Kohler Renew 76881T-E User manual

1273668-AN2-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Observe local plumbing codes.
2. An inline water filter must be used with this product.
3. The highest working pressure for handshower is 0.5MPa(5 bar). If it exceeds 0.5MPa(5 bar), a pressure reducer
is needed. The highest water and environment temperature is 60°C. Please keep handshower, showerhead and
the shower arm away from heater, or it may become damaged and cause injury to the user.
4. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.
1273668-AN2-A 4
INSTALLATION INSTRUCTIONS
76881T-E Slide Shower-Geometric
76882T-E Slide Shower-Organic
RENEW
76881T-E Slide Shower-Geometric
76882T-E Slide Shower-Organic
RENEW
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering.
1500
560~660
58
700~800
75
60
1248781**
76882T-E:1236561**
23096
1208176**
76881T-E:1236560**
1195838**
1081607
1269272**
1061576
1208178
1219396**
1208177**
51 59
44
58
38
G1/2˝
G1/2˝
G1/2˝
G1/2˝
Only for 76881T-E
Only for 76882T-E
1194751**
1128483
Ø110
Ø110
G1/2˝
G1/2˝
249
243
252 260
1240266
1030624
1208178
1061576
23096

1273668-AN2-A 2 1273668-AN2-A 3
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Handshower and Hose
Flush both water supplies for about one minute before
the handshower(18) is installed. Attach the
handshower to shower hose(17). NOTE: Don’t over
tighten.
Connect another end of shower hose to the outlet(14)
of the connection.
Hang the handshower in the bracket(4).
How to Install the Slide Bar
Decide on a suitable position for the slide bar avoiding
buried cables and pipes in the wall.
Drill two holes at the proper height on the finished wall
according to the rough-in dimensions and should
match the anchors(1).
Put anchors into the holes. Install the upper and under
base(2) with screws(3) in the wall.
Place the bar(5) into the under slide bar body(6).
Install the screw(7), tighten them by hex wrench(8).
Slide the handshower holder(4) onto the bar. The
height of handshower holder can be adjusted by
pressing the pinch cock(9) and sliding up and down.
Adjust it to the proper position.
Tighten the screw(7) to secure upper slide bar
body(10) by hex wrench according to the rough-in
dimensions. Make sure the directions of the upper and
under slide bar body are consistent.
18
17
How to Operate the Handshower
Rotate the knob of the handshower to change the water
flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause the flow
stream to become distorted or reduce the flow rate. To
remove the debris or mineral build-up, run water
through the handshower, firmly press or rub your finger
back and forth across the rubber nozzles.
560~660
3
7
2
10
1
7
5
6
4
9
8
How to Install the Connection Kit
Before installation, installer must provide G1/2″ supply
fitting(13). Ensure it extend 12~20mm beyond the
finished wall.
Apply tape or thread sealant to G1/2″ threads of the
supply fitting. Apply a ring of plumber putty or other
sealants around the underside of the connection
kit(16). Install the connection kit onto the supply fitting.
Adjust the connection kit and make sure the outlet(14)
and drain notch(15) of the escutcheon downwards.
Remove any excess putty.
①
②
13
16
15
14
12~20mm
Slide the bracket escutcheons(11) onto the bases(2),
confirm the drain notch of the escutcheon is pointed
down. Install the whole slide bar onto the bases.
Tighten the screws(12) by hex wrench to secure the
slide bar.
12
Drain notch
11
11
12
2
③
Drain
notch