La Toulousaine 7386 User manual

09/21
(Document reserved for installers)
This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.2
- Hammer drill
- Set of steel/concrete drill bits
- Electric screwdriver with end-pieces
- Allen keys + Flat wrenches
- Flat screwdriver 2,5 mm
- Wire stripper pliers
- Hammer/Chisel
- Spirit level
- Plumb bob
- Hacksaw
- Angle grinder
- Riveting pliers
- Tape measure
- Appropriate screws and
pins for the supports
- 10 mm shims
Required equipment........................................................................................................p.2
Installation instructions....................................................................................................p.3
Electrical duct installation................................................................................................p.4
Assembling + installing the aluminum posts (Option)......................................................p.4
Check of existing posts .........................................................................................p.5 to p.6
Guide rail attachment (on all types of posts)...................................................................p.6
Totem operator installation (on all types of posts).................................................p.7 to p.8
Installing the gate (on all types of posts)...............................................................p.8 to p.9
Finishing clips ...............................................................................................................p.10
Installing the opening stop ............................................................................................p.10
Installing the closing stop (on aluminum posts).............................................................p.11
Installing the closing stop (on existing posts)................................................................p.11
Receiver box adjustment...............................................................................................p.11
Setting the limit-switches...............................................................................................p.12
Connection plan ............................................................................................................p.13
DIPS switch factory settings..........................................................................................p.13
IMPORTANT : Flashing amber light and cells installation ............................................p.14
Outdoor antenna installation .........................................................................................p.15
Self-learning..................................................................................................................p.16
In case of a fault or before the self-learning cycle : Reset board .................................p.17
Radio receiver :
- Transmitter programming ..........................................................................................p.17
- Wireless keypad programming..................................................................................p.18
- Deleting a key from the transmitter............................................................................p.19
- Deleting a channel.....................................................................................................p.19
- Memory wipe.............................................................................................................p.19
Options :
- Connection : Pulse button .........................................................................................p.20
- Connection : Partial open button ...............................................................................p.20
- Connection : External antenna ..................................................................................p.20
- Connection : Battery..................................................................................................p.21
Breakdown assistance ..................................................................................................p.22
Description of LED flashing sequences.........................................................................p.22
Appendix ............................................................................................................ p.23 à p.24
In the case of an openwork gate ...................................................................................p.25

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.3
* Before beginning the assembly, read this manual carefully.
* This fence element must be installed by a professional technician.
* All the parts delivered are specifically sized for this product.
Adding and/or using other parts may be detrimental to safety and may affect
the product’s warranty.
* Any modification or improvement of this fence element must be compliant
with the standard EN 13241 + A2.
In this case, a "modification/transformation" file must be created by the installer
as per the standard EN 12635 annex C.
* Use the appropriate tools to install these products.
Ensure that the work is carried out on a stable floor.
* Ensure that the assembly area is clear, clean and clearly marked out.
* Ensure that no other people are present at the assembly site apart from the installers.
Non-authorized persons (children for example !) who are present at the site risk injury
during assembly.
*All the components of this fence element must be installed in compliance with the
installation instructions provided in this manual.
* All requirements of EN 13241 + A2 must be met and checked if necessary.
WARNING !
To ensure that this product is assembled,
used and maintained in complete safety, it is important
to follow the instructions provided in this document.
For everyone’s safety,
observe the following precautionary measures.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.4
Interior view
Operator power supply 230V 3x2,5 mm²
Totem operator
136 mm
Power output
136 mm
Operator positioning,
if opening to the left
Operator positioning,
if opening to the right
Clip
Remove clips
before the profiles are assembled
12
Assemble the profiles Assembled posts
3
243 mm
115 mm
243 mm
115 mm Power output
Totem operator
Profiles

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.5
Fill completely
Iron + Concrete framework
Overall height*
400 mm
400 mm
* Overall width and
height correspond to
the order dimensions.
Fill completely
Once the installation is complete, cut the attachment clips according to the height of the posts,
then click them onto the posts.
Please note :
Before installing the gate,
check that the concrete/post
is completely set
(21 days to dry on average).
Do not attach
the caps
It is essential to check
the plumb line of the posts
on all sides.
The 2 posts must be
at the same level
and correctly aligned.
Height Height
Width
Width
Check under hat :
Width between posts and height of posts
Checking worksite dimensions

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.6
Please note :
Ensure that the threshold is leveled correctly ;
If you feel the threshold is too irregular or
sloping, do it again.
Level line
Post at bottom of slope
Street
view
Straight post
Rail
50 mm
Street
view
Outward leaning post
Rail
50 mm
Street
view
Inward leaning post
Rail
50 mm
Closing post
Opening side
Attach the rail from the closing post ; Using the 8 mm pins and suitable screws (not supplied).
Opening post
Rail assembly
Junction pin

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.7
136 mm 136 mm
If left opening If right opening
+
+
Interior view
Fittings adapted to the support
Pins + Screws (not provided) Ø10 mm
Floor fittings
Trace the position of the anti
-vibration bearing plate then
remove the Totem operator
+
2
1
Permanently fix the Totem
operator on the ground
on the 3 fixing points
3
Remove the cap
Drill tracings
on the post
Anti-vibration plate attachment
Please note : Attach the Totem operator to a single point, so that it can be removed more easily later.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.8
Mount the cap and secure
it with the set screws
6
Attach the anti-vibration bearing
plate to the post
5
Ensure the Totem operator is plumb and fix
the adjustment screws of the bearing plate
4
Top view
Attach wheel covers
Wide head rivets
4,8x16 (provided)

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.9
Place the gate
- Gate open, press the rack and pinion on the sprocket so that the notches of the rack and pinion
coincide with the notches of the sprocket and lock the screw.
- Unwind the gate as you go until it closes and repeat the above step until all the rack and pinion
screws are tightened.
Sprocket
Rack and pinion
Lock the screw
Adjust the rack
Guiding
rail
- Place the gate on the guiding rail.
- Advance it towards the Totem operator to slide
the bearings into the gate’s transom guide rail.
- Check that the gate is plumb, adjust the guiding
bearings accordingly and lock them in place.
Guiding
bearings
Transom guide rail
Please note : Check that the operator is disengaged (clutch lever in down position).
Please note² : The height of the operator sprocket is preset at the factory.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.10
- Mount the finishing clips on the Totem operator.
- Cut the clip around the guide rollers.
Opening post
Opening stop
- Open gate to opening post.
- Position the opening stop on the floor.
- Attach it with suitable pins or screws (not provided).
Finishing clips
Installing the opening stop