Kurzweil KME-61 VERSION 2 SOFTWARE Owner's manual

1
KME-61 VERSION 2 SOFTWARE SUPPLEMENT
-Jan. 2004-
• What Is It?
Software version v2 is the latest set of feature enhancements for the KME-61 keyboard.
• What Does It Do? (i.e. what are the new features in v2?)
v2 adds new controller features to the KME-61:
-the ability to program independent controller assignments per zone within a setup.
See the section below marked “Additional features added in v2” for operational details.
• How Do I Know If I Have v2?
If you received this document along with the purchase of a KME-61, then the v2 software
should already be installed in your unit. If you did not receive this document along with your
instrument or if you just want to confirm things, you can check what version of software you
currently have installed by doing the following:
1) turn KME-61 on
2) while powering up, you will see the current software revisions installed in your unit
3) if your unit has v2 (front software), you will see the following in the display:
• Where Can I Get It If I Don’t Have It?
Please visit your local authorized Kurzweil Music Systems service center to have v2 installed.
To locate a service center near you please visit our website at:
http://www.kurzweilmusicsystems.com/support-service-center-search.html?Id=296
For further information please contact:
Email= [email protected]
Web= www.kurzweilmusicsystems.com
FRONT VER 2.01
ENGINE VER 1.10

KME-61 Addendum
2
Additional features added in v2
Per Zone Controller Assignments:
When in Setup Mode, using the previous v1.xx software, all physical controllers, including the
optional pedals, worked the same for all zones simultaneously and were always enabled. To
improve live performance usefulness, Version 2 software allows controllers to be reassigned
or turned off on a per-zone basis. This is accomplished by adding several parameters to the
Setup Mode Menu which are described below.
Setup Edit Pages (new v2 parameters in BOLD)
1. Edit Sound Select
2. Edit Key Range Low, High
3. Edit Note Shift
4. Edit Vel. Range Low, High
5. Edit Volume
6. Edit Effects Type
7. Edit FX A, FX B Level
8. Edit MIDI Channel
9. Edit MIDI Bank, Program
10. Edit MIDI Volume
11. Edit Mono Pressure
12. Edit Pitch Wheel
13. Edit Data Slider
14. Edit Modulation Wheel (Mod Wheel)
15. Edit Continuous Controller Pedal (CC Pedal)
16. Edit Switch Pedal (SW Pedal)
Detailed Parameter Descriptions:
Mono Pressure (Keyboard Aftertouch) and Pitch Wheel controllers only have an on/off
parameter.
11. Mono Pressure
In Setup Edit Mode, press the Menu Down button 14 times or hold until the Edit Mono
Pressure screen appears as below.
This screen allows you to turn Mono Pressure on or off for each zone easily. First select the
zone, 1, 2, or 3 by pressing one of the soft buttons under the display. The selected zone is
shown in the upper left corner of the display. Then use the + button to turn On or - button to
turn Off Mono Pressure in that zone.
Z1:Edit Mono Press
MPress: On

3
12. Pitch Wheel
Press the Menu Down button once again to see the Edit Pitch Wheel screen.
This parameter allows you select which zones are affected by the pitch wheel.
Select the zone and on/off setting as with Mono Pressure described above.
Each of the remaining controllers has two parameters: MIDI Controller Number and Entry
Value which is the initial value sent when the setup is selected.
13.Data Slider
The next screen after Edit Pitch wheel (see above) is Edit Data Slider.
You can move the indicator (->) to select the MIDI Controller Number (CtrN) or Entry Value
(EntV) by using the Menu Up/Down buttons. Select the zone with the soft buttons under the
display and change the value with the + and – buttons OR by moving the front panel “Data
Slider”.
CtrN can have values of 1-119. EntV can have values of 1-127. The default CtrN for the data
slider is 6, MIDI Data Entry.
Additionally, each parameter can have a value of "None". When you choose a value of
"None", it has a special function.
If CtrN is set to None, the controller will not send any MIDI messages for the zone and will not
affect the sound of the program selected for the zone.
If EntV is set to None, the entry value will be the current value (physical position) of the data
slider
14. Modulation Wheel (Mod Wheel)
The next screen after Edit Pitch Wheel is Edit Mod Wheel. Press the Menu Down button once
or twice to reach it.
The parameters, editing method and available values are the same as for the data slider.
The default MIDI Controller Number for Modulation wheel is 1 (Mod Wheel)
15. Continuous Controller Pedal (CC Pedal)
The next screen after Edit Mod Wheel is Edit CC Pedal. Press the Menu Down button once
or twice to reach it.
Z1:Edit Pitch Wheel
PWheel: On
Z1:Edit Data Slide
CtrN:6 EntV:None
Z1:Edit Mod Wheel
CtrN:1 EntV:None
Z1:Edit CC Pedal
CtrN:11 EntV:None

KME-61 Addendum
4
The parameters, editing method and available values are the same as for the data slider.
The default MIDI Controller Number for CC Pedal is 11 (Expression).
Please pay special attention to the Entry Value for this parameter. If it is set to a small value
or Zero, the zone will be silent until the CC pedal is moved. If it is set to a high value or 127,
the zone may play much louder than expected.
16. Switch Pedal (SW Pedal)
The next screen after Edit CC Pedal is Edit SW Pedal. Press the Menu Down button once or
twice to reach it.
The parameters, editing method and available values are the same as for the data slider.
The default MIDI Controller Number for SW Pedal is 64 (Sustain Pedal). As this is a “switch
type” controller, entry values of 63 or less are treated as "Off". Entry values of 64 or more are
treated as "On".
Compatibility between V1.xx and V2 front software
Version 2 front software can import setups saved from v1.xx.
However, v1.xx cannot import v2 setups, because of their increased size.
Z1:Edit SW Pedal
CtrN:64 EntV:None