Kyocera ECOSYS M6026cidn User manual

Projekt CAMPUS dB
Kyocera ECOSYS M6026/M6526cidn
Lufthansa Systems Infratec GmbH
Object: Technical Documentation
Author: Dirk Czichon
Signed off by: Manuel Siefker
Version: 1.0
Valid from: 05.07.2014

Projekt CAMPUS dB
Technical Documentation
Kyocera ECOSYS M6026/M6526cidn
FRA AI/M-D
Author(s): Dirk Czichon
File: CdBTD_Kyocera_EcoSys-M6026M6526cidn.doc
Signed off by:
Manuel Siefker
Version: 1.0
Page 2 of 6
Valid from: 05.07.2014
Vorlage 14.07.2004
Table of Contents
1Introduction.................................................................................................................... 3
1.1 Requirements.......................................................................................................... 3
1.2 Interfaces................................................................................................................ 3
2Putting into Operation..................................................................................................... 4
2.1 Set up the network connection using a suitable network cable................................ 4
2.2 Set up some printer settings.................................................................................... 4
2.3 Set up the network settings..................................................................................... 4
2.4 Restart the printer ................................................................................................... 6
2.5 Handover to ServiceDesk or RolloutControlCenter.................................................. 6

Projekt CAMPUS dB
Technical Documentation
Kyocera ECOSYS M6026/M6526cidn
FRA AI/M-D
Author(s): Dirk Czichon
File: CdBTD_Kyocera_EcoSys-M6026M6526cidn.doc
Signed off by:
Manuel Siefker
Version: 1.0
Page 3 of 6
Valid from: 05.07.2014
Vorlage 14.07.2004
1 Introduction
This document describes the putting into operation and minimum configuration of the printer
Kyocera ECOSYS M6026cidn and M6526cidn. This color printer can be used in a network
and has a Duplex Print option.
Additionaly this multi-function-printer can be used for direct paper copies (even without cable).
The function Scan2mail is possible, but not part of this document.
The function FAX is possible (with M6526cidn), but not part of this document.
1.1 Requirements
Network printing via TCP/IP.
Local printing via USB cable.
1.2 Interfaces
Scan2mail is supported by mail services.
FAX is supported by telefon services.

Projekt CAMPUS dB
Technical Documentation
Kyocera ECOSYS M6026/M6526cidn
FRA AI/M-D
Author(s): Dirk Czichon
File: CdBTD_Kyocera_EcoSys-M6026M6526cidn.doc
Signed off by:
Manuel Siefker
Version: 1.0
Page 4 of 6
Valid from: 05.07.2014
Vorlage 14.07.2004
2 Putting into Operation
Set up the printer according to the instructions supplied by the manufacturer and put it into
operation. See “ECOSYS_M6026cidn_M6526cidn_OG_ENG.pdf “ provided by Kyocera.
Some excerpts are added in the appendix of this document.
2.1 Set up the network connection using a suitable network cable.
Connect printer with CAT5e or CAT6 cable to the LAN outlet according to order.
Check LAN connectivity with the LED’s at the printers RJ45 plug.
2.2 Set up some printer settings
Press the Button “System Menu / Counter” see Page 9-3
Login
The user and password for the “DeviceAdministrator” is 2600 see Page 9-2
Scroll and select Printer see Page 9-17
Scroll and select “Emulation”, if not allready set to KPDL(Auto)
Scroll and select “Override A4/Letter”, if not allready set to ON
Scroll and select “Wide A4”, set according to order
Scroll and select “Job Name”, if not allready set to OFF
Scroll and select “User Name”, if not allready set to OFF
Leave this level “ <”
2.3 Set up the network settings
Scroll and select System
Scroll and select Network see Page 9-19
Select Host Name
and enter the printers networkname NP………
Scroll and select “TCP/IP Settings”
Scroll and select “TCP/IP”, if not allready set to ON
Scroll and select “IPv4 Settings”
Scroll and select “DHCP”, set according to the order (in remote locations: OFF )
Scroll and select “Auto-IP”, if not allready set to OFF

Projekt CAMPUS dB
Technical Documentation
Kyocera ECOSYS M6026/M6526cidn
FRA AI/M-D
Author(s): Dirk Czichon
File: CdBTD_Kyocera_EcoSys-M6026M6526cidn.doc
Signed off by:
Manuel Siefker
Version: 1.0
Page 5 of 6
Valid from: 05.07.2014
Vorlage 14.07.2004
Scroll and select “IP-Address”, set according to order xx.xxx.xxx.xxx
Scroll and select “Subnet Mask”, set according to order 255.255.xxx.xxx
Scroll and select “Default Gateway”, set according to order xx.xxx.xxx.x
Leave this level “ <”
Scroll and select “IPv6 Settings”see Page 9-20
Scroll and select “IPv6”, if not allready set to OFF
Scroll and select “RA (Statless)”, if not allready set to OFF
Scroll and select “DHCP”, if not allready set to OFF
Leave this level “ <”
Scroll and select “Bonjour”, if not allready set to OFF
Scroll and select “Protocol Detail”see Page 9-21
Scroll and select “NetBEUI”, if not allready set to OFF
Scroll and select “SNMP”, if not allready set to ON
Scroll and select “SNMPv3”, if not allready set to OFF
Scroll and select “RAW Port”, if not allready set to ON
Scroll and select “WSD Scan”, if not allready set to OFF see Page 9-22
Scroll and select “WSD Print”, if not allready set to OFF
Scroll and select “Enhanced WSD”, if not allready set to OFF
Scroll and select “Enhanced WSD (SSL)”, if not allready set to OFF
Leave this level “ <”
Leave this level “ <”
Leave this level “ <”
Scroll and select Date/Time/Energy Saver see Page 9-27
Scroll and select “Low Power Timer”, if not allready set to 15 Min
Scroll and select “Sleep Level”, if not allready set to Quick Recovery
Scroll and select “Sleep Rules” if this point exists; if not skip
Scroll and select “Network”, if not allready set to OFF
Scroll and select “FAX”, if not allready set to OFF
Leave this level “ <”
Scroll and select “Sleep Timer”, if not allready set to 15 Min
Leave this level “ <”

Projekt CAMPUS dB
Technical Documentation
Kyocera ECOSYS M6026/M6526cidn
FRA AI/M-D
Author(s): Dirk Czichon
File: CdBTD_Kyocera_EcoSys-M6026M6526cidn.doc
Signed off by:
Manuel Siefker
Version: 1.0
Page 6 of 6
Valid from: 05.07.2014
Vorlage 14.07.2004
2.4 Restart the printer
Scroll and select “Restart”
Press “Yes”
2.5 Handover to ServiceDesk or RolloutControlCenter
Call the ServiceDesk or RolloutControlCenter and handover for testing the reachablitlity of
the printer and final configuration.
Please don’t leave the site before they stated that the printers webconfigpage is reachable.