Kohler PURIST 7505T-B4 User manual

1230970-2A-D 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. For new installations, assemble the faucet to sink before installing.
3. The highest working pressure for handspray & shower head is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a
pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handspray,
shower head and the shower arm away from heater, or it may become damaged and cause injury to the user.
HANDLE OPERATION
Open the handle gently. Turn clockwise for cold water, counter-clockwise for hot water.
1230970-2A-D 4
INSTALLATION INSTRUCTIONS
7505T-B4 Single Hole Kitchen Faucet7505T-B4 Single Hole Kitchen Faucet
PURISTPURIST
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering
616
93
139
1700
63
G1/2˝
757
MAX 63.5
Ø33~Ø42
203
226
290
1153137**
101131
1048075
1066106
84100
1128531
1115287
58946
833438
1232536
1099016**
1151299
1150881
1229445
1046153
1217943
880096
1148476**
22352
1036389
1104495
29296
1166882
1243258**
834705**
1130269
1016503

1230970-2A-D 2 1230970-2A-D 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Faucet
Slide the o-ring(1) into the groove of the bottom of the body(2). Put the
hoses and the shank(3) into the mounting hole of the sink. Let the bottom
of the body against the deck.
Screw two screws(4) into the threaded ring(5). From underside of the
sink, place the metal washer(6) and the threaded ring with two screws
onto the shank. Position the faucet so that the hose(7) is on the left, the
spray hose and two hoses(8) are symmetrical. Tighten two screws(4) to
secure faucet to sink.
Attach the hoses to water supplies. When facing the faucet, the hose in
front connects to hot water, the back hose with ‘COLD’ label connects to
cold water.
Put the weight(10) and clip(11) onto the hose(7). Adjust the weight so
that the distance is right from the bottom of the faucet to the weight.
Insert the hose(7) into the connector(9).
Ensure that all coupling nuts are tight. Ensure that the lever handle is in
the off position.
Turn on the main water supply and drain, and check for leaks. Repair as
needed.
Remove the spray(12). Remove the aerator(14) with the key(13). Turn on
the faucet. Run hot and cold water about a minute to remove any debris.
Remove any debris from the filter washer and aerator. Shut off the faucet.
Reinstall the aerator and spray.
How to Use Spray
Open the handle, if you want to use the spray by hand, take the spray
and pull out the hose.
Press the button(A) as shown for figure(a) form of water flow. Press the
button(B) as shown for figure(b) form of water flow, press the button(B)
again for the water close.
NOTE: Please pull it gently and do not draw out the spray hose too long,
or you may damage the hose and connector.
12
13
14
B
A
b
a
8
2
1
6
5
4
79
10
11
3
"LEAD FREE" is marked on the back of the faucet signifying its compliance with the United States AB1953