Komet AmbiKab User manual






 

AmbiKabOwner’s Manual










.
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification.

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry a cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
7. Do not install near any heat sources, such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
8. Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
9. Only use attachments/accessories specified by the manufacturer.
10. Unplug this apparatus during lightning storms or when not used for long periods of time.
11. Refer all servicing to qualified personnel. Servicing is required when the apparatus has
been damaged in any way, such as a power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally or has been dropped.
12. CAUTION:To disconnect the unit completely from the Mains, unplug the unit. Turning
the power switch off does not completely disconnect the unit from the Mains.
13. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades, with one wider than the other. A grounding-type plug has two blades and a
third grounding prong. The wide blade and the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
14. The unit shall not be exposed to dripping or splashing of liquids, and that no objects filled
with liquids such as vases shall be placed on the unit.
15. WARNING:This is a Class 1 apparatus. This unit should be connected to a MAINS socket
outlet with a protective earthing connection.
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification.

EU ENVIORNMENTAL DIRECTIVES
RoHS This product is compliant with the EU Directive 2011/65/EU for the Restriction of
the use of Certain Hazardous Substances in Electrical and Electronic Equipment. No lead
(Pb), cadmium (Cd), mercury (Hg), hexavalent chromium (Cr+6), PBB or PBDE is
intentionally added to this device. Any traces of impurities of these substances contained
in the parts are below the RoHS specified threshold levels.
REACh This product is compliant with the European Union Directive EC1907/206 for
the Registration, Evaluation, Authorization, and Restriction of chemicals (REACh) and
contains none or less than 0.1% of the chemicals listed as hazardous chemicals in the
REACh regulation.
WEEE This symbol on the product or its packaging indicates that this product must
not be disposed of with other waste. Instead, it is your responsibility to dispose of your
waste equipment by handing it over to a designated collection point for the recycling
of waste electrical and electronic equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help conserve natural resources and
ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste equipment for
recycling, please contact your local city recycling office or the dealer from whom you
purchased the product.
CE This product complies with the European Union Council Directives and Standards
relating to electromagnetic compatibility EMC Directive (2006/95/EC) and the Low
Voltage Directive (2004/10)
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification.

Thank you for purchasing the Komet AmbiKab
Komet Amplification is proud to announce our new, proprietary effects processing AmbiKab
speaker system. This new innovation provides a unique solution to the age old problem of
applying ambient, time-based effects to an amplifier’s sound without degrading the original
sound in any way. Most guitar players are familiar with the issue: when applied time based
effects such as reverb or delay applied before distortion, the sound “washes out” and becomes
indistinct. The proper way to apply these types of effects is after the distortion –much as you
would in the mix down stage in a recording studio.
Some amplifiers employ an on board effects loop for this, but that only works as long as the
amplifier’s output stage itself does not contribute to the distortion. Most classic vintage
amplifiers and many non master volume designs such as our Komet amplifier lineup do employ
output stage distortion as part of the sonic recipe. It is part of what makes these amplifiers so
extraordinarily responsive and rich sounding. Effects loops do not work well in those amplifiers.
This is where the AmbiKabcomes into play. It allows the amplifier to directly drive a set of
guitar speakers “dry signal” without any effects added directly to it. A portion of this dry signal
is then split off by the AmbiKab’sinternal circuitry and sent out into an effects unit. From
there, a 100% effects signal “wet signal” is fed back into the AmbiKabwhere a separate,
internal stereo power amplifier sends the signal to a dedicated set of speakers.
The AmbiKabfeatures a send level control to accommodate a variety of effects from floor
pedals to studio quality rack units. On the return side, a volume control for the internal stereo
amp governs the proportion of effects signal that is being added to the guitar sound.
The AmbiKabcan be used with mono effects (both stereo channels bridged) or in full stereo
mode. The sonic results of this new cabinet system are astonishing! The amplifier reacts to the
player’s input as if there were no effects employed at all (as the amplifier never actually “sees”
the effects). Additionally, the ratio between wet and dry signals always stays constant, in other
words - as the guitar player “rolls down “ the volume to clean up the amplifiers sound, or varies
their picking dynamics, the effects signal changes proportionally to the amplifiers output signal.
Players who have used traditional amplifiers with built in reverb, will be familiar with this
problem. If you set your reverb level for your lead sound, the reverb disappears when you roll
down your volume for rhythm, and vice versa. The AmbiKabsolves this age old problem.
The AmbiKabgives you a true, studio quality effects sound anywhere, without the hassle of a
traditional wet/dry/wet rig requiring additional speaker cabinets, amplifiers, mixers and cables.
You just need your favorite amplifier head, effects unit/pedal board and the AmbiKab.
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification.

