Kohler PURIST 14406 User manual

1049310-2A-A 1
BEFORE YOU BEGIN
1049310-2A-A 4
INSTALLATION INSTRUCTIONS
14406 8″ Widespread Lavatory Faucet
14408 8″ Widespread Tall Lavatory Faucet
14406 8″ Widespread Lavatory Faucet
14408 8″ Widespread Tall Lavatory Faucet
PURISTPURIST
HANDLE OPERATION
ROUGH-IN DIMENSIONS
SERVICE PARTS
All information is based on the latest product information available at the time of publication.
Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time
without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. If possible, install this faucet before installing the lavatory.
Left handle opens with one-quarter turn counter clockwise. Right handle opens with one-quarter turn clockwise
(Lever Handle).
Left handle opens with one-quarter turn clockwise. Right handle opens with one-quarter turn counter clockwise
(Corss Handle).
Handle Selection
Ø32MIN
45MAX
Ø13
A
B
D
E
C
155~440
G1/2″
76 55
25
G1/2″
Ø50
Ø50 Ø50
Cross Handle
(14406-3/3ND)
(14408-3)
Lever Handle
(14406-4/4ND)
(14408-4)
14406 127 148 216 90 92
A B C D E
14408 140 221 291 126 128
**Color code must be specified when ordering
78125
Spline Adapter
40013
Gasket
3006312
O-Ring
Valve
1008705
Dished Washer
1047530
Gasket
830915
Washer
40015
Washer
40097
Washer
1112775
Hose
864342
Nut
40014
Nut
1017818
Shank
1077948**
Aerator Kit
1060036**
(Only for Thailand)
1012840
Stem Extension
(Only for 14408)
3002641
Screw
(Only for 14408)
1009889**
Cross Handle
1009890**
Lever Handle
1013347**
Lift Rod Assy
(Not for 14406-3ND/4ND)
1059036-C**(right)
1059036-H**(left)
High Cross Handle Kit
(Only for 14408-3)
1059037-C**(right)
1059037-H**(left)
High Lever Handle Kit
(Only for 14408-4)
1059034-C**(right)
1059034-H**(left)
Cross Handle Kit
(Only for 14406-3)
1059035-C**(right)
1059035-H**(left)
Lever Handle Kit
(Only for 14406-4)
91640
O-Ring
SKU Handle Velve(left) Velve(right) Handle Kit
14406-3** 1009889** 835749 835749 1059034**
14406-4** 1009890** 835749 835750 1059035**
14408-3** 1009889** 835749 835749 1059036**
14408-4** 1009890** 835749 835750 1059037**
880062
Side Body Assy
1046513
Centre Tee
1049172
Tee Assembly
Ø54
Ø32
Ø36.5
Ø31.75
108
98
176.5
880037
Link Kit
1080817
O-ring
880406
Washer
880008**
Stopper
834753**
Pop Up Drain
(Not for 14406-3ND/4ND)
1176997
Link Kit

1049310-2A-A 2 1049310-2A-A 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
1
2
3
4
5
6
7
How to Install the Spout
Remove and retain the parts from the spout kit(1) according to the follow-
ing order: nut(3) and metal washer(2).
Install the O-ring(7) to the bottom of the spout through the shank.
Fit the spout to the center hole of lavatory. Install the metal washer and
nut. Adjust the position of the spout and securely tighten nut.
Thread the supply tee(6) with plastic gasket(5) and rubber washer(4) to
the spout shank, tighten by hand.
How to Install the Valve Bodies, the Handles
and the Hoses
Remove the handle kit(8) from the side body(9). Install the sticker
washer(10) into the groove on the bottom of the escutcheon(13).
Put the washers into the ends of the hose(14). Connect the side bodies
and supply tee(6) with hoses as shown in the figure.
NOTE: The hoses(14) should only be used here.
Insert the side body with dished washer (17), washer(11)and nut(12)
through mounting holes from bottom of the lavatory(For 14406T-4 and
14408T-4, the side body with red mark on the left when facing the front of
the faucet). Press the spline adapter(15) onto the valve stem(16).
Reinstall and tighten the handle kit(The handle with the red washer on
the left when facing the front of the faucet). Tighten the nut(12).
The configuration shown is the correct position of the handles in the
closed position.
8
9
14
11 12 17
14
9
6
13
10
15
16
34
Ensure that all connections are tight. Remove the aerator(34).
Open the drain. Turn on the main supply and check for leaks. Open both
hot and cold valves and run water through the spout to remove any
debris. Turn the valve off. Reinstall the aerator.
How to Install the Drain
Remove the stopper(18), flange(20) and washer(21) from the drain
body(23). Take off the tailpiece(25). Apply thread tape to the tailpiece
and install the tailpiece to drain body. Insert the drain body kit into the
lavatory from underside, and make sure the drain lever hole(22) facing to
the back of the lavatory. Screw the flange with washer into the drain
body. Tighten the locknut(24) by hand from underside of the lavatory.
NOTE: If needed, apply a ring of plumbers putty around the underside of
the drain flange(20), instead of using washer(21).
Place the stopper(18) into the drain body aligning the flat side of stopper
hole(19) with the drain lever hole.
Remove the retaining nut(29). Fit the plastic washer(27) and retaining nut
onto the ball lever(28). Insert the ball lever assembly into the drain lever
hole and through the stopper hole. Tighten the retaining nut.
Be sure that the ball lever(28) points to the back of the lavatory, tighten
the locknut(24) on the drain body by wrench.
NOTE: Do not reposition the drain if plumbers putty applied after the
locknut is tightened, or you may break the putty seal. Wipe away excess
plumbers putty.
Insert lift rod(30) to the hole at the rear of the body(33). Assemble the
thumb screw(31) to the link(32), and link onto the ball lever(28) with
“V”-clip (26). Slide the lift rod(30) into the hole in link. Push the ball lever
down into the open position, and adjust the lift rod. Tighten the thumb
screw(31).
20
21
24
18
19
21
25
22
20
23
24
29
27
26
28
28
32
26
31
30
30
33
10mm