Kool karz playground Range rover sport svr User manual

MADE IN CHINA K07-SMS-156-002

002-01

Repair and Maintenance

1) The product contains electronic components and must not be used in water or in a damp

environment. Clean it with a piece of wet cloth.

2) Rotating parts should be checked regularly, to see whether they are jammed by any sundries

and to keep their normal lubricating state.

Land Rover and the Land Rover Logo are trademarks owned

and licensed by Jaguar Land Rover Limited. They are used by

Dongguan Chi Lok Bo Toys Company Limited under license.

Read Operation Instructions Carefully Before Use

Kool Karz Range Rover Sport SVR Electric Ride On

Dimensions of entire car

61.7CM

96.6CM

127.9CM

Contents

I. Product Specifications and Parameters

II. Components List

III. Assembly Diagram

IV. Installation and replacement of

remote control batteries

V. Function and Operation

VI. Battery and Charger Operating Guide

VII. Simple Fault Removal Guidance

VIII. Warning

I. Product Specifications and Parameters

1. This product is suitable for children 2-6 years old, and

should be used under adult supervision!

2. Product dimensions: 127.9 × 61.7 × 96.6CM

3. Product maximum load weight: 30 kg

4. Product charger: input AC 100-240V (50/60Hz), Output

(see charger parameters of the product)

5. Charging battery: (see the optional parameters) (1 battery) it can

provide about 200 cycles of charging and discharging

6. (Option B, Option D) Remote control and foot switch: 2.4G

one-to-one remote control

7. DC power supply of the remote controller: (see the optional

parameters) (the battery of this product is not included)

8. Product operating ambient temperature: 0-40℃

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Remote controllable

speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Remote controllable

speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Option A

DC 12V / 3.5 AH

DC 15V / 400 mA

DC 6V/15000r

(390 dual drive)

2.0 / 3.2 km/h

Option B

DC 12V / 3.5 AH

DC 15V / 400 mA

DC 6V/15000r

(390 dual drive)

2.0 / 3.2 km/h

1.7 / 2.4 / 3.2 km/h

Yes

2 × 1.5V AAA

Option C

DC 6V / 4.5 AH

DC 8V / 600 mA

DC 6V/15000r

(390 single driving)

2.0 / 2.7 km/h

Option D

DC 6V / 4.5 AH

DC 8V / 600 mA

DC 6V/15000r

(390 single driving)

2.0 / 2.7 km/h

1.7 / 2.2 / 2.7 km/h

Yes

2 × 1.5V AAA

MUSIC V

MP3

Voltage display

Next music

volume (+)

Pedal/high speed

button

Pedal/low speed

button

Horn button

Option C

One button start (main switch)

Music

Light button

MP3 interface

Previous music

volume (-)

MP3

MUSIC V

MP3

Optional D

Music

Light button

MP3 interface

Previous music

volume (-)

Voltage display

Next music volume (+)

Pedal/high speed

button

Pedal/low speed

button

Remote control

One button start (main switch)

1) One-button start button: ① Press this button to turn on the main power switch, the system will be in standby

mode, and the speaker will make a car engine sound. The One button start will glow

red and the Pedal/slow speed button will glow green, 00.00 and V are displayed on

the display, and the normal voltage is displayed after the end of the engine sound.

Then the English prompt sound is played by the music player, and the music button is

disabled until the prompt sound is over.

② After pressing and holding this button for 2 seconds, the main power will be cut off

and the system will be shut down.

2) Music button: Under MUSIC play mode, press this button to play a song, and the green light of this button is on;

press this button again to play the next song; there are 2 music buttons, each button will play 3

songs repeatedly.

3) Previous\Volume - Button:

(Option A, Option B)

(Option C, Option D)

①In MUSIC USB BT mode: short press this button, the green light of this button will

be on for a short period of time and it will change to the previous track; long press

this button for 2 seconds without release, the green light of this button will be on,

the volume will be lowered, the volume value on display will decrease from U30

to U00.

②Each time of starting, the default volume value will be U25.

①

②

MUSIC playback mode: short press this button, the green light of this button will

be on for a short period of time and it will change to the previous music;

MUSIC and MP3 playback mode: long press this button for 2 seconds without

releasing, the green light of this button will be on, the volume will be lowered, and

the volume value on the display will decrease from U30 to U00.

③Each time of starting, the default volume value will be U25.

2. Product warning:

1) There may be potential sharp edges, sharp points or small parts before the assembly of this

product is complete, this product must be assembled by an adult.

2) To avoid suffocation, keep plastic bagsaway from children. Dispose of all bags immediately.

3) The child must correctly use the car under adult guidance and supervision, to prevent

accidents to themselves and others.

4) The car is suitable for being driven on the flat ground and strictly prohibited to be driven in

dangerous places such as streets, roads, steep slopes and near swimming pools or water,

otherwise traffic or drowning accidents may occur.

5) Please put on shoes and protective equipment before use, such as fastening the seat belt

and putting on the helmet, gloves, knee pads, etc.

