracket is horizontal and in the right place,
and then paste it onto the wall and press it firmly.
1439190-T2-A 3
8
1
5
4
2
3
6
7

9
10
11
12
13
9
14
11
How to Connect the Wires
□Connect the blue connectors to the blue terminals on
valve box. The white lines on the connectors should face
the front of the valve box.
NOTE: After all wires of the valve box are connected, it
will take 15 seconds to start working.
How to Install the Valve Box
IMPORTANT! Risk of restricted waterflow.
The outlet hose(9) must not be taut or kinked when
installed.
NOTE: Tighten the outlet hose connector by hand.
Do not use a pliers or a wrench.
□Thread the outlet hose(9) onto the valve inlet(10).
□Slide the valve box(11) into the mounted bracket.
□Connect hose(12) to the valve box outlet(13). Make
sure it is securely connected in place .
□Ensure that all connections are tight.
□Ensure that the handle is in the off position.
□Turn on the main water supplies and drain.
□Check all connections for leaks. Repair as needed.
□Remove the aerator. Turn on the faucet, run hot and
cold water about one minute to remove any debris.
Remove any debris from the aerator. Shut off the faucet.
Reinstall the aerator.
How to Clean Inlet Screen of Valve Box
□Turn the handle to the closed position.
□Disconnect the outlet hose(9) from the valve box(11).
□Remove and clean the inlet screen(14) from inside the
valve box.
□Reinstall the inlet screen and reconnect outlet hose.
Supply Hose
Aerator
Supply Stop
Blue Terminals
& Connectors
Hose
Valve Box
Outlet Hose
Blue Connectors
Blue Terminals White Lines
Bracket
CARE AND MAINTENANCE
INSTALLATION CHECKOUT
1439190-T2-A 4

TROUBLESHOOTING
Faucet Troubleshooting Table
CAUTION: Risk of product damage. This product contains sensitive electronic components. Use care not to damage
pins and connectors during troubleshooting.
A. The supply stops are closed.
B. Handle is in the closed position.
C. The hot and/or cold supply hose is
kinked.
D. Battery power is low or exhausted.
E. Valve screen is clogged.
Symptoms Probable Causes Recommended Actions
1. No water flow.
2. Low water flow.
3. Poor spray
pattern.
A. The aerator is clogged. A. Remove the aerator. Turn on the faucet and run hot and
cold water to remove any debris from the aerator.
4. Water drip or
trickle when faucet
is not in use.
A. Manual override is partially engaged. A. Turn the manual override counter-clockwise as far as
possible. Then turn the manual override clockwise until
the water stops dripping.
A. Confirm the supply stops are open.
B. Rotate the handle to the open position. Refer to the
″Operation Instruction″ section.
C. Confirm the supply hoses are not kinked. If coiled,
maintain an inside diameter of minimum Ø76mm.
D. Check for a red flashing LED on the sensor. If it flashes
red, refer to valve box installation instruction 1441903-2
for batteries replacement.
E. Refer to the ″Care and maintenance″ section.
A. Confirm the supply stops are fully open.
B. Rotate the handle to the full open position.
C. Confirm the supply hoses are not kinked or twisted.
If coiled, maintain an inside diameter of minimum Ø76mm.
D. Refer to the ″Care and maintenance″ section.
E. Replace the valve box assembly.
A. The supply stops are partially closed.
B. Handle is partially closed.
C. The hot and/or cold supply hose is
kinked or twisted.
D. One or more screens are clogged.
E. Cracked diaphragm.
"LEAD FREE" is marked on the back of the faucet signifying its compliance with the United States AB1953
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft cloth.
Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely affect the
finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
1439190-T2-A 5

26259T-4 Touchless Swing Kitchen Faucet
SERVICE PARTS
TAUT
**Color code must be specified when ordering.
1439190-T2-A 6
1209778**
1209777
1441910
1441911
1228834
1474445
1441909
1441907
1176162
1377106
1410195
1292054
1243532** 1309847**
833438
833730
3008523
1455660
1128531
1455651
836549
1031238
3002868
1441898
836589
1441912