Kyocera FS-2100DN Programming manual

Using a Web Browser to Manage the IB-51
This section describes how to manage the IB-51 using a web browser.
1. IB-51's Web Page Overview
2.Status Page
3.General Settings Page
4.Advanced Page
5.Troubleshooting
1. IB-51's Web Page Overview
Configure and monitor the IB-51 from the unit's internal webpage, through the IB-51's Web page. The IB-51's Web page is your web
interface for managing the IB-51 from your computer. The computer and IB-51 are linked via TCP/IP.
Note:
Confirm the following points before accessing the IB-51's Web page.
—Your computer must support TCP/IP.
—The IB-51's IP address must be configured.
1-1. Compatible Systems
The IB-51's Web page can be used with these operating systems.
—Windows 2000 (32bit)
—Windows XP (32bit/64bit)
—Windows Vista (32bit/64bit)
—Windows 7 (32bit/64bit)
—Windows Server 2003 (32bit/64bit)
—Windows Server 2008 (32bit/64bit)
—Apple Macintosh OS X 10.x
1-2. Compatible Web Browsers
The following web browsers have been verified for the IB-51's Web page.
1-3. Accessing IB-51's Web page
1. Launch a web browser.
2. In the address bar, enter the IP address assigned to the IB-51 as the URL. The home page gives basic information about the IB-
51 and shows the current status and control panel display.
3. Login to the IB-51's Web page by entering the user name and password.
OS Web Browser
Windows Microsoft Internet Explorer 6.0 or newer
Mozilla Firefox1.5 or newer
Chrome 1.0 or newer
Safari 2 or newer
Mac OS Safari 2 or newer
Page 1 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

4. To view or configure settings, choose a category from the navigation bar on the left.
2. Status Page
You can do the following from the Status Page.
—Change the display language of the IB-51's Web page
—Check the IB-51 network settings
—Check the IB-51's Wireless Settings
—Display the Web page of the printer/MFP that has the IB-51 attached
2-1. Home Page
Figure 1. IB-51's Web page Status Page
This is the first screen displayed after the IB-51's Web page is launched. You can check the status of the IB-51 from this page.
—If "Network Authentication" is disabled on the printer/MFP, the default user name and password are "
A
dmi
n
".
—If "Network Authentication" is enabled on the printer/MFP, the user name and password to be entered will change
depending on the configuration of Windows Server or printer/MFP.
For details, refer to the operation manual of the printer/MFP.
—Enclose the IPv6 address with "[ ]" before you enter it to the address bar of the Web browser.
Example: http://[FE80:0:0:0:2C0:EEFF:FE11:2233]/
Item Description
Language Displayed for multilingual versions of the IB-51's Web page. Choose the desired language from the
drop down list.
Page 2 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

Note:
If the IB-51's Web page display language does not match the display language of the operation panel, some characters may not be
displayed correctly.
2-2. Status Page < Network Status
On the Status page, you can check the settings for a range of operations executed using the control panel or IB-51's Web page, such
as printing and network settings.
2-3 Status Pages > Wireless LAN Status
On this Status Page, you can check the wireless settings currently used by the IB-51.
2-4 CCRX > Printer/MFP
You can display the Web page of the printer/MFP that has the IB-51 attached.
Page Description
Status Pages > Network Status
> General For checking TCP/IP, IPv4, IPv6, AppleTalk, NetBEUI/NetBIOS, Protocol Settings, and LDAP settings.
For TCP/IP, IPv4 and IPv6 details, refer to 4-1. Protocols > TCP/IP > TCP/IP.
For AppleTalk details, refer to 4-9. Protocols > AppleTalk.
For NetBEUI/NetBIOS details, refer to 4-10. Protocols > NetBEUI/NetBIOS.
For Protocol Settings details, refer to 4-5. Protocols > Protocols > Server Settings or 4-6.
Protocols > Protocols > Client Settings.
For LDAP details, refer to 4-17. Management/E-mail > LDAP.
Status Pages > Network Status
> IP Filters For checking the range of IP address that can access the IB-51. If no IP address is specified, all addresses have access rights to the IB-51.
For details, refer to 4-2. Protocols > TCP/IP > IP Filters (IPv4) or 4-3. Protocols > TCP/IP > IP
Filters (IPv6).
Status Pages > Network Status
> SNMP For checking the SNMP settings. For details, refer to 4-15. Management/E-mail > SNMP > General.
Status Pages > Network Status
> POP3/SMTP For checking e-mail-related settings. For details, refer to 4-11. Management/E-mail > SMTP > General or 4-13. Management/E-mail >
POP3 > General.
Status Pages > Network Status
> Logical Printers For checking the logical printer settings. For details, refer to 4-4. Protocols > TCP/IP > Logical Printers.
Status Pages > Network Status
> NetWare For checking the NetWare page settings and status. For details, refer to 4-7. Protocols > NetWare > General.
Status Pages > Network Status
> Security For checking the security settings. For details, refer to 4-20. Security > Encryption > General or 4-5. Protocols > Protocols >
Server Settings.
Item Description
Wireless LAN Status Displays the current wireless status.
Current SSID Displays the SSID configured for the IB-51.
BSSID Displays the BSSID of the access point that the IB-51 is communicating with.
Current Channel Displays the channel configured in the IB-51.
Transfer Rate Displays the transmission rate.
If the printer/MFP does not support this feature, it is not displayed in the navigation bar.
Page 3 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