CONTROL PANEL LAYOUT (left to right):
1. AC Input: this IEC receptacle accepts standard DIN AC power cable. All Komet
amplifiers can be modified to run on either 120V or 240V. Please inquire with Komet
Amplification for the AC power voltage conversion information.
2. Power Switch: engages the wall AC / power to the amplifier.
3. Pilot Light:illuminates when power switch is placed in the "On" position.
4. Effects Volume:determines the volume of the effect(s).
5. Effects Bass:reduces the bass content of the wet signal only.
6. Effects Input:(left mono) mono or stereo input from effect pedal / board.
7. Effects Input:(right) input from effect pedal / board.
8. Effects Kill:allows owner to use a footswitch to disengage the effects signal.
9. Effects Send:(line out) send to effects unit input.
10. Effects Send:(level) determines the amount of signal sent to the effect's units.
11. Speaker Input:(16 Ohms) cabinet input from amplifier’s speaker out.
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification.

WHAT THE KOMET AMBIKABIS:
The Komet AmbiKabis a self contained, powered stereo Wet/Dry/Wet system that allows the
user to employ ambient, time-based effects such as reverb and delay (“wet signal”) to the guitar
sound independently from the straight guitar amplifier tone (“dry signal”).
WHAT THE KOMET AMBIKABDOES:
When you plug your guitar amplifier into the AmbiKab'sSpeaker Input, the amplifier is
connected directly to the internal 12” guitar speakers.
From there, a small portion of the signal is sent back out of the system via the adjustable Line
Level jack. This signal is sent to the effects, and then returned to the AmbiKab'sEffects In,
either in mono or in stereo. The AmbiKab’sinternal dual channel Class D power amp amplifies
the effects and powers its own pair of 10” speakers.
As a result, the amp never “sees” the effects and thus sounds and reacts exactly as if there were
no effects used at all. The all important: guitar-amp-guitar signal chain - remains pure and
unaffected.
CONNECTING TO THE KOMET AMBIKAB:
The Komet AmbiKabcan be used with any guitar amplifier that has a speaker output jack.
1. Connect the AmbiKab'sAC input using the grounded IEC power cable to a wall socket and
engage the Power switch on.
2. Connect your amplifier's output to the AmbiKab'sSpeaker Input jack using a quality
SPEAKER CABLE with 1/4” connectors
3. Connect the AmbiKab'sEffects Send jack to your effects unit's Input jack using a shielded
GUITAR CABLE.
4. Connect your effects unit's stereo outputs (Left/Right) to the AmbiKab'stwo Effects input
jacks using another pair of shielded GUITAR CABLES
If you are using mono effects, use a single shielded GUITAR CABLE from your effects unit's
output to the AmbiKab’sLeft/Mono input. This will automatically bridge the AmbiKab's
stereo channels and send the mono signal to both effects speaker.
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification

SETTING THE CONTROLS ON THE KOMET AMBIKAB:
1. The Effects Send Level control determines the amount of signal sent to the effect's units.
Set this control to allow for sufficient signal levels to drive the effects unit without
clipping. Some effects will have a clipping indicator, on others you will have to use your
ears. If the effects signal is distorting, back off the Effects Send Level. Remember that
the AmbiKabsends a portion of the speaker signal to your effects unit. The higher your
playing volume, the more signal is being sent. This means that quieter playing situation
and lower wattage guitar amplifiers will call for higher settings of the Effects Send Level,
and vice versa.
2. The Effects Volume control determines the volume of the effect(s) that is coming out of
the AmbiKab'seffects speakers. In essence, this is your effects level control
3. The Effects Bass Cut control can be used to reduce the bass content of the wet signal
only. It does not affect the dry guitar signal.
EXTREME SETTINGS:
The AmbiKabis designed to work with a very wide variety of amplifiers and effects. There can
occasionally be situations where extreme settings, such as Effects Send Level and Effects
Volume controls turned up all the way in combination with effects units capable of sending
extreme levels of signal, can create an internal feedback condition. This may manifest itself as
a sustained howling or bass oscillation noise. If you encounter this, engage the Bass Cut
control and/or reduce Effects Volume until the oscillation noise stops.
TROUBLESHOOTING:
Pilot Light Not On:
Check to see if the amplifier’s AC cable is plugged in at wall and plugged in at the IEC
connection on the back panel of the amp
No Sound:
Check the speaker connection at back of amp and at the input of the speaker cabinet.
(continued)
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification.

