Konix DRAKKAR LOKI D27VA240A User manual

USER MANUAL
LOKI
Borderless wide screen
240
Hz
7
1MS
ULTRA FAST
240
Hz
7
1MS
ULTRA FAST
240
Hz
7
1MS
ULTRA FAST

Read all instructions before using the appliance and retain for reference.
1. Unplug the monitor before cleaning it with a slightly damp, clean cloth.
2. Wipingthescreenonceithasbeenturnedoffwithadrymicrobrecloth
is recommended.
3. Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
4. This monitor is designed with ventilation holes on the back of the casing.
Do not cover or block them.
5. Avoidplacingthemonitornearheaters,stoves,replacesorothersources
of heat, as well as in rooms lacking adequate ventilation.
6. Do not insert any objects or spray any liquids into the vents.
7. Do not position the monitor in unsafe locations. If the monitor falls, it may
be damaged and may injure nearby people.
8. Unplug the monitor if it is not going to be used for an extended period.
9. Do not place heavy objects on the monitor, its power cord or any
connected cables.
10. Do not open the back panel of the monitor, as it contains a high-voltage
current even when not plugged in.

3
A
CONTENTS
• Contents.....................................................................................03
• Components ............................................................................ 04
• Overview ................................................................................. 05
• Stand Assembly...................................................................... 06
• Wall Mounting..........................................................................08
• Connectivity............................................................................. 09
• Basic Operation.........................................................................11
• lndicator Light............................................................................11
• Operation.................................................................................... 12
• ECO Modes and Gameplus Switching .............................15
• Specications ............................................................................16
Read all instructions before using the appliance and retain for reference.
1. Unplug the monitor before cleaning it with a slightly damp, clean cloth.
2. Wipingthescreenonceithasbeenturnedoffwithadrymicrobrecloth
is recommended.
3. Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
4. This monitor is designed with ventilation holes on the back of the casing.
Do not cover or block them.
5. Avoidplacingthemonitornearheaters,stoves,replacesorothersources
of heat, as well as in rooms lacking adequate ventilation.
6. Do not insert any objects or spray any liquids into the vents.
7. Do not position the monitor in unsafe locations. If the monitor falls, it may
be damaged and may injure nearby people.
8. Unplug the monitor if it is not going to be used for an extended period.
9. Do not place heavy objects on the monitor, its power cord or any
connected cables.
10. Do not open the back panel of the monitor, as it contains a high-voltage
current even when not plugged in.
SAFETY AND WARNINGS

4
User Gu ide
” FreeSync Monitor
(D27VA240A)
A
B C D
H
G
E
IF
A
AMonitor
BStand Stem
CStand Base
DCM4*26mm Screws x 5
EKM4*12mm Screws x 3
FVESA connectors x 4
GPower Cable and Adapter
HDP Cable
IUser Guide
COMPONENTS
OVERVIEW
Monitor Controls
Monitor Ports
(Note : Each kind of screws include extra one for spare).

5
FVESA connectors x 4
GPower Cable and Adapter
HDP Cable
IUser Guide
OVERVIEW
Monitor Controls
Menu Button: Press to display the OSD menu or enter sub-menus.
Up Button: Press to move up in the menus.
Down Button: Press to move down in the menus.
Exit Button: Press to exit.
Power Button: Press to turn the monitor on/off.
A
Monitor Ports
HDMI Connector: lnsert one end of the HDMI cable into the computer’s HDMI
output and connect the other end to the monitor’s HDMI port.
DisplayPort Connector: Insert one end of the DisplayPort cable into the
computer’s DisplayPort output and connect the other end to the monitor’s
DisplayPort port.
Audio Output: lnsert one end of the Audio cable into the computer’s Audio
output to receive the Audio signals from your monitor.
Power Connector: Insert the power cable to supply power to the monitor.
(Note : Each kind of screws include extra one for spare).
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
1
3
4
5
2
6 987
1
3
4
5
2
6 987

6
A
Keep the foam underneath the monitor before attaching the stand.
STAND ASSEMBLY
1. Open the packaging, gently take out the foam and monitor.
2. Remove the upper foam, keep the monitor laying on nether foam.
3. Take out stem and base, Lock them with 2pcs KM4*12mm screws.
(Screws are in the accessory bag, 1pcs buffer)

7
A
4. Insert the stem to the slot of back cover, them lock them
with 4pcs CM4*26mm screws.( Screws are in the accessory
bag, 1pcs buffer )
5. Gently have the monitor stand up and enjoy using it.

