KROHNE SMARTMAC 200 W User manual

Operating and display unit
for SMARTPAT PH/ORP/COND sensors
Electronic Revision: ER 2.0.X_
SMARTMAC 200 W
SMARTMAC 200 WSMARTMAC 200 W
SMARTMAC 200 W Handbook
HandbookHandbook
Handbook
© KROHNE 09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
The documentation is only complete when used in combination with the relevant
documentation for the sensor.

All rights reserved. It is prohibited to reproduce this documentation, or any part thereof, without
the prior written authorisation of KROHNE Messtechnik GmbH.
Subject to change without notice.
2
www.krohne.com 09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
Copyright 2017 by
KROHNE Messtechnik GmbH - Ludwig-Krohne-Str. 5 - 47058 Duisburg (Germany)
: IMPRINT :::::::::::::::::::::::::::::::::::::::

CONTENTS
3
www.krohne.com09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
SMARTMAC 200 W
1 Safety instructions 5
1.1 Software history ............................................................................................................... 5
1.2 Intended use ..................................................................................................................... 5
1.3 Certifications .................................................................................................................... 6
1.4 Safety instructions from the manufacturer ..................................................................... 7
1.4.1 Copyright and data protection ................................................................................................ 7
1.4.2 Disclaimer ............................................................................................................................... 7
1.4.3 Product liability and warranty ................................................................................................ 8
1.4.4 Information concerning the documentation........................................................................... 8
1.4.5 Warnings and symbols used................................................................................................... 9
1.5 Safety instructions for the operator................................................................................. 9
2 Device description 10
2.1 Scope of delivery............................................................................................................. 10
2.2 Device description .......................................................................................................... 11
2.3 Nameplate ...................................................................................................................... 12
3 Installation 13
3.1 General notes on installation ......................................................................................... 13
3.2 Storage and transport .................................................................................................... 13
3.3 Point-to-Point connection - analogue / digital mode .................................................... 14
3.4 Pre-installation requirements ....................................................................................... 15
3.5 Wall mounting ................................................................................................................ 16
4 Electrical connections 19
4.1 Safety instructions.......................................................................................................... 19
4.2 Important device-specific notes on electrical connection............................................. 19
4.3 Opening and closing the converter housing .................................................................. 20
4.3.1 Die-cast aluminium housing................................................................................................. 20
4.3.2 Stainless steel converter housing ........................................................................................20
4.4 Connection assignment.................................................................................................. 21
4.5 Connecting the sensor cable.......................................................................................... 22
4.6 Connection diagram overview ........................................................................................ 22
4.7 Power supply .................................................................................................................. 23
5 Operation 25
5.1 Operating elements........................................................................................................ 25
5.2 Measuring mode.............................................................................................................26
5.2.1 Error page pH........................................................................................................................ 27
5.2.2 Error page ORP ..................................................................................................................... 28
5.2.3 Error page conductive conductivity ...................................................................................... 29
5.3 Menu mode ..................................................................................................................... 29
5.4 Menu mode structure pH ............................................................................................... 30
5.4.1 Function table pH measurement.......................................................................................... 31

CONTENTS
4
www.krohne.com 09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
SMARTMAC 200 W
5.4.2 pH calibration........................................................................................................................ 37
5.5 Menu mode structure ORP............................................................................................. 39
5.5.1 Function table ORP measurement ....................................................................................... 40
5.5.2 ORP calibration ..................................................................................................................... 46
5.6 Menu mode structure conductivity ................................................................................ 47
5.6.1 Function table conductivity measurement........................................................................... 48
5.6.2 Conductivity calibration ........................................................................................................ 54
6 Service 61
6.1 Maintenance and repair ................................................................................................. 61
6.2 Availability of services .................................................................................................... 61
6.3 Returning the device to the manufacturer..................................................................... 61
6.3.1 General information.............................................................................................................. 61
6.3.2 Form (for copying) to accompany a returned device............................................................ 62
6.4 Disposal .......................................................................................................................... 62
7 Technical data 63
7.1 Technical data................................................................................................................. 63
7.2 Dimensions ..................................................................................................................... 65
7.2.1 Housing die-cast aluminium................................................................................................. 67
7.2.2 Housing stainless steel......................................................................................................... 68
7.2.3 Mounting plate die-cast aluminium ..................................................................................... 69
7.2.4 Mounting plate stainless steel.............................................................................................. 70
8 Notes 71

