Kohler K-8002 User manual

Installation Guide
Bodyspray Tile
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-8002 K-8003
1043851-2-D

Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
Observe all local plumbing and building codes.
Inspect the supply piping for damage. Replace as necessary.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
5/64" & 3/16"
Hex Wrenches
Socket Wrench with 11 mm or
7/16" Socket and Extension
Sealant
Tape
Plus:
• Close nipple or
• 1-1/2" NPT pipe nipple
• 1/2" NPT female fittings
• 1/2" copper pipe
Phillips
Screwdriver
Masking
Tape
1043851-2-D 2 Kohler Co.

1. Install the Supply Piping
Multiple Bodyspray Installations
Route the water supply lines.
If installing more than one bodyspray off the same supply line,
construct a pressure balancing loop. Locate a tee along the loop at
each bodyspray installation location.
Do not strap the pipes at this time.
Single Bodyspray Installations
Route the water supply line.
Install an elbow to the end of the supply pipe at the bodyspray
installation location.
All Installations
Temporarily install a nipple to each tee/elbow. Do not use any
sealant.
Do not strap the pipes at this time.
Pressure
Balancing Loop
Water
Supply
Single Bodyspray InstallationMultiple Bodyspray Installation
Nipple Nipple
Kohler Co. 3 1043851-2-D

2. Install the Plaster Guard
Install the plaster guard. Push until the plaster guard is snug
against the face of the elbow (or tee).
3. Set the Pipe Depth
Thin Wall Installations
NOTE: Thin wall installations have a finished wall thickness of less
than 1/2″(1.3 cm).
To adjust the pipe depth, use a level or other straight edge to line
up the ″Thin Wall Installation″mark with the front face of the
studs.
Standard Wall Installations
To adjust the pipe depth, use a level or other straight edge to line
up the edge of the plaster guard with the front face of the studs.
All Installations
Install appropriate backing and strap the pipes at the adjusted
depth.
Elbow (or Tee) Thin Wall
Standard Wall
Set Piping DepthInstall the Plaster Guard
Install the
plaster guard.
Align mark with the
front of the stud face.
Align mark with the
front of the stud face.
1043851-2-D 4 Kohler Co.

4. Install the Finished Wall
Install the Wall Material
Install the water-resistant wall board.
Cut out a 4″(10.2 cm) to 4-1/4″(10.8 cm) square at each tile
installation location.
Install the finished wall material.
5. Verify Depth and Install the Nipple
Remove the nipple.
NOTE: The minimum distance between the face of the tee/elbow
and the surface of the finished wall should be 2-1/4″(5.7 cm). The
measurement for typical installations is 2-3/4″(7 cm).
Measure the distance from the face of the tee/elbow to the
surface of the finished wall. Make any adjustments as needed.
If your measurement is 2-1/4″(5.7 cm): Use a close pipe nipple.
If your measurement is 2-3/4″(7 cm): Use a 1-1/2″pipe nipple.
Thread the nipple into the tee/elbow and hand tighten.
Measure the distance from the end of the nipple to the surface of
the finished wall. Verify that the distance is at least 1-1/2″(3.8
cm) and no more than 1-3/4″(4.4 cm).
Remove the nipple.
Apply thread sealant to the threads of the nipple.
Reinstall the nipple to the tee/elbow.
Run water through the system to flush out any dirt or debris.
4" (10.2 cm) –
4-1/4" (10.8 cm)
4" (10.2 cm) –
4-1/4" (10.8 cm) 4" (10.2 cm) –
4-1/4" (10.8 cm)
Cutout
Nipple
Tee (or Elbow)
Finished Wall
Cutout 2-1/4" (5.7 cm) Min
Kohler Co. 5 1043851-2-D

6. Install the Waterway
Insert the escutcheon into the rough opening. The double ribs of
the leak shield should be facing up.
If the leak shield makes contact with the elbow: Enlarge the
hole in the back of the leak shield to 1-1/4″(3.2 cm).
Thread the adapter onto the nipple using the provided 11 mm bit,
11 mm or 7/16″socket, extension and socket wrench. Use
masking tape to hold the bit in place, as the bit could fall off and
cause damage.
IMPORTANT! The escutcheon should sit loosely at this point. If it is
tight against the wall, use a longer pipe nipple.
Align the groove in the waterway with the double ribs on the
leak shield.
Press the waterway into place over the adapter. Secure the
waterway to the adapter with the screw provided.
Verify that the escutcheon does not turn or shift.
IMPORTANT! If the escutcheon is still loose after this step, use a
shorter pipe nipple.
Waterway
Screw
Leak Shield
Escutcheon
Adapter
Socket Wrench
With Bit
Extension
1043851-2-D 6 Kohler Co.