3. General Settings Page
From this page, you can configure settings applicable to all aspects of IB-51 operation, such as Security and Network settings. You can
restrict access to this page by setting an administrator password. Refer to 3-4. General Settings > Password for details.
Figure 2. IB-51's Web Page General Settings Page
3-1. General Settings > General
From this page, the general settings can be configured.
3-2 General Settings > Wireless LAN > Wireless LAN
From this page, the IB-51's wireless settings can be configured.
Item Description
Push Switch Enables (On) or disables (Off) the function of Push Switch.
Allow firmware updates via the
update utility (IBVERUP) Enables (On) or disables (Off) updates using IBVERUP. Refer to the firmware update for details on the update utility (IBVERUP).
Item Description
Page 4 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

Auto Wireless Setup Feature PIN-Code Clicking "Auto Generate" will generate the IB-51's PIN code.
Wireless LAN Basic
Configuration Wireless Mode Select from below the method of connection to the IB-51's wireless network.
—Infrastructure
—AdHoc
SSID Set the SSID of the wireless LAN to connect the IB-51.
Wireless Authentication Configure the authentication method used when connecting to
the wireless LAN router (access point).
—Open
—Shard
—WPA
—WPA2
—WPA Enterprise
—WPA2 Enterprise
Channel Set the channel used by wireless LAN.
WEP Configuration WEP Enable (On) or disable (Off) the WEP encryption feature.
WEP Key Set the encryption key (WEP key) used for WEP encryption.
WPA/WPA2 Configuration Encryption Mode Select from below the wireless encryption method to use.
When WPA2/WPA2 Enterprise is set as the wireless
authentication method, this is fixed at AES.
—TKIP
—AES
—AUTO
Pre-Shared Key Only when WPA/WPA2 is selected, enter the shared key.
When WPA Enterprise/WPA2 Enterprise is selected, this cannot
be set.
Authentication Protocol Select from below the authentication protocol.
—PEAP
—EAP-TLS
—EAP-TTLS
—EAP-FAST
EAP User Name Enter the EAP user name.
EAP Password Only when EAP-TTLS/PEAP/EAP-FAST is selected, enter the
EAP password.
Internal Authentication Method Only when EAP-TTLS/PEAP is selected, specify from the
following protocols.
When set to PEAP, this is fixed at MSCHAPv2.
—PAP
—CHAP
—MSCHAP
—MSCHAPv2
Server Authentication Enables (On) or disables (Off) the server authentication, when
EAP-TLS/EAP-TTLS/PEAP is selected for the authentication.
Import CA Certificate Imports the CA certificate when EAP-TLS/EAP-TTLS/PEAP is
selected for the authentication.
Import Client Certificate Imports the client certificate, when EAP-TLS is selected for the
authentication.
Automatic PAC File
Distribution Enables (On) or disables (Off) the automatic configuration of the PAC file, when EAP-FAST is selected for the authentication.
Page 5 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