6) Small parts may possibly fall off when this product is used improperly. It is unsuitable for

children under 24 months old.

7) Regularly check whether the battery, charger, wire, plug, casing and other parts are

damaged; if damage occurs, please cease to use this product until it has been repaired.

8) This product is only allowed to be used by a child; the maximum load is 30kg, overload is

not allowed.

9) Keep away from fire.

10) Product instructions contain important information, please keep for future reference.

WARNING

To reduce the risk of injury, adult supervision is required.

Do not use on roadways, near motor vehicles, slopes, swimming pools

and where there is water.

Please wear shoes.

This toy car is only to be used by one person at a time.

Keep away from children before assembled by an adult, as there are

potentially sharp edges, points, or small parts.

Protective equipment should be worn. Not to be used in traffic.

Do not mix alkaline battery, standard (carbon-zinc) battery or rechargeable

(nickel-cadmium) battery.

IV. Installation and replacement of remote control batteries (Option B, Option D)

2.4G remote control

Glue on the screw

can prevent the

screw from dropping

out

Battery

Compartment

Battery Cover

2×1.5V AAA batteries

Unscrew the battery cover screws of the remote control (part 25), open the battery cover, find the positive and

negative poles, put 2 AAA batteries into the battery compartment, close the battery cover and fix it with screws.

V. Function and Operation

1. Main functions:

1) (Option B, Option D) Remote control and foot-pedal change-over switch

2) Rear drive: Power motor gearbox for powerful front/rear power.

3) Forward/backward function: The right side of the dashboard is provided with the three forward gears for

speed regulation, neutral gear, and reverse gear.

4) Foot pedal function: Press the foot pedal button, when the handle is in forward or backward position, step

down the foot pedal to move the car forward or backward, and release the foot switch to stop the car.

5) Charging protection function: Car will not power on while plugged in to charger to prevent damage and

accidents.

6) Forward/backward brake function: In forward or backward operation the car will brake when the foot pedal

is released

2. Functions on the central control board:

Option A

MUSIC V

USB

Music

Light button

Previous music

volume (-)

Voltage display

Next music

volume (+)

Pedal/high speed

button

Pedal/low speed

button

Horn button

USB interface

One button start (main switch)

MUSIC V

USB

Music

Light button

Previous music

volume (-)

Voltage display

Next music

volume (+)

Pedal/high speed

button

Pedal/low speed

button

Remote control

USB interface

Option B

One button start (main switch)

4) Previous\Volume + Button:

(Option A, Option B)

(Option C, Option D)

①MUSIC USB BT mode: Short press this button, it will switch to the next track;

long press this button for 2s, the green light of this button will be on, and the

volume will increase progressively, and the display volume value will increase

by U00-U30.

②Each time of starting, the default volume value will be U25.

①

②

MUSIC playback mode: short press this button, the green light of this button

will be on and it will change to the next track;

In MUSIC and MP3 playback mode: long press this button for 2 seconds without

releasing, the green light of this button will be on; the volume will increase, and

the volume value on display will be displayed incrementally from U00 to U30.

③Each time of starting, the default volume value will be U25.

(Optional A, Optional C)

(Optional B, Optional D)

①The power-on default mode is pedal/low-speed mode and the green light of

this button will glow. Step on the pedal to drive at a low speed, and release the

pedal to slowly brake and stop.

②Safety protection function: When stepping on foot pedal while starting the car,

you must first release the foot pedal and then step on it to start.

5) Lamp button: It is off when power-on. Press to turn on the car lamp, and the green light glow; press

again to turn off the car lamp and at this time the button green lamp is off.

6) Pedal/low speed button:

①The power-on default mode is pedal/low-speed mode and the green light of

this button will glow Step on the pedal to drive at a low speed, and release the

pedal to slowly brake and stop. Or you can press the emergency brake button

on the remote control to stop the brake. In the state of the emergency brake,

the car cannot be driven by stepping on the pedal.

②Safety protection function: When you step on the pedal while starting or

switching from the remote control mode to the low speed mode, you must first

release the pedal and then step on it again to drive.

(Optional A, Optional C)

(Optional B, Optional D)

7) Pedal/high speed button:

Press this button to switch to the pedal/high speed mode and the green light will

glow, then step on the pedal to drive at high speed, and release the pedal to

slowly brake and stop.

Press this button to switch to the pedal/high speed mode and the green light is on,

then step on the pedal to drive at high speed, and release the pedal to slowly

brake and stop. Or you can press the emergency brake button on the remote

control to stop the brake. In the state of the emergency brake, the car cannot be

driven by stepping on the pedal.

8) Horn button:

(Optional A, Optional C) Press this button to make a horn sound in any audio playback mode. Press

and hold this button to keep the horn sound ringing.

9) Remote control:

(Optional B, Optional D)

Press this button, the system will switch to remote control mode, and the

green light will be on; then use the remote control to start the car. (At this

time, the car can’t be started by only stepping on the accelerator pedal!)