8
A
WALL MOUNTING
CONNECTIVITY
Power Cable
Connect the included power cable to the power connector, and then plug
the other end into an wall outlet.
Earphones
Plug in your earphones to receive audio signals from your monitor. If your
earphones are connected to the monitor and audio devices are connected to
your computer at the same time, the audio devices will not produce sound.
Earphones and other audio devices not included.
Mount
(Not included)
1. Open the packaging, gently take out the foam and monitor.
2. Remove the upper foam, keep the monitor laying on nether foam.
3. Take out 4pcs VESA Connector(30mm height, in the accessory bag),
and lock them in back cover with straight screwdriver.
4. Follow the directions with your mount, and install the monitor on the
wall or bracket as you like.

9
A
CONNECTIVITY
Power Cable
Connect the included power cable to the power connector, and then plug
the other end into an wall outlet.
Earphones
Plug in your earphones to receive audio signals from your monitor. If your
earphones are connected to the monitor and audio devices are connected to
your computer at the same time, the audio devices will not produce sound.
Earphones and other audio devices not included.
Power Cable
Earphones
(Not included)

10
A
DP
In order for the monitor to receive DP signals from the computer, use the DP
cable to connect the monitor to the computer.
DP OUTPUT
PC
HDMI OUTPUT
PC
BASIC OPERATION
Solid blue light indicates power is on and the monitor is operating normally.
Flashing blue light indicates no video source, no horizontal or vertical signal
has been detected. Please ensure your computer is on and all video cables
are fully inserted and/or connected.
1. Connect the other end of the cable to the corresponding connector
on your monitor.
2. Connect the power cable to your monitor then connect the other end to
your power source. lt is recommended that you use a surge protector with
adequate voltage if a wall cannot be reached directly.
3. Locate the power button on the monitor and press it to turn the monitor on.
FreeSync
The feature itself is off by default when setting 75Hz refresh rate. In order to
use this feature, please note you must have hardware with FreeSync capa-
bility, an HDMI cable or DP cable, and the latest graphic drivers. To use this
feature, connect your computer and monitor with an HDMI cable or DP cable.
A􀁑er connecting, you may receive a prompt to enable the feature on your
computer. If you do not receive the prompt, you may need to enable the
function in your graphics card menu. See your graphics card manufacturer’s
documentation for instructions on how to turn on and/or enable FreeSync.
INDICATOR LIGHT
DP Cable
(Included)
HDMI Cable
(Not Included)
HDMI
In order for the monitor to receive HDMI signals from the computer, use a
HDMI cable to connect the monitor to the computer.

11
A
BASIC OPERATION
Solid blue light indicates power is on and the monitor is operating normally.
Flashing blue light indicates no video source, no horizontal or vertical signal
has been detected. Please ensure your computer is on and all video cables
are fully inserted and/or connected.
lnsert one end of the DP cable into your PC’s graphics card. An HDMI
cable may also be used. A HDMI cables is not included.
HDMI Connector
HDMI 1.4 HDMI 2.0
DP Connector
1. Connect the other end of the cable to the corresponding connector
on your monitor.
2. Connect the power cable to your monitor then connect the other end to
your power source. lt is recommended that you use a surge protector with
adequate voltage if a wall cannot be reached directly.
3. Locate the power button on the monitor and press it to turn the monitor on.
FreeSync
The feature itself is off by default when setting 75Hz refresh rate. In order to
use this feature, please note you must have hardware with FreeSync capa-
bility, an HDMI cable or DP cable, and the latest graphic drivers. To use this
feature, connect your computer and monitor with an HDMI cable or DP cable.
A􀁑er connecting, you may receive a prompt to enable the feature on your
computer. If you do not receive the prompt, you may need to enable the
function in your graphics card menu. See your graphics card manufacturer’s
documentation for instructions on how to turn on and/or enable FreeSync.
INDICATOR LIGHT
lndicator Light