SAFETY INSTRUCTIONS 1
5
SMARTMAC 200 W
www.krohne.com09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
1.1 Software history
Changes and effect on compatibility
1.2 Intended use
INFORMATION!
In the table below, "x" is a placeholder for possible multi-digit alphanumeric combinations,
depending on the available version.
1Downwards compatible changes and fault repair with no effect on operation (e.g. spelling
mistakes on display)
2-_ Downwards compatible hardware and/or software change of interfaces:
HHART
®
PPROFIBUS
FFoundation Fieldbus
MModbus
Xall interfaces
3-_ Downwards compatible hardware and/or software change of inputs and outputs:
ICurrent output
F, P Frequency / pulse output
SStatus output
CControl input
CI Current input
Xall inputs and outputs
4Downwards compatible changes with new functions
5Incompatible changes, i.e. electronic equipment must be changed.
Release date Electronic
revision
Changes and
compatibility
Documentation
2015-10-01 ER 1.0.X_ -MA SMARTMAC 200 W R01
2016-05-25 ER 1.1.X 4MA SMARTMAC 200 W R02
2017-09-04 ER 2.0.X_ 5MA SMARTMAC 200 W R03
DANGER!
For devices used in hazardous areas, additional safety notes apply; please refer to the Ex
documentation.
CAUTION!
Responsibility for the use of the measuring devices with regard to suitability, intended use and
corrosion resistance of the used materials against the measured fluid lies solely with the
operator.
WARNING!
If the device is not used according to the operating conditions (refer to chapter "Technical data"),
the intended protection could be affected.

1 SAFETY INSTRUCTIONS
6
SMARTMAC 200 W
www.krohne.com 09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
SMARTMAC 200 W is a loop-powered operating unit with display. The intended use of the
SMARTMAC 200 W is to configure and calibrate the SMARTPAT PH, ORP or COND sensors in
field.
1.3 Certifications
The device meets the essential requirements of the EU directives. The CE marking indicates the
conformity of the product with the union legislation applying to the product and providing for CE
marking.
For full information of the EU directives and standards and the approved certifications, please
refer to the EU declaration on the KROHNE website
Other approvals and standard
•NAMUR recommendation NE 21
INFORMATION!
This device is a Group 1, Class A device as specified within CISPR11:2009. It is intended for use in
industrial environment. There may be potential difficulties in ensuring electromagnetic
compatibility in other environments, due to conducted as well as radiated disturbances.
INFORMATION!
The manufacturer is not liable for any damage resulting from improper use or use for other than
the intended purpose.
CE marking

SAFETY INSTRUCTIONS 1
7
SMARTMAC 200 W
www.krohne.com09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
1.4 Safety instructions from the manufacturer
1.4.1 Copyright and data protection
The contents of this document have been created with great care. Nevertheless, we provide no
guarantee that the contents are correct, complete or up-to-date.
The contents and works in this document are subject to copyright. Contributions from third
parties are identified as such. Reproduction, processing, dissemination and any type of use
beyond what is permitted under copyright requires written authorisation from the respective
author and/or the manufacturer.
The manufacturer tries always to observe the copyrights of others, and to draw on works created
in-house or works in the public domain.
The collection of personal data (such as names, street addresses or e-mail addresses) in the
manufacturer's documents is always on a voluntary basis whenever possible. Whenever
feasible, it is always possible to make use of the offerings and services without providing any
personal data.
We draw your attention to the fact that data transmission over the Internet (e.g. when
communicating by e-mail) may involve gaps in security. It is not possible to protect such data
completely against access by third parties.
We hereby expressly prohibit the use of the contact data published as part of our duty to publish
an imprint for the purpose of sending us any advertising or informational materials that we have
not expressly requested.
1.4.2 Disclaimer
The manufacturer will not be liable for any damage of any kind by using its product, including,
but not limited to direct, indirect or incidental and consequential damages.
This disclaimer does not apply in case the manufacturer has acted on purpose or with gross
negligence. In the event any applicable law does not allow such limitations on implied warranties
or the exclusion of limitation of certain damages, you may, if such law applies to you, not be
subject to some or all of the above disclaimer, exclusions or limitations.
Any product purchased from the manufacturer is warranted in accordance with the relevant
product documentation and our Terms and Conditions of Sale.
The manufacturer reserves the right to alter the content of its documents, including this
disclaimer in any way, at any time, for any reason, without prior notification, and will not be liable
in any way for possible consequences of such changes.