10) Steering wheel button: ①The middle is the horn sound button, which will be sounded in any audio playback

mode; press and hold this button, the horn will sound continuously. ②The left button

and the right button are equivalent to the previous music\volume-button and the next

music\volume + function, etc on the switch board.

II. Components List

21. Rear mirror locknut

(4MM)

2PCS

11. Tail wing

1. Car Body

12. Window 22. Washer

4PCS

2. Windshield

23. Latch spring

4PCS

3. Steering Wheel 13. Rear wheel axle

24. Charger

4. Rear-view mirror 14. J-shaped stick

25. Remote

Control

5. Gear Handle 15. Steering gearbox screw

(3×10PWAB)

(D=10)

2PCS

26. Push handle

6. Wheel

2PCS

16. Steering wheel screw

(5×33PM)

27. MP3 connecting wire

(Option C, Option D)

7. Driving wheel

(with rubber

wheel sleeve)

2PCS

17. Rear-view mirror screw

(4×17PM)

2PCS

28. Plastic tube

(Option C, Option D)

8. Wheel cover

4PCS

18. Seat and backrest screw

(4×15TAB)

(D=7.5)

4PCS

9. Seat 19. Door screw

(3×10PAB)

12PCS

10. Seat backrest 20. Steering wheel locknut

(5MM)

11) Display:

(Optional A, Optional B)

(Optional C, Optional D)

Four digits display: ①The middle four digits display the voltage of the

battery in real time; it will display the volume change in adjusting the volume

(U00-U30); which song (0001-9999) in USB music will be displayed during

USB playback. ②The function icons on both sides of the display are

“MUSIC, USB, BT, V, ►, ”, and the mode or state in which it lies will be

displayed by its corresponding icon.

Four digits display: ①the middle four digits display the voltage of the battery

in real time; it will display the volume change in adjusting the volume

(U00-U30); which song (0001-9999) in USB music will be displayed during

USB playback ②The function icons on both sides of the display are

“MUSIC, MP3, ►, ”, and the mode or state in which it lies will be displayed

by its corresponding icon.

12) USB/Bluetooth playback function:

(Optional A, Optional B)

①When the machine is turned on without USB device inserted, it will enter the

built-in music playback mode, the English audio prompt “music player” will be

given out, and the display MUSIC will be always on. Then press the music

button to play the built-in music;

②Insert the USB device and the machine will be automatically switched to the

USB mode. The English audio prompt “USB mode” will be given out and the

display “USB” will be always on. After the prompt sound ends, the audio file in

the USB will be automatically played;

③When the machine is turned on with USB device inserted, it will automatically

enter the USB mode and automatically play the audio file in the USB. At this

time, the music button on the control panel is not functioned. When the USB is

pulled out, it will be automatically switched to the built-in music mode;

④When no USB device is inserted, bluetooth is in standby state at any time. When

being connected to a bluetooth device, the English audio prompt “bluetooth

mode” will be given out and the “BT” on the display will be always on. Then the

audio file in the bluetooth device can be played. At this time, the music button on

the central control panel is not functioned; when the bluetooth is disconnected,

there will be a beep sound. The machine will be automatically switched back to

the built-in music mode, “BT” on the display will be off and the “MUSIC” on.

(Bluetooth cannot be disconnected on the central control panel and can only be

disconnected on the external bluetooth device)

⑤When the USB device is inserted, the bluetooth cannot be connected. In other

words, USB device has priority.

⑥Name of Bluetooth: CHILOKBO

13) MP3 playback function:

(Optional C, Optional D)

①When the machine is turned on without MP3 cable connected, enter the MUSIC

built-in music playback mode, press the music button to play the built-in music.

At this time, plug in the MP3 cable, it will be automatically switched to MP3

mode and give out English prompt sound “MP3 mode”, and “MP3” on the display

will be always on, then you can play by connecting to an external sound source.

②When the machine is turned on with MP3 cable connected, it will automatically

enter the MP3 mode.

14) Sleep function: the system will enter sleep mode when it is without driving for 30 min, and the central

control board will automatically shut down, and all functions will turn off!

15) Low voltage protection function:

(Optional A, Optional B)

(Optional C, Optional D)

When the voltage is as low as 8.0V, the central control board will automatically

power off, and the car will stop automatically. Please charge as soon as possible!

When the voltage is as low as 4.5V, the central control board will automatically

power off, and the car will stop automatically. Please charge as soon as possible!

16) Charging and power-off function: When charging the car, the central control board will automatically power

off. All functions will be turned off, and the car cannot be started!

22 23

Gearbox Gearbox

Wheel with

rubber wheel

sleeve

Wheel with

rubber wheel

sleeve

Rear

wheel axle

Remarks: (Optional A, Optional C) don’t have steering gearbox

Put the wheel (part 6) and washer (part 22) into the front axle in sequence, clamp them into the groove

position of the axle with the latch spring (part 23) and fasten the wheel cover (part 8).