12
A
The On-Screen Display (OSD) Menu may be used to adjust your monitor’s
settings and appears on screen alter turning on the monitor and pressing the
Mbutton.
OPERATION
Whenusingthemonitorforthersttime,settingswillautomatically
adjusttooptimalsettingsaccordingtoyourcomputer’sconguration
and parts etc.
1. Press any one of the buttons ( M, , , E, )
to activate the navigation window.
2. Press Mto enter the OSD menu.
3. Press or to browse functions.
• Highlight the desired function, then press Mto enter the sub-menu.
• Press or to browse sub-menus, then press Mto highlight the desired
function.
• Press or to highlight an option, then press Mtoconrmthesettings
and exit the current screen.
4. Press Eto exit the current screen.
LIST OF FUNCTIONS
eco
DP
Resolution：1920x1080@60Hz
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
DP
HDMI1(2.0)
HDMI2(1.4)
HDMI3(1.4)
Window1：
InputSource：DP
Resolution：1920x1080@60Hz
Window2:
InputSource：
Resolution：
eco
DP
Resolution：1920x1080@60Hz
Input Source
Brightness/Contrast
Color Setting
Picture QualitySetting
Display
Audio
Multi-Window
OSD
Other
DP
HDMI1(2.0)
HDMI2(1.4)
HDMI3(1.4)
Window1：
InputSource：DP
Resolution：1920x1080@60Hz
Window2:
InputSource：
Resolution：
Input
Source
NO NE Auto switch to H DMI or DP signa l
H DM 0NO N E S witc h to H D MI s igna l input
H DM 4
DP
B rightness
C ontras t
B rightness 010 0 Ad ust display brightness
B lac level 0 10 0 Ad ust bla c level
C ontras t 0 10 0 Ad ust display c ontra st
DC R On Turn on DC R f unction
O  Turn o DC R f unction
C olor
S etting
G amma
G amma 1.8,
G amma 2 .0,
G amma 2.2,
G amma 2 .4,
G amma 2 .6
S et G a mma a dd in
Pic ture M ode St an da rd, Ph oto,
Movie, G ame, FP S,
R TS
Set visual mode a cc ording to ac tivity
C olor
Temperat ure rm, C oo ser S elect c olor temp erat ure
Low B lue L ight 0 10 0 Set blue light filtering level
H ue Ad ust hue levels
S atu rat ion Ad ust sa turation levels
Picture
uality
Setting
Sharpness 0 10 0 Ad ust display sha rpness
R esponse T ime O , H igh, M iddle,
Low Ad ust response time
Noise R eduction O , H igh, M iddle,
Low
R educe the interference of image noise
caused by signal source interference
Dyna mic
Luminous
C ontrol
O n, O 
C ompensate for gray s cale display
screen a nd st rengthen the e pression of
gray sca le
MPR T O n, O  Turn M PR T on/o
Display Aspect R at io ide S creen, 4: ,
Auto
Select on sc reen as pect ratio
LED M ode Normal, F lic er, O  S elect led display mode
Audio
Mute O n, O  Turn mute m ode on/o
Volume 0 10 0 Ad ust au dio volume
Audio S ource
Auto S ource, D P,
H DM I 1,H DM I 2
H DM I
Select a udio signa l input via H DMI or D P
H DM 4
0 10 0
010 0

