Kolpin Outdoors 34-0050 Installation and operating instructions

© 2017 Kolpin Outdoors Inc. REV 03
ALL MOUNT
UNIVERSAL UTV PLOW MOUNT KIT
P/N 34-0050
ASSEMBLY / OWNERS MANUAL
Application
PLOW PUS FRAME NO. 34-0000 or 34-0070
Before you begin, please read these instructions and check to be sure all parts and tools are ac-
counted for. The following instructions contain details required to install and service the contents of
this kit.

2
© 2017 Kolpin Outdoors Inc. REV 03
OPERATING INSTRUCTIONS
Congratulations! You’ve just purchased the most durable plow component in the industry. Kolpin plow components work great for
summer or winter plowing. With proper care and maintenance, your Kolpin plow system will last for years to come!
NOTICE
Plow oper tion requires
ddition l components for oper tion: Kolpin Plow
Push Frame, High Rise Plow Push Frame, Winch Kit
*
Please read and understand all assembly instructions, notices and warnings before assembling and operating your Kolpin plow
system.
Follow these guidelines to ensure s tisf ctory oper tion:
• Read this manual and your ATV/ UTV operators manual before use.
• Periodically check for wear and tightness of all fasteners. Replace or re-torque fasteners as necessary.
• Before first use, set plow in the furthest right or left angled position to check for interference with the vehicle.
• Operate with extreme caution on slopes and rough terrain. Be familiar with the area before you plow.
• Be aware of immovable objects that could be hidden in the area you are plowing.
• To avoid damage when pushing snow into a pile, reverse direction before raising the plow blade.
• Do not ram the plow blade into piles of snow.
• For best results, set the suspension preload of your ATV/ UTV to the stiffest setting.
• To reduce steering effort and increase mobility, set the air pressure of your tires to the maximum pressure specification.
• The plow skids are adjustable. General skid setting is even with the plow wear bar bottom edge, higher settings reduce the
chance of rocks and gravel from being collected.
• To increase traction during plow operation, operators can try: Securing weight to the ATV/ UTV for additional tire downforce,
reducing tire air pressure, or installing tire chains.
SAFETY INFORMATION
Our plow systems were designed with your safety in mind. Please read and understand all Cautions, Notices and Warnings in this
manual before you begin. In order to protect you and your ATV/UTV, certain parts of the plow system and/or hardware are designed to
fail when the equipment is over-stressed.
DANGER
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT EXCEED 5 MPH (8 KMH) WITH BLADE INSTALLED.
2. OPERATE WITH EXTREME CAUTION ON SLOPES, STEEP GRADES, AND ROUGH TERRAIN.
3. ALLOW NO RIDERS ON BLADE OR ATV/UTV WHILE MOVING OR STATIONARY.
4. KEEP BYSTANDERS AWAY FROM THE BLADE OR ATV/UTV WHILE MOVING OR STATIONARY.
5. WHEN PUSHING HEAVY MATERIAL, DIRECTION CONTROL MAY BECOME DIFFICULT.
6. BEFORE ADJUSTING BLADE: STOP ATV/UTV ENGINE; SET AND LOCK BRAKES; RAISE AND LOCK BLADE
IN UP POSITION. DO NOT ATTEMPT TO RAISE BLADE BY HAND; USE THE LIFT MECHANISM ONLY.
7. LOWER BLADE TO DOWN POSITION WHEN BLADE AND ATV/UTV ARE NOT IN USE.
8. READ BLADE'S INSTRUCTION SHEETS AND ATV/UTV OWNER MANUAL.
! !

3
© 2017 Kolpin Outdoors Inc. REV 03
Kit Contents:
Item Qty P rt Description P rt Number
11Base Mount Plate -
22Mount Strap Plate -
34Spacer Plate -
44Square U-Bolts -
54Round U-Bolts -
64Carriage Bolt, Zinc Plated, M12-1.75 x 40mm LG -
74Carriage Bolt, Zinc Plated, M8-1.25 x 25mm LG -
816 Flange Locknut, Zinc Plated, M8-1.25 -
94Flange Locknut, Zinc Plated, M12-1.75 -
10 1Instruction Guide (not shown) -
1
8
3
2
4
7
6
9
6
2
5
9
8

4
© 2017 Kolpin Outdoors Inc. REV 03
BEFORE YOU BEGIN:
• Your Kolpin ccessory is exclusively designed for
your vehicle
• Ple se re d nd underst nd ll instructions
• Verify ll p rts nd tools re ccounted for
• To ensure s tisf ctory inst ll tion, follow ll steps
correctly nd in the sequence described
• Keep these instructions for future reference or for
inform tion l requests
• To f cilit te inst ll tion, m ke sure th t your vehicle
is cle n nd free of debris
• All directions referring to right nd left re when the
rider is sitting on the m chine
• The pl stic skid pl te will need to be modified to be
reinst lled on the vehicle
TOOLS REQUIRED:
• 13mm Socket
• 19mm Socket
• Drill or cutting tools for pl stic
• Depending on vehicle, ddition l tools
m y be required to remove pl stic skid
pl te
APPROXIMATE ASSEMBLY TIME: 30 minutes
Note: Remov l nd modific tion of the pl stic skid pl te is recommended.
NOTICE
The ALL MOUNT is designed to tt ch to multiple
UTV br nds. Some items cont ined in the kit re
option l nd m y not be required to complete the
inst ll tion.
Frequently check to verify the mount is centered
under the UTV, does not interfere with other
components, nd th t the pproxim te mount set-
b ck dist nce from the front bumper is m int ined
during inst ll tion.
CAUTION
Verify wires, c bles, hoses or br ke lines re not
pinched or d m ged during inst ll tion.
NOTICE
Inst ll the proper u-bolt for your fr me type:
Item #4 = Squ re Tube Fr mes
Item #5 = Round Tube Fr mes
Only four u-bolts re required. U-bolts c n be
inst lled to the UTV fr me front-to-b ck, left-to-right
or combin tion of both.
NOTICE
Approxim te B se Mount Pl te, Item #1,
Set-B ck Dist nce: 17-19 inches (43-48 cm)
Me surement Loc tion: Front edge of b se mount
pl te to bottom edge of front bumper NOTICE
Pl stic skid pl te m y need to be modified to llow
fitment of mount pl tes.
Pl stic skid pl te c n be re-inst lled if desired.
Pl stic skid pl te provides underside protection
th t mount pl tes by themselves c nnot provide.