Check the guitar cables and signal patch cables.
Bypass all effects from pedal board and connect only one pedal from pedal board and test
AmbiKab. If the AmbiKabfunctions with just one pedal, then it is operational. Thoroughly
check your pedal board connections and set your pedal board up through the AmbiKabagain.
Removing Back Panel:
Please be very careful when removing the back panel for any inspection. The speaker harness
wiring will only allow you to open the panel a few inches. You will have to un-plug four
harness connections so as to remove the back panel so you can easily have access your speakers.
We recommend that you (very carefully) unscrew the input nut (on the speaker input) with a 1/2”
nut driver. This will release the Switchcraft ¼” jack from the panel. You will also have to
manually remove the red and black terminal wires (which are also attached to the input jack)
from the power board. Then un-plug the two remaining 10” speaker wiring harnesses from the
pre amp board. Make sure you re-install them all correctly when done. If not, your cabinet will
be out of phase. ALWAYS make sure the IEC power cable is not plugged into the AC input
when opening the back panel.
SPECIFICATIONS
• Dimensions: 30" x 11.50 x 26.50
• Weight:75 lbs.
•Speakers: two -12” Celestion speakers and two 10” Celestion speakers.
• Power:80 Watts RMS (standard setup) 100 Watts plus depending on speaker selection.
CONTACT
KometAmplification
1865 Dallas Drive
Baton Rouge, LA 70806-1454
[phone]
Email: [email protected]
Website: www.kometamps.com
Facebook: https://www.facebook.com/pages/Komet-Amplification/739410886107995
Tumbler: http://kometamplification.tumblr.com/
Twitter: https://twitter.com/kometamps
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification

KOMETAMPLIFICATION’S WARRANTY
This warranty shall be void and of no force of effect in the event a covered product has been
modified in design or function, or subjected to abuse, misuse, (which includes improper
removal of the AmbiKab’spack panel causing damage to wiring harnesses, power
amplifier or preamp board, speaker harnesses and speakers), mishandling or unauthorized
repair. Further, product malfunction or deterioration due to normal wear is not covered by this
warranty. KometAmplification warrants their amplifiers to be free from defects in materials
and workmanship for a (2) two year period. KometAmplification will repair or replace any part
there of which, upon inspection by KometAmplification, is found to be defective in materials or
workmanship. As a condition to the obligation of KometAmplification to repair or replace such
a part, the product must be returned to KometAmplification with a copy of the original and
dated sales receipt from the authorized Kometdealer. KometAmplification’s warranty is only
applicable to the original owner of the amplifier. Warranty is not transferable.
The Proper Return Authorization must be obtained from KometAmplification in advance of a
return. Please call or e-mail KometAmplification to receive authorization for warranty repair.
All returns must be accompanied by a written statement setting forth the name, address, and
daytime telephone number of the owner, together with a brief description of any claimed defects.
Parts or product for which replacement is made shall become the property of
KometAmplification. The customer may be responsible for all costs of transportation and
insurance, both to and from KometAmplification, depending on result of inspection and
validation of warranty request. Customer may be required to prepay such costs.
KometAmplification shall use reasonable efforts to repair or replace any part covered by this
limited warranty within thirty days of receipt. In the event repair or replacement shall require
more than thirty days, KometAmplification shall notify the customer accordingly.
Warranty Exclusions and Limitations: Notwithstanding the foregoing, all warranty claims are
excluded if:
i. the Product(s) is damaged or destroyed due to the effects of force majeure, including but
not limited to: Acts of God, flood, fire; Acts of War, government authority, acts of
terrorism, riots, explosions, embargo; Labor difficulty, strikes, breakdown of machinery
or equipment, accidents; Shortage or inability to obtain raw materials, equipment, fuel,
power, transportation; or Any cause beyond KOMET's reasonable control or due to
environmental influences such as wind, hailstones, snow, frost, etc.
(continued)
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification

ii. the Product(s) is damaged from abuse, misuse, improper installation, or neglect;
iii. the Product(s) is altered or appears to have been attempted repair by unauthorized
personnel;
iv. if the Product(s) has been modified in any way; or if a defective product has remained in
use, resulting in consequential damage to the Product(s).
SHIPPING INSTRUCTIONS
Note: KometAmplification highly recommends that you review all packaging, insurance
requirements, and shipping recommendations of the shipping company you intend to use.
Kometsuggests using a foam injected, 300lb. test, corrugated cardboard shipping box.
Kometalso suggests having your amplifier professionally packaged to ensure safety.
Any amplifier or speaker cabinet being shipped should be insured for at least its full value.
Please do not return ship your amplifier or AmbiKabwith the AC power cable.
We are a commercial address. Please check any corresponding box on shipping label.
Please do not return ship using “Home Delivery“ service or Saturday delivery.
Please do not send for early morning (before 9:00 A.M.) delivery. We prefer afternoon delivery.
Note: KometAmplification will not be held responsible for any Kometamplifier, amplifier
component, or contents, damaged or lost during shipping to KometAmplification. Komet
Amplification will not be held responsible for any damage or loss of an amplifier due to
improper packaging or labeling by the customer or packager. Any and all damaged packages and
their contents in which claims are filed for damage via shipping to KometAmplification are
between customer and shipper. KometAmplification will do their absolute best to help any
customer with a shipping insurance claim.
Our address:
Komet Amplification, L.L.C.
1865 Dallas Drive
Baton Rouge, La. 70806-1454
[phone]
E-mail: [email protected]
Copyright 1999-2017, KometAmplification. Group, L.L.C. May not be reproduced in any form without express written consent from KometAmplification