13
A
LIST OF FUNCTIONS
Input
Source
NO NE Auto switch to H DMI or DP signa l
H DM 0NO N E S witc h to H D MI s igna l input
H DM 4
DP
B rightness
C ontras t
B rightness 010 0 Ad ust display brightness
B lac level 0 10 0 Ad ust bla c level
C ontras t 0 10 0 Ad ust display c ontra st
DC R On Turn on DC R f unction
O  Turn o DC R f unction
C olor
S etting
G amma
G amma 1.8,
G amma 2 .0,
G amma 2.2,
G amma 2 .4,
G amma 2 .6
S et G a mma a dd in
Pic ture M ode St an da rd, Ph oto,
Movie, G ame, FP S,
R TS
Set visual mode a cc ording to ac tivity
C olor
Temperat ure rm, C oo ser S elect c olor temp erat ure
Low B lue L ight 0 10 0 Set blue light filtering level
H ue Ad ust hue levels
S atu rat ion Ad ust sa turation levels
Picture
uality
Setting
Sharpness 0 10 0 Ad ust display sha rpness
R esponse T ime O , H igh, M iddle,
Low Ad ust response time
Noise R eduction O , H igh, M iddle,
Low
R educe the interference of image noise
caused by signal source interference
Dyna mic
Luminous
C ontrol
O n, O 
C ompensate for gray s cale display
screen a nd st rengthen the e pression of
gray sca le
MPR T O n, O  Turn M PR T on/o
Display Aspect R at io ide S creen, 4: ,
Auto
Select on sc reen as pect ratio
LED M ode Normal, F lic er, O  S elect led display mode
Audio
Mute O n, O  Turn mute m ode on/o
Volume 0 10 0 Ad ust au dio volume
Audio S ource
Auto S ource, D P,
H DM I 1,H DM I 2
H DM I
Select a udio signa l input via H DMI or D P
H DM 4
0 10 0
010 0

14
A
ECO MODES AND GAMEPLUS SWITCHING
Multi-
indow
Multi- indow OIP M od B P
in
Select PI P PB P modes a ccording to the
number of input signa ls etc.
Sub in nput DP DM ( . )
DM ( . )
DM ( . )
Select a ccording to input signal for PIP
PB P mode
PIP e Small edium
arge
the PIP display windo e
PIP Position the PIP window position
S wap OS wa p the PI P/PB P signal sources
O S D
angua ge
Fran 한국
S et O S D la ngua ge
O S D -Position - just the O S D’s hori nta l position
O S D Position - just the O S D’s ertical position
O S D
Transpar ency
-just O S D s o erall tra nspa rency
O S D T ime O ut - Set h ow long the O S D remains open
aer non-use
O S D R otat ion orma hen the user ips the display this
function c a n a ls ip the O SD to a chie e
the best d isplay a ngle
O ther
DP ersion DP . D P . Display D P ersion
FreeSy nc
apti e Sy nc)
O n Turn the FreeSy nc func tion on o
DR On Turn th DR f unction on o
R eset R eset monitor c onfigurat ions
Top R ight Top
e ottom R ight
Botto e

15
2. Press to switch Gameplus modes. According to the needs of your
game, choose the corresponding game icon. These game icons are
primarily designed to optimize your aim during FPS games, though
they can be used for other scenarios.
2. Press E to set RGB range (Limited or Full) effects.
A
ECO MODES AND GAMEPLUS SWITCHING
1. Press any one of the buttons ( M, , , E, )
to activate the navigation window.
2. Press to switch ECO modes. These modes (Standard, Photo,
Movie, Game, FPS and RTS) can be used to optimize settings
according to your activity. Standard mode is suitable for most activities.
Multi-
indow
Multi- indow OIP M od B P
in
Select PI P PB P modes a ccording to the
number of input signa ls etc.
Sub in nput DP DM ( . )
DM ( . )
DM ( . )
Select a ccording to input signal for PIP
PB P mode
PIP e Small edium
arge
the PIP display windo e
PIP Position the PIP window position
S wap OS wa p the PI P/PB P signal sources
O S D
angua ge
Fran 한국
S et O S D la ngua ge
O S D -Position - just the O S D’s hori nta l position
O S D Position - just the O S D’s ertical position
O S D
Transpar ency
-just O S D s o erall tra nspa rency
O S D T ime O ut - Set h ow long the O S D remains open
aer non-use
O S D R otat ion orma hen the user ips the display this
function c a n a ls ip the O SD to a chie e
the best d isplay a ngle
O ther
DP ersion DP . D P . Display D P ersion
FreeSy nc
apti e Sy nc)
O n Turn the FreeSy nc func tion on o
DR On Turn th DR f unction on o
R eset R eset monitor c onfigurat ions
Top R ight Top
e ottom R ight
Botto e
eco
Standar d
RGB R ange:Limited
eco
eco
Standar d
RGB R ange:Limited
eco
eco
Standar d
RGB R ange:Limited
eco
eco
Standar d
RGB R ange:Limited
eco
eco
Standar d
RGB R ange:Limited
eco
eco
Standar d
RGB R ange:Limited
eco
eco
Standar d
RGB R ange:Limited
eco

