La Crosse Technology 308-1409BT User manual

Model:308-1409BT/308-1409WT
Instruction Manual
DC: 061716
Wireless Temperature Station
Get Started
1. Insert 2 AA batteries into the TX141-Bv2 sensor. Check polarity.
LED
AA
AA
2. Insert 2 AAA batteries into the station. Check polarity.
3. Allow sensor and station to remain 5-10 feet apart for 5 minutes
to lock in the sensor signal.
4. Set time.
5. After 5 minutes place sensor outside in a shaded location.
AAA
AAA
http://bit.ly/LaxTechTalk
For online video support:

Fahrenheit/Celsius
• Press and release the +/°F/°C button to switch between
Celsius or Fahrenheit temperature display.
HI/LO Temperature Readings
• Press SET/HI/LO button to view the LO records.
• Hold the SET/HI/LO button for 2 seconds to manually clear the LO
records in memory.
• Press SET/HI/LO button again, to view the HI records.
• Hold the SET/HI/LO button for 2 seconds to manually clear the HI
records in memory.
• The records will automatically reset at 12:00AM.
Page | 1 www.lacrossetechnology.com/support 308-1409BT/308-1409WT
LO Temps HI Temps
Set Time
1. Press and hold the SET button for 2 seconds to enter setting mode.
12H will ash, press +/°F/°C to select. Press SET to conrm.
2. Hour will ash, press+/°F/°C to set. Press SET to conrm.
3. Minutes will ash, press +/°F/°C to set. Press SET to conrm.
Temperature Trend Arrows
The temperature (2°F / 1°C) trend indicators update every 15
minutes or less .
• Temperature has risen ^
• Temperature has not changed >
• Temperature has fallen
^
Time Format Hour Minutes

Low Battery Icons
• Battery icon near outdoor temperature, change batteries in the outdoor sensor.
• Battery icon near indoor temperature, change batteries in the temperature station.
Specications
Indoor Temp Range: 32°F to 122°F (0°C to 50°C)
Outdoor Temp Range: -40°F to 140°F (-40°C to 60°C)
Distance: Over 300 ft. (91 meters) RF 433MHz (open air)
Power Station: 2-AAA, IEC, LR3 batteries (not included)
Power TX141-Bv2: 2-AA, IEC, LR6 batteries (not included)
Battery Life Station: over 12 months with reputable batteries
Battery life TX141-Bv2: over 24 months with reputable batteries
Dimensions Station: 2.64” W x 1.38” D x 3.66” H (66 W x 35 D x 93 H mm)
Dimensions TX141-Bv2: 1.57”W x 0.82” D x 5.11” H (40 W x 20.8 D x 129.8mm H)
• Mount the Outdoor Sensor on a north-facing wall or in any well shaded area. Under an
eave or deck rail is preferred.
• The maximum wireless transmission range to the station is over 300 feet (91 meters)
in open air, not including walls or oors.
• Be sure the outdoor sensor is mounted vertically.
Position Outdoor Sensor
Warranty and Support
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of
purchase) on this product relating to manufacturing defects in materials & workmanship.
Before returning a product, please contact our friendly customer support with questions or
visit our online help:
Phone: [phone]
Online Product Support:
www.lacrossetechnology.com/support
Product Registration:
www.lacrossetechnology.com/support/register
View full warranty details online at:
www.lacrossetechnology.com/warranty_info.pdf
Warranty Address:
La Crosse Technology, Ltd
2830 S. 26th St.
La Crosse, WI 54601
Protected under U.S. Patents: 5,978,738 | 6,076,044 | RE43903
308-1409BT/308-1409WT www.lacrossetechnology.com/support Page | 2
Outdoor Sensor Search
• Hold +/°F/°C for 3 seconds to search for the outdoor sensor.
• If the signal is lost, station will display the LAST DATA recorded for 10 minutes, after
that 10 minutes, the station will display dashes “--”.
• After 30 minutes, station starts looking for the sensor automatically.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized changes
or modications to this equipment. Such changes or modications could void the user authority to
operate the equipment.
All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or
processed using electronic, mechanical or chemical process without the written permission of the
publisher.
This booklet may contain errors or misprints. The information it contains is regularly checked and
corrections are included in subsequent editions. We disclaim any responsibility for any technical error
or printing error, or their consequences.
All trademarks and patents are recognized.
Canada Statement
This device complies with CNR Industry Canada license -exempt devices. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
FCC Statement
• Do not mix old and new batteries
• Do not mix Alkaline, Standard, Lithium or Rechargeable Batteries
• Always purchase the correct size and grade of battery most suitable for intended use.
• Replace all batteries of a set at the same time.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries are installed with correct polarity (+ and -).
• Remove batteries from equipment which is not to be used for an extended period
• Remove expired batteries promptly.
Care and Maintenance
Page | 3 www.lacrossetechnology.com/support 308-1409BT/308-1409WT
Visit Us on Social Media
http://bit.ly/LaxTech_Facebook
http://bit.ly/LaxTech__Twitter
http://bit.ly/LaxTech_YouTube
http://bit.ly/LaxTech_Pinterest
For personalized interaction
Join the conversation
Latest video content
Pin and share