Kraus Sellette KPF-1683SFS-KSD-80SFS User manual

Sellette Single Handle
Commercial Style Pull-Down
Kitchen Faucet
KPF-1683
TM
R
INSTALLATION MANUAL
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. April 6, 2022

Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement.
·Read all instructions and safety warnings and ensure you have all tools, parts, and
equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on the old faucet to
release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min) - 1 1/2" (max)
·Max countertop thickness without deck plate: 2 1/4”
·Max countertop thickness with deck plate: 1 3/4”
·1, 2 or 3 hole installation
STOP
R
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
ACID

44
Diagram and Parts List
1
2
8B
8A 9
3B
3A
4A
4C
4D
5
6
7
4B
10

55
Diagram and Parts List Tools you will need
1. Spray Head
2. Faucet Body
3. Deck Plate Assembly
A. Deck Plate
B. Base Plate
4. Mounting Hardware
A. Rubber Washer
B. Metal Washer
C. Mounting Nut
D. Mounting Screws
5. Spray Hose
6. Weight
7. Quick Connector
8. Hot and Cold Nylon Waterlines
A. Cold
B. Hot
9. Hex Wrench
10. Base O-Ring
Adjustable Wrench
Silicone Sealant
(optional)
Phillips Screwdriver
Safety Goggles
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
R

66
Installer Tip:
Shut off main water supply before installing new faucet.
Faucet Installation Procedure
8 5/8"
(220mm)
7"
(178mm)
23 1/4" (589mm)
8 3/4"
(223mm)
11 1/2" (292mm)
10 1/2"
(266mm)
* Optional Deck Plate
3/8" Compression
2 1/2"
(64mm)
Ø1 1/2" (37mm)
10 3/8"
(265mm)
1/2"
(13mm)
1/2"
(13mm)
10 3/4"
(273mm)
4 5/8"
(117mm)
MAX
2 1/4"
(57mm)

7
Step 1A. Faucet installation - with deck plate
Step 1B. Faucet installation - without deck plate
For three-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
(optional) are required.
For single-hole installation:
Deck plate (3A), base plate
(3B) and silicone sealant
are NOT required.
3A
3B

8
Step 2. Install faucet and mounting hardware
Step 3. Secure mounting hardware
Insert faucet body (2) into
hole in countertop or deck
plate assembly (3). Install
mounting hardware (4A, B, C & D)
from underneath the
countertop.
Adjust direction of faucet
body (2) so that handle is on
right side of faucet. Tighten
mounting nut (4C) until snug.
Tighten mounting screws
(4D) to nut with a Phillips
screwdriver until snug.
4A
4C
4D
4C
4D
4B

9
Step 4. Attach spray hose and counterweight
Step 5. Connect waterlines
Connect spray hose (5)
to quick connector (7)
attached to supply line.
Install weight (6) on lowest
vertical point on spray
hose (5).
Connect waterlines (8) to angle
stops. Tighten both ends of
waterlines with a wrench
until snug. Turn on hot and
cold angle stops and check
for leaks.
7
5
6
8
NOTE: Make sure filter
washers are installed.

10
Step 6. Flush spray hose
Remove spray head (1) from
spray hose (5). Hold tip of
spray hose (5). Turn faucet on
and let the water run for 60
seconds to flush any debris.
Step 7. Check for leaks
Check for leaks at the
connections. Retighten if
necessary.
NOTE: Please make sure washer is
installed attaching spray head to hose.
5
1