7. Complete the Installation
Attach the Sprayhead
With the ribs of the sprayhead facing up, attach the sprayhead to
the waterway.
Using a 3/16″hex wrench, secure the sprayhead to the waterway
with the two hex screws provided. Do not overtighten.
Check the sprayhead for upward and downward movement and
that it sits squarely within the escutcheon.
Place the nozzle membrane over the sprayhead.
Align the long edge of the membrane with the hinge ribs
(horizontal).
NOTE: For optimum performance, ensure that the membrane is
applied evenly.
Applying pressure evenly, press the membrane seal into the
sprayhead groove.
Attach the Sprayface
NOTE: For product with brushed finishes, align the brush pattern of
the sprayfaces with the direction of the brushed pattern of the
escutcheon.
Tilt the sprayhead downward so the ribs on the top of the
sprayhead are exposed.
Insert the grooves of the sprayface over the ribs of the sprayhead.
Sprayface
Ribs
Ribs
Groove
Finished Wall
Setscrews
Sprayhead
Waterway
Hex Screws
Attach the Sprayhead Attach the Sprayface
Nozzle
Membrane
Kohler Co. 7 1043851-2-D

Complete the Installation (cont.)
Press the sprayface down to cover the sprayhead, as illustrated.
Tilt the sprayhead upward to expose the setscrew holes on the
bottom of the sprayhead.
IMPORTANT! The setscrews must be flush with the edge of the
sprayface frame. If the setscrews protrude outside of the sprayface
frame, product damage will occur.
Using a 5/64″hex wrench, turn the setscrews counterclockwise
until they are flush with the edge of the sprayface frame.
1043851-2-D 8 Kohler Co.

Guide d’installation
Carrelage jet corporel
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de performance. Nos numéros de téléphone
et notre adresse du site internet sont au verso. Merci encore d’avoir
choisi la compagnie Kohler.
Avant de commencer
Respecter tous les codes de plomberie et de bâtiment locaux.
Inspecter la tuyauterie d’alimentation de tout endommagement.
Remplacer si nécessaire.
Kohler Co. se réserve le droit d’apporter toutes modifications au
design des robinets et ceci sans préavis, comme spécifié dans le
catalogue des prix.
Clés
hexagonales
Clé à douille avec douille et
rallonge de 11 mm ou de 7/16"
Ruban
d'étanchéité
Plus:
• Mamelon étroit ou
• mamelon de tuyau de 1-1/2" NPT
• raccords femelles 1/2" NPT
• tuyau en cuivre de 1/2"
Tournevis
cruciforme
Ruban-cache
Kohler Co. Français-1 1043851-2-D

1. Installer la tuyauterie d’alimentation
Installations de jets corporels multiples
Acheminer les lignes d’alimentation d’eau.
Si plus d’un jet corporel d’une même ligne d’alimentation est
installé, construire une boucle de régulation de pression. Localiser
un T le long de la boucle à chaque emplacement d’installation de
jet corporel.
Ne pas attacher les tuyaux à ce moment.
Installations d’un seul jet corporel
Acheminer la ligne d’alimentation d’eau.
Installer un coude à l’extrémité du tuyau d’alimentation à
l’emplacement d’installation du jet corporel.
Toutes les installations
Installer temporairement un mamelon à chaque T/coude. Ne pas
utiliser de mastic.
Ne pas attacher les tuyaux à ce moment.
Boucle de
régulateur
de pression
Alimentation
d'eau
Installations d'un
seul jet corporel
Installations de jets
corporels multiples
Mamelon Mamelon
1043851-2-D Français-2 Kohler Co.