1 SAFETY INSTRUCTIONS
8
SMARTMAC 200 W
www.krohne.com 09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
1.4.3 Product liability and warranty
The operator shall bear responsibility for the suitability of the device for the specific purpose.
The manufacturer accepts no liability for the consequences of misuse by the operator. Improper
installation or operation of the devices (systems) will cause the warranty to be void. The
respective "Standard Terms and Conditions" which form the basis for the sales contract shall
also apply.
1.4.4 Information concerning the documentation
To prevent any injury to the user or damage to the device it is essential that you read the
information in this document and observe applicable national standards, safety requirements
and accident prevention regulations.
If this document is not in your native language and if you have any problems understanding the
text, we advise you to contact your local office for assistance. The manufacturer can not accept
responsibility for any damage or injury caused by misunderstanding of the information in this
document.
This document is provided to help you establish operating conditions, which will permit safe and
efficient use of this device. Special considerations and precautions are also described in the
document, which appear in the form of icons as shown below.

SAFETY INSTRUCTIONS 1
9
SMARTMAC 200 W
www.krohne.com09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
1.4.5 Warnings and symbols used
Safety warnings are indicated by the following symbols.
• HANDLING
HANDLINGHANDLING
HANDLING
This symbol designates all instructions for actions to be carried out by the operator in the
specified sequence.
iRESULT
RESULTRESULT
RESULT
This symbol refers to all important consequences of the previous actions.
1.5 Safety instructions for the operator
DANGER!
This warning refers to the immediate danger when working with electricity.
DANGER!
This warning refers to the immediate danger of burns caused by heat or hot surfaces.
DANGER!
This warning refers to the immediate danger when using this device in a hazardous atmosphere.
DANGER!
These warnings must be observed without fail. Even partial disregard of this warning can lead to
serious health problems and even death. There is also the risk of seriously damaging the device
or parts of the operator's plant.
WARNING!
Disregarding this safety warning, even if only in part, poses the risk of serious health problems.
There is also the risk of damaging the device or parts of the operator's plant.
CAUTION!
Disregarding these instructions can result in damage to the device or to parts of the operator's
plant.
INFORMATION!
These instructions contain important information for the handling of the device.
LEGAL NOTICE!
This note contains information on statutory directives and standards.
WARNING!
In general, devices from the manufacturer may only be installed, commissioned, operated and
maintained by properly trained and authorized personnel.
This document is provided to help you establish operating conditions, which will permit safe and
efficient use of this device.

2 DEVICE DESCRIPTION
10
SMARTMAC 200 W
www.krohne.com 09/2017 - 4003047503 - MA SMARTMAC 200 W R03 en
2.1 Scope of delivery
INFORMATION!
Inspect the packaging carefully for damages or signs of rough handling. Report damage to the
carrier and to the local office of the manufacturer.
INFORMATION!
Do a check of the packing list to make sure that you have all the elements given in the order.
INFORMATION!
Look at the device nameplate to ensure that the device is delivered according to your order.
Check for the correct supply voltage printed on the nameplate.
Figure 2-1: Standard scope of delivery
1 Ordered device
2 Documentation