Kraus KPF-1603CH User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. December 10, 2020
Artec ProTM 2 Function
Commercial Style
Kitchen Faucet
KPF-1603
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 2 3/8”
3
Tools Required
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Adjustable Wrench Phillips Screwdriver Silicone Sealant
Safety Goggles Pipe Tape

44
Diagram and Parts List
A. Faucet Body
B1. Seat
B2. Rubber Washer
B3. Metal Washer
B4. Mounting Nut
B5. Screw
C. Hex Wrench
A
B1
B2
B3
B4
B5
C

55
Faucet Installation Procedure
Installer Tip:
Shut off main water supply before installing new faucet.
3/8" Compression
4 1/8"
(106.5mm)
24 3/4"
(628.7mm)
2 3/8"
(60mm)
MAX.
2 3/8"
(60.8mm)
6 5/8"
(173.3mm)
9 3/4"
(248.2mm)
7 1/8"
(182.6mm)
7 5/8"
(198.2mm)
6"
(153.2mm)

66
Step 1. Remove washer and lock nut
Step 2. Install faucet
Shut off the water supply.
Remove the old faucet. Clean the
mounting surface. Remove
mounting hardware (B) from
faucet body (A).
Insert faucet through hole in sink
or countertop.From underneath
sink, attach the seat (B1), rubber
washer (B2), metal washer (B3),
and nut (B4). Lock nut (B4) into
position by tightening screws (B5).
A
B
B1
B2
B3
B4 B5

7
Step 3. Making the water supply connections
Push the quick connector (2)
firmly upward and attach it to the
receiving block (1). Pull down
moderately to ensure the
connection has been made.
If it is necessary to remove the
quick connector (2), squeeze the
tabs on the hose and then pull
down to disconnect.
Step 4. Making the water supply connections
Thread the nut (1) on the supply
line onto the outlet of the water
supply valve and tighten with a
wrench. Do not overtighten.
1
2
1

8
Step 5. Flushing and checking for leaks
Pull the hose assembly out of the
spout and remove the spray head
by unscrewing it from the hose in
a counterclockwise direction. Be
sure to hold the end of the hose
down into the sink and turn the
faucet on to the warm position
where it mixes hot and cold
water.
Flush the water lines for one
minute. This flushes away any
debris that could cause damage
to internal parts. Check for leaks.
Reinstall the spray head by hand
tightening it back onto the spray
hose.
1
2
NOTE:
1. Do not lose the rubber washer (1)
when installing the sprayer back on.
2. The magnet end marking with a
black dot should be toward the hose
for correct magnet installation.

9
Step 6. Flush faucet
To activate the spray mode, simply
press the handle (1) located under
the spray head.
1

10
Replacement Parts
Replacement Parts List Finish/Color Part #
KP27060
KP27061
KP27062*
KP27063
KP27080
KP27064
KP27065
KP27066
KP27067
KP27068
KP27069
KP27070
KP27071
KP27072
KP27028
KP27079
KP27073
KP27077
KP27078
KP27074
KP27076
KP27020
CH,SFS,SBBG,SFSB,SFACB,
MBSB,BG,SFSMB,BGMB**
4
5
1
2
3
9
10
18
19
20
21
16
15
17
11
14.3
14.1
22
14.2
6
7
8
*Denotes spray hose assembly color options:
Spray hose assembly color options: Black
hose w/ Brushed Gold connector (BLBG),
Black hose with Spot-Free Stainless
connector (BLSFS), Black hose with Black
Stainless connector (BLSB), Gray hose with
Chrome connector (GRCH), Gray hose with
Spot-Free Stainless connector (GRSFS)
**Denotes faucet component color options:
CH - Chrome
SFS - Spot Free Stainless Steel
MB - Matte Black
BG - Brushed Gold
SB - Black Stainless
SFACB - Spot Free Antique Champagne Bronze
SFSB - Spot Free Black Stainless
BL - Black
WH - White
1213
1. Spray Head
2. Magnet
3. Spray Hose
Assembly
4. Spring
5. Inverter
6. Spray Support
Assembly
7. Spout Nut
8. Spout
9. Diverter
10. Aerator Assembly
11. Cartridge
12. Bonnet Nut
13. Cap
14. Handle Assembly
15. Rubber & Metal
Washer
16. Mounting Nut & Nut
17. Block
18. Flange
19. Seat
20. 1.8GPM Flow
Restrictor
21. Quick Connect
22. Hex Wrench
WH**
BLBG,BLSFS,BLSB,BLSFACB
GRCH,GRSFS,BLSFSB**
CH,SFS,BG,SB,SFACB,SFSB**
CH,SFS,BG,
MB,SB,SFACB,SFSB**
CH,SFS,SB,BG,MB,
SFACB,SFSB**
CH,SFS,BG,MB,SB,
SFACB,SFSB**
CH,SFS,BG,MB,SFACB**
CH,SFS,BG,MB,SFACB**
CH,SFS,BG,SB,SFACB,SFSB**
CH,SFS,SBBG,SB,BG,
SFSMB,BGMB,SFACB,SFSB**