3-3 General Settings > Wireless LAN > Certificate
From this page, the details of the certificates of wireless LAN settings can be checked.
3-4. General Settings > Password
By setting an administrator password, the access to IB-51's Web page can be restricted (excluding the Status Page).
Note:
—The default password is "Admin". We recommend setting an administrator password to prevent unauthorized changes to the IB-
51 settings.
—The password can be up to 15 characters long.
—Make a note of the password in case you forget.
Follow these steps to set up or change the password.
1. Enter the desired password in the new password field.
2. Re-enter the same password in the confirmation field.
3. Click Submit at the bottom of the page.
3-5. General Settings > Time Settings
The IB-51 obtains the current time from a time server on the network. The time is used in various reports sent from the IB-51 via e-mail.
Import PAC Select and import the PAC file, when EAP-FAST is selected for
the authentication, and automatic PAC file is disabled (Off).
Password Enter the password when importing certificates.
32 characters maximum.
Item Description
Client Certification Part of the client certificate can be referenced.
CA Certification Part of the CA certificate can be referenced.
PAC Part of the PAC file can be referenced.
Item Description
New Password Enter the new password.
Confirm New Password Enter the new password again for confirmation.
Item Description
Current Local Time Shows the time as obtained from the time server.
Time Zone For designating the offset from UTC.
Time Protocol For designating the server to obtain for the time. The available servers are as follows.
—None: Do not obtain the time from a server.
—NetWare: Obtain the time from a NetWare server.
Page 6 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

3-6. General Settings > Reset
To enable the changes you have made to IB-51 network settings, you must restart the network interface. You can also restore the
default settings as needed.
4. Advanced Page
This page includes advanced settings applicable to all aspects of IB-51 operation. You can restrict access to this page by setting an
administrator password. Refer to 3-4. General Settings > Password for details.
Figure 3. IB-51's Web Page Advanced Page
4-1. Protocols > TCP/IP > TCP/IP
This table gives an overview of the items displayed on this page.
—SNTP Server: Obtain the time from a SNTP server. Designate the server name or IP
address.
SNTP Server Set the SNTP server name or IP address.
Item Description
Restart Network Interface Click the Restart button to restart the network interface.
Set all Network Settings to
Factory Default Click the Reset button to restore the default network interface settings.
Page 7 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

4-2. Protocols > TCP/IP > IP Filters (IPv4)
IP Filters(IPv4) can be used to specify the host or network that can use IB-51. Up to 10 access list entries can be specified.
Item Description
General Settings Host Name For designating the name of IB-51.
IPv4 Settings DHCP Enable (On) or disable (Off) the auto IP address configuration
using DHCP.
Auto-IP Enable (On) or disable (Off) the IP address assignment using
Auto-IP.
IP Address For assigning the IB-51's IP address. Example: 192.168.110.171
Subnet Mask For designating the subnet mask.
Default Gateway For designating the IP address of the default gateway.
Domain Name For designating the DNS name of the domain to which the IB-51
belongs. Do not designate the host name.
DNS Server (Primary,
Secondary) For designating the primary and secondary IP addresses of the DNS (Domain Name System) server. To obtain an IP address
from the DHCP server, Use DNS Server from DHCP must be
selected.
WINS Server (Primary,
Secondary) For designating the primary and secondary IP addresses of the WINS server. To obtain an IP address from the DHCP server,
Use WINS Server from DHCP must be selected.
Scope ID For determining the scope of IP addresses the Windows server
can assign or lease.
Bonjour Bonjour can be switched on and off. Activate Bonjour if you want
to be able to add printers/MFPs through Print Center in Mac OS
X. Printers/MFPs must support KPDL for printing.
Bonjour Name For designating a name to be used with Bonjour.
IPv6 Settings IPv6 Switches IPv6 on and off. When this setting is on, the IB-51
supports IPv6. In order to use IPv6, however, all of the devices
on a network need to support IPv6.
IP Address Assign the IPv6 address to IB-51.
Prefix Length Specifies the prefix length for IPv6.
RA (Stateless) Enable (On) or disable (Off) the IPv6 address assignment using
RA.
Default Gateway For designating the IP address of the default gateway.
DHCPv6 (Stateful) Enable (On) or disable (Off) the auto IP address configuration
using DHCPv6.
Domain Name For designating the DNS name of the domain to which the IB-51
belongs. Do not designate the host name.
DNS Server (Primary,
Secondary) For designating the primary and secondary IP addresses of the DNS (Domain Name System) server. To obtain an IP address
from the DHCP server, Use DNS Server from DHCP must be
selected.
Item Description
IP Address Specify the IP address or work address to allow access from.
Page 8 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