Lisez toutes les instructions avant d’utiliser l’appareil et conservez-les pour référence.
1. Débranchez le moniteur avant de le nettoyer avec un chiffon propre légèrement humide.
2 Ilestrecommandéd’essuyerl’écranunefoiséteint,avecunchiffonenmicrobresec.
3 N’utilisez pas d’alcool ménager, de liquides à base d’ammoniac ou d’autres nettoyants
agressifs.
4. Cemoniteurestdotésd’oricesdeventilationàl’arrièreduboîtier.Nelescouvrezpaset
ne bloquez pas le passage de l’air.
5. Évitez de placer le moniteur à proximité d’un radiateur, d’une cuisinière, d’un feu de
cheminée ou d’une autre source de chaleur, ou dans une pièce ne disposant pas d’une
ventilation adéquate.
6. N’insérezaucunobjetetnevaporisezaucunliquidedanslesoricesdeventilation.
7. N’installez pas le moniteur à un emplacement non sécurisé. Si le moniteur tombe, il peut
être endommagé et blesser les personnes à proximité.
8. Si le moniteur n’est pas utilisé pendant une période prolongée, débranchez-le.
9. Ne placez pas d’objets lourds sur le moniteur, sur son câble d’alimentation ou sur les
câbles qui y sont connectés.
10. N’ouvrez pas le panneau arrière du moniteur : même lorsque le moniteur n’est pas
branché, il est exposé à un courant haute tension.
SPECIFICATIONS
A
A240 A
VA
ELED
20 0 H over c loc 240 H
61 14.4 2 2.2m m
61 6 . 41m m
4 g
Ada pter
DP 1,HDMI 2. 1, HDMI1.4
DC 12V 4. 0A
1m M P R T
8 8
000:1
8 . 6 g
Net W eight
Gr oss W eight
DP Cable
16 . M
E S
E S
E S
E S
E S
E S
E S
Model
Scr een Siz e
Aspect R atio
Backligh t
Brigh tness
Panel
R esolution
R efresh R at e
R esponse Time
Viewing Angle
Con trast R atio
VES A Moun ting
Signal Inp t
Power
AMD F reeS ync
Colour s
Audio
Speak ers
Audio Out
Accessories
Additional F unctions
Flick er Free
Dimensions ( w / S tand )
Dimensions (w / o Stand )
Physical Dimensions
Low Blue Ligh t