Rotate the motor gearbox upwards according to the direction indicated by the arrow until the motor

gearbox hole aligns with the car body axle hole, and then insert the rear axle (part 13) into the assigned

location of the car body.

Insert the rear wheel axle (part 13) into the assigned location of the car body, put the driving wheel (part

7) with rubber wheel ring and washer (part 22) into the front axle in sequence, clamp them into the

groove position of the axle with the latch spring (part 23) and fasten the wheel cover (part 8).

III. Assembly Diagram

1. Installation of wheels

(Option A, Option B)

1616 2020

Plug-in

Car body

hole

d with rubber sleeve and metal washer (part 22) into the rear axle in sequence, and clamp the assembled

Insert the rear wheel cartridge (part 28) into the rear axle, and then assemble the driv 7)

part into the groove of the rear axle with the retaining spring (part 23), and finally fasten the

wheel cover (part 8).

(Optional C, Optional D) Installation of Rear Wheel

2. Installation of J-shaped stick

(Optional B, Optional D) (Optional A, Optional C)

Insert the J-shaped iron hook (part 14) into the

designated position in front of the car.

Insert the J-shaped metal hook (part 14) into

the front gearbox, and then tighten it by using

the steering gearbox screw (part 15).

Plug the wire from the steering wheel into the wire

plug from the car body hole correspondingly, and

then put the connected plugs into the car body hole.

3. Installation of steering wheel and hand shank

Install the steering wheel (part 3) on the J-shaped

metal hook, and tighten with the steering wheel

screw (part 16) and the steering wheel locknut

(part 20); then insert the handle (part 5) into the

designated position and press down firmly to make

it reliably connected.

3. Normal operation:

1) Foot switch mode

A. Press the main power switch button

C. Select forward/reverse direction

B. Press the pedal low speed or high speed button

D. Step on the pedal to start the car

2) (Optional A, Optional B) Remote control pairing operation

A. Press the main power switch button to turn it on (pairing will be valid within two minutes after powering on)

B. Simultaneously keep pressing the speed change button and sudden brake button of the remote control for

5 seconds; if the lamp of first gear, second gear and third gear twinkles, it will indicate that the

code-matching action is transmitted; it will indicate that the codes are matched successfully until the lamp

is on and stops twinkling; when the pairing action is received, the front wheel will rotate leftwards for 1s

and rightwards for 1s.

3) (Optional B, Optional D) Remote control function

A. Forward/backward button B. Left/right movement button

C. Sudden brake button D. Speed change button

E. It will enter the sleep state if no operation occurs within 1 min. You can press any button to reawaken it.

(Optional A, Optional B)

(Optional C, Optional D)

Central

control board

Central

control board

Forward/backward

gear handle

(middle position for stop)

Footswitch

Forward/backward

gear handle

(middle position for stop)

Footswitch

Steering

Wheel

Previous music

volume (-) Horn button

Next music

volume (+)

Seat belt

Open

Buckle up

18 18

1010

18 18

11 12

Black cable

Blue cable

Battery

black-plug

(-) Battery

red-plug (+)

Red cable

Over-current

protection

Circuit board

placing box

Black cable

Battery

black-plug (-)

Battery

red-plug (+)

Red cable

Over-current

protection

Circuit board

placing box

Blue cable

4. Installation of power supply

(Optional A, Optional B) (Optional C, Optional D)

After installing the power supply, assemble the seat (part 9) on the specified position and tighten it with the

seat screw (part 18). Then mount the seat backrest (part 10) on the specified position and tighten it with the

seat backrest screw (part 18).

Insert plug (A) into the circuit board to its bottom. Insert plug (A) into the circuit board to its bottom.

5. Mount seat and seat backrest

6. Installation of tail wing 7. Install the window

Insert the window (part 12) into the designated position

on both sides of the car-body. Before installation,

please press each clip position to firmly connect.

Insert the tail wing (part 11) into the

corresponding hole along the arrow direction

and then tighten the screw.

SocketSocket Charging

plug

Charging

plug

VII. Simple Fault Removal Guidance

Trouble

1. The car cannot be started

2. Music sound is distorted

or silent

Key points of inspection

1) (Option A, Option B) Check if the battery is fully charged, and you can observe the

display of the central control panel to check whether the voltage is above 12V.

(Option C, Option D) Check if the battery is fully charged, and you can observe the

display panel of the central control panel to check the voltage is above 6V.

2) Check the power switch, all plugs of the dash receiver under the seat, and the battery

terminal line are properly inserted.

3) Check whether the circuit of the over-current protector is automatically disconnected

(when the motorcycle is overloaded and blocked, the circuit of the over-current

protector will be disconnected to protect the motor and dash receiver.)

4) Check whether the car has been stored for a long time and its battery is not

charged on time.

5) If the remote control cannot start the car, please check whether the remote control

pairing function is properly operated.

6) Check whether the remote control battery power is low.

Check whether the battery power is enough, and charge or replace the battery if not.

