La Crosse Technology WS-7136U User manual

WS-7136U
Wireless 433 MHz
Temperature Station
Instruction Manual

2
TABLE OF CONTENTS
Topic Page
Inventory of Contents 3
Additional Equipment 4
Quick Setup 5-9
Detailed Setup Guide
Battery Installation 10-12
Setting the Time Format 13
Setting the Temp. Format 13-14
Setting the Time 14-15
Features
Minimum and Maximum
Temperatures
16-17
Resetting Minimum and
Maximum Temperatures
17
Adding additional remote
temperature sensors (optional)
17-19
Viewing and operating multiple
remote temperature sensors
20
Mounting 21-22
Troubleshooting 23-26
Maintenance and Care 26
Specifications 27-28
Warranty Information 28-31

INVENTORY OF CONTENTS
1. The indoor
temperature
station (Figure 1)
2. The remote
temperature
sensor (TX6U)
and mounting
bracket. (Figure 2)
3. Mounting
hardware.
4. Instruction
Manual and
Warranty Card.
3
Figure 1
Figure 2

4
ADDITIONAL EQUIPMENT
(not included)
1. 1 Philips screwdriver.
2. 2 Fresh AAA 1.5V batteries.
(for the indoor temperature station)
3. 2 Fresh AA 1.5V batteries.
(for the temperature sensor)

5
QUICK SETUP
Hint: Use good quality Alkaline Batteries
and avoid rechargeable batteries.
1. Have the indoor temperature station and
remote temperature sensor 3 to 5 feet
apart.
2. Batteries should be out of all units for
10 minutes.
3. Place the batteries into the remote
temperature sensor first, then into the
indoor temperature station.
(All remote temperature sensors must
be started before the indoor weather
stations)
4. DO NOT PRESS ANY BUTTONS
FOR 15 MINUTES.

6
In this time the indoor temperature station
and remote temperature sensor will start to
talk to each other and the display will show
both the indoor temperature and an outdoor
temperature. If the indoor temperature
station does not display both the indoor
temperature and the outdoor temperature
after the 15 minutes please retry the set up as
shown on page five.
After both the indoor temperature and
outdoor temperature are displayed for 15
minutes you can place your remote
temperature sensor outdoors and set your
time.

7
Notes on Outdoor Sensor Placement
The remote temperature sensor should be
placed in a dry, shaded area. Fog and mist
will not harm your remote temp/humidity
sensor but direct rain must be avoided.
The remote temperature sensor has a range
of 80 feet. Any walls that the signal will
have to pass through will reduce distance.
An outdoor wall or window can have up to
30 feet of resistance and an interior wall can
have up to 20 feet of resistance. Your
distance plus resistance should not exceed 80
ft. in a straight line.

8
To complete the set up of your indoor
temperature station after the 15 minutes have
passed, please follow the steps below.
1. Press and hold the “SET” button for 5
seconds.
Note: A “12h” or “24h” will appear on
the top line. (“12h” for AM/PM, “24h”
for military time)
a. To change between “12h” and
“24h” press and release the
“RESET/+” button.
b. When you have your choice
shown on the display press
and release the “SET” button
once.
2. Degree Fahrenheit will now show.
a. To change between
Fahrenheit and Celsius, press
and release the “RESET/+”
button.
b. When you have your choice
shown on the display press

9
and release the “SET” button
once.
3. An hour will now be flashing.
a. Press and release the
“RESET/+” button until the
correct hour is shown.
Note: When in the 12h mode
“PM” is displayed in the upper left
corner of the display between noon
and midnight. During the AM
hours this area will be blank.
b. When the correct hour is
shown, press and release the
“SET” button once.
4. A minute will now be flashing.
a. Press and release the
“RESET/+” button until the
correct minutes are displayed.
Press and release the SET button once
more and you are done.

DETAILED SETUP GUIDE
I. BATTERY INSTALLATION
A. REMOTE TEMPERATURE
SENSOR
Battery
compartment
1. Remove the mounting bracket.
Battery cover
2. Remove battery cover.
3. Observing the correct polarity, install
2 AA batteries—make sure they do not
spring free, or start-up problems may
occur.
4. Replace cover.
10