17
Z
SOMMAIRE
• Sommaire.................................................................................... 17
• Pièces ...........................................................................................18
• Vue d’ensemble ...................................................................... 19
• Montage du support..............................................................20
• Montage mural......................................................................... 22
• Connectivité..............................................................................23
• Fonctionnement de base..................................................... 25
• Voyant lumineux .....................................................................25
• Fonctionnement......................................................................26
• Liste des Fonctions................................................................ 27
• Commutation Modes ECO et Gameplus........................29
• Caractéristiques ......................................................................30
Lisez toutes les instructions avant d’utiliser l’appareil et conservez-les pour référence.
1. Débranchez le moniteur avant de le nettoyer avec un chiffon propre légèrement humide.
2 Ilestrecommandéd’essuyerl’écranunefoiséteint,avecunchiffonenmicrobresec.
3 N’utilisez pas d’alcool ménager, de liquides à base d’ammoniac ou d’autres nettoyants
agressifs.
4. Cemoniteurestdotésd’oricesdeventilationàl’arrièreduboîtier.Nelescouvrezpaset
ne bloquez pas le passage de l’air.
5. Évitez de placer le moniteur à proximité d’un radiateur, d’une cuisinière, d’un feu de
cheminée ou d’une autre source de chaleur, ou dans une pièce ne disposant pas d’une
ventilation adéquate.
6. N’insérezaucunobjetetnevaporisezaucunliquidedanslesoricesdeventilation.
7. N’installez pas le moniteur à un emplacement non sécurisé. Si le moniteur tombe, il peut
être endommagé et blesser les personnes à proximité.
8. Si le moniteur n’est pas utilisé pendant une période prolongée, débranchez-le.
9. Ne placez pas d’objets lourds sur le moniteur, sur son câble d’alimentation ou sur les
câbles qui y sont connectés.
10. N’ouvrez pas le panneau arrière du moniteur : même lorsque le moniteur n’est pas
branché, il est exposé à un courant haute tension.
SÉCURITÉ ET AVERTISSEMENTS

18
User Gu ide
” FreeSync Monitor
(D27VA240A)
A
B C D
H
G
E
IF
Z
AMoniteur
BTige de support
CBase de support
DVis CM4*26mm (x5)
EVis KM4*12mm (x3)
FConnecteurs VESA (x4)
GCâble d’alimentation et adaptateur
HCâble DP
IGuide de l’utilisateur
PIÈCES
VUE D’ENSEMBLE
Commandes du moniteur
Ports du moniteur
(Remarque : pour chaque type de vis, une pièce supplémentaire est fournie pour
servir de pièce de rechange.)

19
Z
FConnecteurs VESA (x4)
GCâble d’alimentation et adaptateur
HCâble DP
IGuide de l’utilisateur
VUE D’ENSEMBLE
Commandes du moniteur
Bouton Menu :appuyezsurleboutonpourafcherlemenuOSDouaccéderauxsous-menus.
Bouton haut : appuyez sur le bouton pour déplacer le curseur vers le bas dans les menus.
Bouton bas : appuyez sur le bouton pour déplacer le curseur vers le haut dans les menus.
Bouton de sortie : appuyez sur le bouton pour sortir.
Bouton d’alimentation : appuyez sur le bouton pour allumer/éteindre le moniteur.
Ports du moniteur
Connecteur HDMI : Branchez le câble HDMI à la sortie HDMI de l’ordinateur et connectez l’autre
extrémité au port HDMI du moniteur.
Connecteur DisplayPort : Insérez une extrémité du câble DisplayPort dans la sortie DisplayPort
de l’ordinateur et connectez l’autre extrémité au port DisplayPort du moniteur.
Sortie audio : insérez un câble audio dans la sortie audio de l’ordinateur pour transmettre
les signaux audios de votre moniteur.
Connecteur d’alimentation : insérez le câble d’alimentation pour brancher le moniteur.
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
9
1
3
4
5
2
1 M
2
3
4 E
5
6
9
8
7
8
7
6
1
3
4
5
2
6 987
1
3
4
5
2
6 987
(Remarque : pour chaque type de vis, une pièce supplémentaire est fournie pour
servir de pièce de rechange.)

20
Maintenezlamousseenplacesouslemoniteuravantdexerlesupport.
MONTAGE DU SUPPORT
1. Ouvrez l’emballage, retirez doucement la mousse et sortez le moniteur.
2. Retirez la mousse du haut, laissez le moniteur posé sur la mousse du bas.
3. Retirez la tige et la base, verrouillez-les avec 2 vis KM4 * 12 mm.
(Les vis sont dans le sachet d’accessoires, tampon 1 pièce)
Z