42.4G remote control First gear, second gear

and third gear lamps

Forward/backward button

Sudden brake button Speed change button

Left/right movement button

(Optional B, Optional D)

VI. Battery and Charger Operating Guide

Power Supply

Battery specifications

Over-current protection

Charging Source

Battery charging time for

every time

Chargeable type

(See the option parameters)

Input AC 100V-240V

50Hz/60Hz

Charging Time: 9-10 hours

Output (see charger parameters of the

product)

Utility time: 1-2 hours

1. The charging socket is located at the lower part of the car seat.

2. Only use battery and charger as recommended by the manufacturer.

3. Please do not play with the charger and battery because they are not toys.

The battery charging operation must be completed by adults only.

The battery shall be fully charged before first use, not

exceed 15 hours.

6. Charge immediately if the displayed voltage goes as low as

9.6V (Option A&B) or 4.8V (Option C&D).

7. The charger or battery may become warm during

operation, this is normal.

8. Install the rear-view mirror and windshield

Tighten with the door screws (part 19), as shown in

the figure2.

Assemble the rear-view mirror (part 4) on the

windshield, then tighten the rear-view mirror with

the screw (part 17) and the lock nut (part 21).

9. Open the car door

Install the windshield (part 2) at the assigned

location of the car front end, find each clip position

before installation, and then press it firmly until each

clip position is tight.

Push the switch in the car door panel forwards,

swing the car door outwards and open the car door.

10. Install pull grip

Press height

setting button

Push down

the push rod

Installer should stand at the rear of the car. As shown in

the figure, align with the the small bump at the bottom of

the push rod, hold the lower end of the push rod with

your left hand and push rod head with your right hand.

Press the push rod button with the thumb; Push down

the push rod with the right hand. observe and make

sure the two small bumps at the bottom end of the push

rod are completely retracted. At the same time, insert the

push rod into the bottom of the rear mounting hole.

When your here the click, then turn the push rod to

control the front wheel steering.

Blue cable

Circuit board

placing box

Black cable Battery black-plug (-)

Battery

red-plug (+)

Red cable

Over-current

protection

Blue cable

Black cable

Battery

red-plug (+)

Circuit board

placing box

Battery black-plug (-)

Red cable

Over-current

protection

Operation of overcurrent protector

1) The overcurrent protector is installed under the seat.

You can see it by removing the seat screw (as

shown in the figure) and taking the seat away.

2) When the car is overloaded, the overcurrent

protector automatically disconnects the circuit (for

protecting the circuit); when the circuit fault is

removed, the overcurrent protector automatically

connects the circuit.

3) When the battery has power and the car can not run,

please check whether the circuit of the car has an

open circuit or short circuit.

(Option A, Option B) (Option C, Option D)

Warning

Fire danger! The overcurrent

protection is only limited to 4A. Warning

Fire danger! The overcurrent

protection is only limited to 4A.

VIII. WARNING

1. Battery warning:

If the product is not used for a long time, please fully charge the battery and then turn off

the power switch for storing the car. The battery shall be recharged once every other month,

otherwise the battery service life will be shortened or the battery cannot be charged again.

Pay attention to the positive and negative terminals of the battery during installation (the

reverse connection or short circuit of the positive and negative terminals of the battery is not

allowed to occur).

Battery warning:

1) This product needs to be provided with two DC 1.5V AAA batteries (not included in this

product).

2) Pay attention to the positive and negative poles of the battery during installation (the

reverse connection or short circuit of the positive and negative poles of the battery is not

allowed to occur).

3) Rechargeable batteries charging operation can be carried out only by adults.

4) Non-rechargeable batteries cannot be charged.

5) The rechargeable batteries can be charged only after being taken out from the remote

control battery compartment.

6) Please do not mix different types of batteries or used batteries and new batteries.

7) If this product will not been used for a long time, the batteries shall be taken out from the

remote control battery compartment.

8) Exhausted batteries are to be removed from the toy.

2. Product warning:

1) There may be potential sharp edges, sharp points or small parts before the assembly of this

product is complete, this product must be assembled by an adult.

2) To avoid suffocation, keep plastic bagsaway from children. Dispose of all bags immediately.

3) The child must correctly use the car under adult guidance and supervision, to prevent

accidents to themselves and others.

4) The car is suitable for being driven on the flat ground and strictly prohibited to be driven in

dangerous places such as streets, roads, steep slopes and near swimming pools or water,

otherwise traffic or drowning accidents may occur.

5) Please put on shoes and protective equipment before use, such as fastening the seat belt

and putting on the helmet, gloves, knee pads, etc.

6) Small parts may possibly fall off when this product is used improperly. It is unsuitable for

children under 24 months old.

7) Regularly check whether the battery, charger, wire, plug, casing and other parts are

damaged; if damage occurs, please cease to use this product until it has been repaired.

8) This product is only allowed to be used by a child; the maximum load is 30kg, overload is

not allowed.

9) Keep away from fire.

10) Product instructions contain important information, please keep for future reference.

WARNING

To reduce the risk of injury, adult supervision is required.