5
© 2017 Kolpin Outdoors Inc. REV 03
Inst ll tion Prep:
1. If equipped, detach the plastic skid plate from the
vehicle to gain access to vehicle frame mounting
locations.
Mount Pl te Inst ll tion:
1. Pre-determine your u-bolt type and mounting strap
locations. Select from provided u-bolts, items #4 or
#5 and pre-fit the mount strap plates, item #2, to the
frame as shown. (See Illustrations 1-1 and 1-2).
2. Optional note: For installers who wish to modify
and re-install the UTV skid plate, refer to steps 3
and 5, before pro eeding to Step 6.
3. After finding pre-determined u-bolt mounting
locations in step 1, trim the skid plate. Mark or scribe
locations for u-bolts to fit thru skid plate.
4. Drill holes through the skid plate at locations marked.
Use a 3/8” to 1/2” bit to create an oversized hole that
will allow some relief when installing hardware.
Note, a high speed utting tool (like a Dremel)
with a utting bit will also work. (See Illustration
1-3).
5. Re-install the plastic skid plate(s) using OEM fasten-
ers. (See Illustration 1-3).
Ill. 1-1
Item #4
Item #5
Ill. 1-2
Item #2
Ill. 1-3

6
© 2017 Kolpin Outdoors Inc. REV 03
Mount Plate Installaon (connued):
6. Insert the u-bolts, items #4 and/or #5, around the
pre-determined locations.
7. If required, place spacers, item #3, onto u-bolts to fit
between mount strap plates and vehicle frame. Spac-
ers provide options to mount plates evenly to vehicle.
(See Illustration 1-4).
Note, spa ers are optional and
may not be required for ertain installations.
8. Install the mount strap plates using M8 nuts, item #8.
Verify the strap plates lay flat and do not contact any
part of the vehicle other than the mounting points. Do
not tighten fasteners at this time. (See Illustration 1-5).
9. Install the M12 carriage bolts, item #6, into the center
slots of the mount strap plates as shown. (See Illustra-
tion 1-5).
Note, installing four M12 arriage bolts is
preferred, but ertain installations may not allow
four to be used.
10. Insert M8 carriage bolts, item #7, into four locations of
base plate, item #1. Fasten base mount plate, item #1,
to strap plates using M12 lock nuts, item #9, as shown.
Do not tighten at this step. (See Illustration 1-6).
11. Verify the base mount plate set-back distance and
center within the mount strap plates. Tighten the M12
nuts to specification. (See Illustration 1-7).
Item #3
Frame tube
Ill. 1-4
Ill. 1-5
Item #6
Item #8
Ill. 1-6
Item #9
Item #7Item #1
Ill. 1-7
12MM FASTENER TORQUE:
50 ft. lbs. (67 Nm)
12. Tighten the M8 locknuts for the u-bolts. Do not over-
tighten. The excess threads can be trimmed, but leave
3-4 threads exposed past the locknut.

7
© 2017 Kolpin Outdoors Inc. REV 03
Locknut
Ill. 1-8Universal mount
plate location
Mount Pl te Inst ll tion (continued):
13. The universal mount plate, not included in kit, will
be attached to the base mount plate as shown.
The M8 carriage bolts will fasten universal plate
with M8 locknuts, item #8. Tighten to
specification. (See Illustration 1-8).
8MM FASTENER TORQUE:
17 ft. lbs. (23 Nm)
Item Qty P rt Description H rdw re Service Kit
PN 34-0013
11Base Mount Plate -
22Mount Strap Plate -
34Spacer Plate -
44Square U-Bolts Included
54Round U-Bolts Included
64Carriage Bolt, Zinc Plated, M12-1.75 x 40mm LG Included
74Carriage Bolt, Zinc Plated, M8-1.25 x 25mm LG Included
816 Flange Locknut, Zinc Plated, M8-1.25 Included
94Flange Locknut, Zinc Plated, M12-1.75 Included
10 1Instruction Guide (not shown) -
Service Kit

8
© 2017 Kolpin Outdoors Inc. REV 03
One Ye r Limited W rr nty
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser,
free of charge, any part or parts found upon examination by Kolpin to be defective in material,
workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be
borne by the purchaser. If Kolpin determines that the product must be returned to the factory for
credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and
shipping instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse,
improper maintenance, normal wear, or other causes beyond the manufacturer’s control. In order to
protect you and your ATV, certain parts of the plow system and/or hardware are designed to fail
when the equipment is over-stressed. Parts that are lost due to loosening and improper
maintenance are not covered under warranty. This warranty does not cover removal or reinstallation
labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original
manufacturer’s warranty. Most hardware is general in nature and is easily obtained locally. Be sure
to replace with minimum metric class 8.8 specification.
Kolpin Outdoors, Inc.
Telephone: [phone]
Toll Free: (877)-956-5746
F x Number: (800)-245-7569
www.kolpin.com
Em il: [e-mail]