4-3. Protocols > TCP/IP > IP Filters (IPv6)
IP Filters(IPv6) can be used to specify the host or network that can use IB-51. Up to 10 access list entries can be specified.
4-4. Protocols > TCP/IP > Logical Printers
The IB-51 can be used as a virtual printer that adds or replaces strings (commands) at the start or end of job data. You can configure
up to eight logical printers.
Logical printers use FTP, LPR, or IPP as the communication protocol. Printouts to nonexistent ports are all sent to Logical Printer 1.
Subnet Mask Specify the subnet mask to allow access from. To allow access from all hosts over the network
192, enter "192.0.0.0" for IP address and "255.0.0.0" for subnet mask. It is possible to leave this
field blank.
Protocols Select the protocols that will be allowed to access from the following choices.
—LPD
—FTP
—IPP
—HTTP
—RAW Port
—SNMP
—HTTPS(IPPS)
—ThinPrint
Item Description
IP Address (IPv6) Specify the IP address to allow access from.
Prefix Length Specify the prefix length for IPv6 (0-128 decimal characters).
Protocols Select the protocols that will be allowed to access from the following choices.
—LPD
—FTP
—IPP
—HTTP
—RAW Port
—SNMP
—HTTPS(IPPS)
Item Description
TCP/IP Port Number You can designate the port number for logical printers just as you can designate the physical port
number for TCP (such as 9100). Data sent to the designated physical port is converted in a way
corresponding to the designated logical printer. If you designate the same port number as a port
that was previously designated (such as for FTP or LPD), the port designation is invalid.
Bi-directional Printing You can enable (On) or disable (OFF) bi-directional printing that uses the physical port for TCP/IP
communication. If this setting is off, all data received from the printer is disregarded. When printing
with PostScript, PJL, or other commands, bi-directional printing must be on to return data to the
client that was received from the printer.
Start of Job String You can designate a string to be sent to the printer before direct output to the output port (lp port).
If you need to send a control code before printing, designate that string.
End of Job String You can designate a string to be sent to the printer after direct output to the output port (lp port). If
you need to send a control code after printing, designate that string.
Banner Page Banner page printing can be enabled (On) or disabled (Off) when printing via FTP or LPD.
Filter Setting Select ASCII to KPDL to enable the filter setting.
Page 9 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...

4-5. Protocols > Protocols > Server Settings
The protocols to use can be selected.
4-6. Protocols > Protocols > Client Settings
The FTP client and CIFS client can be configured.
Item Description
Server Settings Enable (On) or disable (Off) the following protocols.
—IPP
—IPP over SSL*
—LPD
—RAW Port
—HTTP
—HTTPS*
*Note : To activate the configuration, the Encryption needs to be
set to ON
.
FTP Server FTP Server Enables (On) or disables (Off) the FTP server.
FTP Server Port Number Sets the FTP Port Number. (Default port: 21)
FTP Status Check Enables (On) or disables (Off) the FTP status check.
FTP Server over SSL Encrypts using SSL. Select "OFF" to not use it.
—OFF
—StartTLS
—FTP Server over SSL
—To activate the configuration, the Encryption needs
to be set to ON.
ThinPrint ThinPrint Enables (On) or disables (Off) ThinPrint. ThinPrint is a
technology that distributes the network load due to printing
through compression and bandwidth control of the print data. To
use ThinPrint, .printServerEngine is required on the server,
and .printClient is required on the client ( printer/MFP ). When
the ThinPrint feature of the IB-51 is turned on, the IB-51
operates as a ThinPrint client.
ThinPrint Port Number Specifies the port that is used for communication
with .printServerEngine. The default value is 4000.
ThinPrint over SSL Select to enable (On) or disable (Off) encryption by SSL.
—To activate the configuration, the Encryption needs
to be set to ON.
Import Client Certificate Imports the client certificate, when EAP-TLS is selected for the
authentication.
Password Enter the password when importing certificates.
32 characters maximum.
Import CA Certificate Imports the CA certificate when EAP-TLS/EAP-TTLS/PEAP is
selected for the authentication.
Page 10 of 2
2
Using a Web Browser to Manage the I
B
-51
10
/
2
/
201
2
file:///C:/Tom/PDF/I
B
-51/I
B
-51%20Setu
p
%20Guide%20HTML%20En
g
lish/card
_
home
pa
...