Konix DRAKKAR OLRUN User manual

USER MANUAL
OLRUN
Borderless wide screen

Read all instructions before using the appliance and retain for reference.
1. Unplug the monitor before cleaning it with a slightly damp, clean cloth.
2. Wipingthescreenonceithasbeenturnedoffwithadrymicrobrecloth
is recommended.
3. The monitor is designed with ventilation holes in the back of the case.
Do not cover or block them
4. This monitor is designed with ventilation ho les on the back of the casing.
Do not caver or black tnem.
5. Avoidplacingthemonitornearheaters,stoves,replacesorothersources
of heat, as well as in rooms lacking adequate ventilation.
6. Do not in sert any objects or spray any liquids into the vents.
7. Do not position the monitor in unsafe locations. If the monitor falls, it may
be damaged and may injure nearby people.
8. Unplug the monitor if it is not going to be used for an extended period.
9. Do not place heavy objects on the monitor, its power cord or any
connected cables.
10. Do not open the back panel of the monitor, as it contains a high-voltage
current even when not plugged in.

3
A
CONTENTS
• Contents.....................................................................................03
• Components ............................................................................ 04
• Overview ................................................................................. 05
• Stand Assembly...................................................................... 06
• Wall Mounting..........................................................................08
• Connectivity............................................................................. 09
• Basic Operation.........................................................................11
• lndicator Light............................................................................11
• Operation.................................................................................... 12
• ECO Modes and Gameplus Switching .............................14
• Specications ............................................................................15
• Note ..............................................................................................16
Read all instructions before using the appliance and retain for reference.
1. Unplug the monitor before cleaning it with a slightly damp, clean cloth.
2. Wipingthescreenonceithasbeenturnedoffwithadrymicrobrecloth
is recommended.
3. The monitor is designed with ventilation holes in the back of the case.
Do not cover or block them
4. This monitor is designed with ventilation ho les on the back of the casing.
Do not caver or black tnem.
5. Avoidplacingthemonitornearheaters,stoves,replacesorothersources
of heat, as well as in rooms lacking adequate ventilation.
6. Do not in sert any objects or spray any liquids into the vents.
7. Do not position the monitor in unsafe locations. If the monitor falls, it may
be damaged and may injure nearby people.
8. Unplug the monitor if it is not going to be used for an extended period.
9. Do not place heavy objects on the monitor, its power cord or any
connected cables.
10. Do not open the back panel of the monitor, as it contains a high-voltage
current even when not plugged in.
SAFETY AND WARNINGS

4
USER MANUAL
OLRUN
Borderless wide screen
A
AMonitor
BMount
CStand Base
DPM4*12mm Screws (x2)
E26mm VESA connectors (x2)
F10mm VESA connectors (x2)
GPower Adapter
HHDMI Cable
IUser Guide
COMPONENTS
OVERVIEW
Monitor Controls
Monitor Ports

5
USER MANUAL
OLRUN
Borderless wide screen
F10mm VESA connectors (x2)
GPower Adapter
HHDMI Cable
IUser Guide
OVERVIEW
Monitor Controls
Menu Button: Press to display the OSD menu or enter sub-menus.
Down Button: Press to move down in the menus.
Up Button: Press to move up in the menus.
Exit Button: Press to exit.
Power Button: Press to turn the monitor on/off.
LED Indicator: Changes colors to indicate status.
A
Monitor Ports
Power Connector: Insert the power cable to supply power to the monitor.
Audio Output: lnsert one end of the Audio cable into the computer's Audio
output to receive the Audio signals from your monitor.
VGA Connector: lnsert one end of the VGA cable into the computer's VGA
output and connect the other end to the monitor's VGA port.
HDMI Connector: lnsert one end of the HDMI cable into the computer's HDMI
output and connect the other end to the monitor's HDMI port.

6
A
2.1
Align stand with
the base slot.
Keep the foam underneath the monitor before attaching the stand.
STAND ASSEMBLY
Stand Base
Foam
Stand Stem
Monitor
1. Open the package, take out the product with foam still attached,
and gently place it on a desktop or table.
2. Turn the bracket on a slight angle and align it with the circular slot
of the base. lnsert the bracket into the base, and then rotate clockwise
to clamp the bracket into the base to complete the installation of the base.
2.2
Keep the bracket
and the base
close, rotate the
bracket clockwise.
2.3
Make the bracket
click into the base.
2.4
lnsert screws to
base and tighten.
2.5
Complete stand and
base assembly.
3. Align the stand with the slot at the rear of the monitor, and insert the stand
into the monitor. To prevent damage during assembly, ensure the monitor is
still in the original foam.
Place Stand to the slot of monitor, and push up.

7
A
4. Complete overall assembly.
Note 1: To prevent pinching, please do not place your hand within
the gap between the stand and the monitor.
Note 2: To prevent falling, please avoid holding monitor by the
base or inverting the monitor.
Note: Do not invert the machine
to prevent falling.
To avoid damage, do not touch the screen when moving
the monitor.

8
A
WALL MOUNTING
1. Take out 4 pieces VESA connector frorn accessory bag.
Monitor
VESA Connector
2. Lock the two 26mm VESA connectors in the upper two ho les on the rear
of the monitor, and the two 10mm connectors in the lower two holes.
3. Your monitor is now ready to be attached to a wall-mounting bracket.
To avoid damage, please do not pinch the screen during bracket installation.
CONNECTIVITY
Power Cable
Connect the included power cable to the power connector and then plug
the other end to a wall plug .
Earphones
Plug in your earphones to receive audio signals from your monitor. If your
earphones are connected to the monitor and audio devices are connec-
ted to your computer at the same time, the audio devices will not produce
sound. Earphones and other audio devices not included.
VGA
ln order for the monitor to receive VGA signals from the computer, use a
VGA cable to connect the monitor to the computer.
Mount
(Not included)

9
A
CONNECTIVITY
Power Cable
Connect the included power cable to the power connector and then plug
the other end to a wall plug .
Earphones
Plug in your earphones to receive audio signals from your monitor. If your
earphones are connected to the monitor and audio devices are connec-
ted to your computer at the same time, the audio devices will not produce
sound. Earphones and other audio devices not included.
VGA
ln order for the monitor to receive VGA signals from the computer, use a
VGA cable to connect the monitor to the computer.
Power Cable
Earphones
(Not included)
VGA Cable
(Not included)
VGA OUTPUT

10
A
HDMI
ln order for the monitor to receive HDMI signals from the computer, use the
HDMI cable to connect the monitor to the computer.
HDMI Cable
(lncluded)
BASIC OPERATION
Solid blue light indicates power is on and the monitor is operating normally.
Flashing blue light indicates no video source has been detected. Red light
indicates that no horizontal or vertical signal has been detected or voltage
is low. Please ensure your computer is turned on and all video cables are
fully inserted and/or connected.
HDMI OUTPUT
1. Connect the other end of the cable to the corresponding connector
on your monitor.
2. Connect the power cab le to your monitor then connect the other end to
your power source. lt is recommended that you use a surge protector with
adequate voltage if a wall cannot be reached directly plug.
3. Locate the power button on the monitor and press it to turn the monitor on.
INDICATOR LIGHT