La Crosse Technology WS7034UITCA User manual

WS7034UITCA
915 MHz WIRELESS TEMPERATURE STATION
STATION DE TEMPERATURE SANS FIL 915 MHz
Instru tion manual
Manuel d'lnstru tions

Contents
Language Page
______________________________________________________________________
English 1
French 27

1
TABLE OF CONTENTS
Topic Page
Inventory of contents 4
Quick Setup 5
Detailed setup guide 6
Battery Installation 6
°C/° Temperature unit setting 11
Manual Time setting 11
eatures 13
Min and Max Temperature 13
Resetting Min & Max Temperature 13
Adding additional Temperature Sensors 14
Viewing & Operating with Multiple Sensors 16
Mounting 16
Maintenance and care 22

2
Specification 22
Warranty Information 24
This product offers:
INSTANT TRAN
SMISSION
is the state
-
of
-
the
-
art
new wire ess transmission techno ogy,
exc usive y designed and deve oped by LA
CROSSE TECHNOLOGY. INSTANT
TRANSMISSION
offers you an immediate update
(every 4 seconds!) of a your outdoor data
measured from the transmitters: fo ow your
c imatic variations in rea -time!

3
FIGURE 1
12 Hour Time
Display
Set/Channel
Button
Minimum/Maximum
& Plus Button
Sensor signal
reception icon
Indoor
Temperature
(° or °C)
Out
door
Temperature
(° or °C)

4
Figure 2
INVENTORY OF CONTENTS
1. Wireless Temperature Station ( igure 1)
2. Wireless Temperature Sensor (TX29U-IT) and mounting bracket. ( igure 2)
3. Instruction Manual and Warranty Card.

5
QUICK SETUP
Hint: Use good qua ity A ka ine Batteries; avoid rechargeab e batteries.
1. Have the Wireless Temperature Station and temperature sensor 3 to 5 feet apart.
2. Batteries should be out of both units for 5 minutes.
3. Place the batteries into the Temperature sensor first and next into the Wireless Temperature
Station.
4. DO NOT PRESS ANY BUTTONS OR 5 MINUTES.
In this time the Wireless Temperature Station and the temperature sensor will begin to communicate with
each other, and the display will show both the indoor temperature and an outdoor temperature. If the
Wireless Temperature Station does not display both temperatures after the 5 minutes, please retry the set
up as stated above. After both indoor and outdoor temperatures are displayed for 5 minutes you can
place your temperature sensor outdoors, and set your time.
The temperature sensor should be placed in a dry, shaded area (ex: under the eve of a roof). The
temperature sensor has a range of 330 feet. Any walls that the signal will have to pass through will
reduce distance. An outdoor wall or window will have up to 20 feet of resistance and an interior wall will

6
have up to 10 feet of resistance. Your distance plus resistance should not exceed 330 feet in a straight
line.
NOTE: og and mist will not harm your temperature sensor, but direct rain must be avoided.
DETAILED SETUP GUIDE
BATTERY INSTALLATION - When one Temperature sensor is being used
1. irst, insert the batteries to the Temperature sensor (see “Temperature sensor” below).
2. Within 2 minutes of powering up the sensor, insert the batteries to the Temperature Station (see
“Wire ess Temperature station” below). Once the batteries are in place, all segments of the LCD
will light up briefly. ollowing the indoor temperature and the time as 12:00 will be displayed. If they
are not shown in LCD after 60 seconds, remove the batteries and wait for at least 60 seconds
before reinserting them. Once the indoor data is displayed user may proceed to the next step.
3. After the batteries are inserted, the Temperature Station will start receiving data signal from the
sensor. The outdoor temperature should then be displayed on the Temperature Station. If this
does not happen after 2 minutes, the batteries will need to be removed from both units and reset
from step 1 and the signal reception icon is no longer shown.

7
TEMPERATURE SENSOR
The Temperature sensor uses 2 x AA, IEC LR6, 1.5V batteries. To install and replace the batteries,
please follow the steps below:
1. Remove the cover at the back of the sensor.
2. Insert batteries observing the correct polarity (see marking).
3. Replace compartment cover.

8
WIRELESS TEMPERATURE STATION
The Temperature station uses 2 x AAA, IEC LR3, 1.5V batteries. To install and replace the batteries,
please follow the steps below:
1. Remove the Battery Cover on the back of the Wireless
Temperature Station.
2. Observing the correct polarity, install batteries.
3. Replace Battery Cover.
Battery
compartment
Battery cover