Do not use on roadways, near motor vehicles, slopes, swimming pools

and where there is water.

Please wear shoes.

This toy car is only to be used by one person at a time.

Keep away from children before assembled by an adult, as there are

potentially sharp edges, points, or small parts.

Protective equipment should be worn. Not to be used in traffic.

Do not mix alkaline battery, standard (carbon-zinc) battery or rechargeable

(nickel-cadmium) battery.

IV. Installation and replacement of remote control batteries (Option B, Option D)

2.4G remote control

Glue on the screw

can prevent the

screw from dropping

out

Battery

Compartment

Battery Cover

2×1.5V AAA batteries

Unscrew the battery cover screws of the remote control (part 25), open the battery cover, find the positive and

negative poles, put 2 AAA batteries into the battery compartment, close the battery cover and fix it with screws.

V. Function and Operation

1. Main functions:

1) (Option B, Option D) Remote control and foot-pedal change-over switch

2) Rear drive: Power motor gearbox for powerful front/rear power.

3) Forward/backward function: The right side of the dashboard is provided with the three forward gears for

speed regulation, neutral gear, and reverse gear.

4) Foot pedal function: Press the foot pedal button, when the handle is in forward or backward position, step

down the foot pedal to move the car forward or backward, and release the foot switch to stop the car.

5) Charging protection function: Car will not power on while plugged in to charger to prevent damage and

accidents.

6) Forward/backward brake function: In forward or backward operation the car will brake when the foot pedal

is released

2. Functions on the central control board:

Option A

MUSIC V

USB

Music

Light button

Previous music

volume (-)

Voltage display

Next music

volume (+)

Pedal/high speed

button

Pedal/low speed

button

Horn button

USB interface

One button start (main switch)

MUSIC V

USB

Music

Light button

Previous music

volume (-)

Voltage display

Next music

volume (+)

Pedal/high speed

button

Pedal/low speed

button

Remote control

USB interface

Option B

One button start (main switch)

Dimensions of entire car

61.7CM

96.6CM

127.9CM

Contents

I. Product Specifications and Parameters

II. Components List

III. Assembly Diagram

IV. Installation and replacement of

remote control batteries

V. Function and Operation

VI. Battery and Charger Operating Guide

VII. Simple Fault Removal Guidance

VIII. Warning

I. Product Specifications and Parameters

1. This product is suitable for children 2-6 years old, and

should be used under adult supervision!

2. Product dimensions: 127.9 × 61.7 × 96.6CM

3. Product maximum load weight: 30 kg

4. Product charger: input AC 100-240V (50/60Hz), Output

(see charger parameters of the product)

5. Charging battery: (see the optional parameters) (1 battery) it can

provide about 200 cycles of charging and discharging

6. (Option B, Option D) Remote control and foot switch: 2.4G

one-to-one remote control

7. DC power supply of the remote controller: (see the optional

parameters) (the battery of this product is not included)

8. Product operating ambient temperature: 0-40℃

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Remote controllable

speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Remote controllable

speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Model:

Battery specifications:

Product charger:

Product drive motor:

Foot speed:

Over-current protection:

Remote Control:

Remote control DC

power supply:

Option A

DC 12V / 3.5 AH

DC 15V / 400 mA

DC 6V/15000r

(390 dual drive)

2.0 / 3.2 km/h

Option B

DC 12V / 3.5 AH

DC 15V / 400 mA

DC 6V/15000r

(390 dual drive)

2.0 / 3.2 km/h

1.7 / 2.4 / 3.2 km/h

Yes

2 × 1.5V AAA

Option C

DC 6V / 4.5 AH

DC 8V / 600 mA

DC 6V/15000r

(390 single driving)

2.0 / 2.7 km/h

Option D

DC 6V / 4.5 AH

DC 8V / 600 mA

DC 6V/15000r

(390 single driving)

2.0 / 2.7 km/h

1.7 / 2.2 / 2.7 km/h

Yes

2 × 1.5V AAA

MUSIC V

MP3

Voltage display

Next music

volume (+)

Pedal/high speed

button

Pedal/low speed

button

Horn button

Option C

One button start (main switch)

Music

Light button

MP3 interface

Previous music

volume (-)

MP3

MUSIC V

MP3

Optional D

Music

Light button

MP3 interface

Previous music

volume (-)

Voltage display

Next music volume (+)

Pedal/high speed

button

Pedal/low speed

button

Remote control

One button start (main switch)

1) One-button start button: ① Press this button to turn on the main power switch, the system will be in standby

mode, and the speaker will make a car engine sound. The One button start will glow

red and the Pedal/slow speed button will glow green, 00.00 and V are displayed on

the display, and the normal voltage is displayed after the end of the engine sound.

Then the English prompt sound is played by the music player, and the music button is

disabled until the prompt sound is over.

② After pressing and holding this button for 2 seconds, the main power will be cut off

and the system will be shut down.

2) Music button: Under MUSIC play mode, press this button to play a song, and the green light of this button is on;

press this button again to play the next song; there are 2 music buttons, each button will play 3

songs repeatedly.

3) Previous\Volume - Button:

(Option A, Option B)

(Option C, Option D)

①In MUSIC USB BT mode: short press this button, the green light of this button will

be on for a short period of time and it will change to the previous track; long press

this button for 2 seconds without release, the green light of this button will be on,

the volume will be lowered, the volume value on display will decrease from U30

to U00.

②Each time of starting, the default volume value will be U25.

①

②

MUSIC playback mode: short press this button, the green light of this button will

be on for a short period of time and it will change to the previous music;

MUSIC and MP3 playback mode: long press this button for 2 seconds without

releasing, the green light of this button will be on, the volume will be lowered, and

the volume value on the display will decrease from U30 to U00.

③Each time of starting, the default volume value will be U25.

18 18

1010

18 18

11 12

Black cable

Blue cable

Battery

black-plug

(-) Battery

red-plug (+)

Red cable

Over-current

protection

Circuit board

placing box

Black cable

Battery

black-plug (-)

Battery

red-plug (+)

Red cable

Over-current

protection

Circuit board

placing box

Blue cable

4. Installation of power supply

(Optional A, Optional B) (Optional C, Optional D)

After installing the power supply, assemble the seat (part 9) on the specified position and tighten it with the

seat screw (part 18). Then mount the seat backrest (part 10) on the specified position and tighten it with the

seat backrest screw (part 18).

Insert plug (A) into the circuit board to its bottom. Insert plug (A) into the circuit board to its bottom.

5. Mount seat and seat backrest

6. Installation of tail wing 7. Install the window

Insert the window (part 12) into the designated position

on both sides of the car-body. Before installation,

please press each clip position to firmly connect.

Insert the tail wing (part 11) into the

corresponding hole along the arrow direction

and then tighten the screw.

SocketSocket Charging

plug

Charging

plug

VII. Simple Fault Removal Guidance

Trouble

1. The car cannot be started

2. Music sound is distorted

or silent

Key points of inspection

1) (Option A, Option B) Check if the battery is fully charged, and you can observe the

display of the central control panel to check whether the voltage is above 12V.

(Option C, Option D) Check if the battery is fully charged, and you can observe the

display panel of the central control panel to check the voltage is above 6V.

2) Check the power switch, all plugs of the dash receiver under the seat, and the battery

terminal line are properly inserted.

3) Check whether the circuit of the over-current protector is automatically disconnected

(when the motorcycle is overloaded and blocked, the circuit of the over-current

protector will be disconnected to protect the motor and dash receiver.)

4) Check whether the car has been stored for a long time and its battery is not

charged on time.

5) If the remote control cannot start the car, please check whether the remote control

pairing function is properly operated.

6) Check whether the remote control battery power is low.

Check whether the battery power is enough, and charge or replace the battery if not.

42.4G remote control First gear, second gear

and third gear lamps

Forward/backward button

Sudden brake button Speed change button

Left/right movement button

(Optional B, Optional D)

VI. Battery and Charger Operating Guide

Power Supply

Battery specifications

Over-current protection

Charging Source

Battery charging time for

every time

Chargeable type

(See the option parameters)

Input AC 100V-240V

50Hz/60Hz

Charging Time: 9-10 hours

Output (see charger parameters of the

product)

Utility time: 1-2 hours

1. The charging socket is located at the lower part of the car seat.

2. Only use battery and charger as recommended by the manufacturer.

3. Please do not play with the charger and battery because they are not toys.

The battery charging operation must be completed by adults only.

The battery shall be fully charged before first use, not

exceed 15 hours.

6. Charge immediately if the displayed voltage goes as low as

9.6V (Option A&B) or 4.8V (Option C&D).

7. The charger or battery may become warm during

operation, this is normal.

1616 2020

Plug-in

Car body

hole

d with rubber sleeve and metal washer (part 22) into the rear axle in sequence, and clamp the assembled

Insert the rear wheel cartridge (part 28) into the rear axle, and then assemble the driv 7)

part into the groove of the rear axle with the retaining spring (part 23), and finally fasten the

wheel cover (part 8).

(Optional C, Optional D) Installation of Rear Wheel

2. Installation of J-shaped stick

(Optional B, Optional D) (Optional A, Optional C)

Insert the J-shaped iron hook (part 14) into the

designated position in front of the car.

Insert the J-shaped metal hook (part 14) into

the front gearbox, and then tighten it by using

the steering gearbox screw (part 15).

Plug the wire from the steering wheel into the wire

plug from the car body hole correspondingly, and

then put the connected plugs into the car body hole.

3. Installation of steering wheel and hand shank

Install the steering wheel (part 3) on the J-shaped

metal hook, and tighten with the steering wheel

screw (part 16) and the steering wheel locknut

(part 20); then insert the handle (part 5) into the

designated position and press down firmly to make

it reliably connected.

3. Normal operation:

1) Foot switch mode

A. Press the main power switch button

C. Select forward/reverse direction

B. Press the pedal low speed or high speed button

D. Step on the pedal to start the car

2) (Optional A, Optional B) Remote control pairing operation

A. Press the main power switch button to turn it on (pairing will be valid within two minutes after powering on)

B. Simultaneously keep pressing the speed change button and sudden brake button of the remote control for

5 seconds; if the lamp of first gear, second gear and third gear twinkles, it will indicate that the

code-matching action is transmitted; it will indicate that the codes are matched successfully until the lamp

is on and stops twinkling; when the pairing action is received, the front wheel will rotate leftwards for 1s

and rightwards for 1s.

3) (Optional B, Optional D) Remote control function

A. Forward/backward button B. Left/right movement button

C. Sudden brake button D. Speed change button

E. It will enter the sleep state if no operation occurs within 1 min. You can press any button to reawaken it.

(Optional A, Optional B)

(Optional C, Optional D)

Central

control board

Central

control board

Forward/backward

gear handle

(middle position for stop)

Footswitch

Forward/backward

gear handle

(middle position for stop)

Footswitch

Steering

Wheel

Previous music

volume (-) Horn button

Next music

volume (+)

Seat belt

Open

Buckle up

4) Previous\Volume + Button:

(Option A, Option B)

(Option C, Option D)

①MUSIC USB BT mode: Short press this button, it will switch to the next track;

long press this button for 2s, the green light of this button will be on, and the

volume will increase progressively, and the display volume value will increase

by U00-U30.

②Each time of starting, the default volume value will be U25.

①

②

MUSIC playback mode: short press this button, the green light of this button

will be on and it will change to the next track;

In MUSIC and MP3 playback mode: long press this button for 2 seconds without

releasing, the green light of this button will be on; the volume will increase, and

the volume value on display will be displayed incrementally from U00 to U30.

③Each time of starting, the default volume value will be U25.

(Optional A, Optional C)

(Optional B, Optional D)

①The power-on default mode is pedal/low-speed mode and the green light of

this button will glow. Step on the pedal to drive at a low speed, and release the

pedal to slowly brake and stop.

②Safety protection function: When stepping on foot pedal while starting the car,

you must first release the foot pedal and then step on it to start.

5) Lamp button: It is off when power-on. Press to turn on the car lamp, and the green light glow; press

again to turn off the car lamp and at this time the button green lamp is off.

6) Pedal/low speed button:

①The power-on default mode is pedal/low-speed mode and the green light of

this button will glow Step on the pedal to drive at a low speed, and release the

pedal to slowly brake and stop. Or you can press the emergency brake button

on the remote control to stop the brake. In the state of the emergency brake,

the car cannot be driven by stepping on the pedal.

②Safety protection function: When you step on the pedal while starting or

switching from the remote control mode to the low speed mode, you must first

release the pedal and then step on it again to drive.

(Optional A, Optional C)

(Optional B, Optional D)

7) Pedal/high speed button:

Press this button to switch to the pedal/high speed mode and the green light will

glow, then step on the pedal to drive at high speed, and release the pedal to

slowly brake and stop.

Press this button to switch to the pedal/high speed mode and the green light is on,

then step on the pedal to drive at high speed, and release the pedal to slowly

brake and stop. Or you can press the emergency brake button on the remote

control to stop the brake. In the state of the emergency brake, the car cannot be

driven by stepping on the pedal.

8) Horn button:

(Optional A, Optional C) Press this button to make a horn sound in any audio playback mode. Press

and hold this button to keep the horn sound ringing.

9) Remote control:

(Optional B, Optional D)

Press this button, the system will switch to remote control mode, and the

green light will be on; then use the remote control to start the car. (At this

time, the car can’t be started by only stepping on the accelerator pedal!)

10) Steering wheel button: ①The middle is the horn sound button, which will be sounded in any audio playback

mode; press and hold this button, the horn will sound continuously. ②The left button

and the right button are equivalent to the previous music\volume-button and the next

music\volume + function, etc on the switch board.

II. Components List

21. Rear mirror locknut

(4MM)

2PCS

11. Tail wing

1. Car Body

12. Window 22. Washer

4PCS

2. Windshield

23. Latch spring

4PCS

3. Steering Wheel 13. Rear wheel axle

24. Charger

4. Rear-view mirror 14. J-shaped stick

25. Remote

Control

5. Gear Handle 15. Steering gearbox screw

(3×10PWAB)

(D=10)

2PCS

26. Push handle

6. Wheel

2PCS

16. Steering wheel screw

(5×33PM)

27. MP3 connecting wire

(Option C, Option D)

7. Driving wheel

(with rubber

wheel sleeve)

2PCS

17. Rear-view mirror screw

(4×17PM)

2PCS

28. Plastic tube

(Option C, Option D)

8. Wheel cover

4PCS

18. Seat and backrest screw

(4×15TAB)

(D=7.5)

4PCS

9. Seat 19. Door screw

(3×10PAB)

12PCS

10. Seat backrest 20. Steering wheel locknut

(5MM)