La Toulousaine 9827 User manual

This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
R2-TE-021 rev B
(Installers use only)
INSTALLATION
Point-of-sale advertising
Manual
03/23

2
This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
_N°9827
Installation Point-of-sale advertising
03/23
On Leveled Ground
1. Insert the 2 reinforcements blades into the slats, then screw the 2 bases foot with Ø4,2 mm screws :
2. Counter-drill bores diameter 5,5 mm, the slat and reinforcements (2 holes out of 10 are not reachable) :
Central Post
Screw the post middle of the slat and in the holes formerly drilled. Use 4 screws Ø6,3 mm plus washers.
4 holes
2 holes
Turn the inserts towards
the side of the slat where
the 4 holes are located.

3
This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
_N°9827
Installation Point-of-sale advertising
03/23
Fence Half Post
Opposite side of the inserts, on the non-drilled face,
position the half-post right in the middle
and drill this assembly 5 mm diameter hole.
Then screw the 4 screws Ø5,5 mm.
CREATIV Fence
Follow the steps described into
the manual of installation included into your order.
Bottom and Top Hinges
Assemble the hinges
on the central post.
Then, install the 2 nut covers
on the bottom hinge

4
This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
_N°9827
Installation Point-of-sale advertising
03/23
Second Post
1. Place the second post against the base
(visible bottom holes) and screw with 2 screws
Ø6,3 mm + washers.
2. Unscrew the base and counter drill the slat + reinforcements
5,5 mm diameter.
Then screw the post with the 2 screws Ø6,3 mm + washers.
3. Retighten the base permanently and screw the 2 legs with self-drilling Ø4,2 mm.
Install the 10 nuts covers onto the Ø6,3 mm screw heads.
Turn the holes towards the posts,
holes side of the slat.

5
This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
_N°9827
Installation Point-of-sale advertising
03/23
Gate Stop
On the same post, position the gate stop in
line with the post’s drillings and counter-drill
5 mm holes.
Screw the gate stop with the 3 tapping screws
Ø5,5 mm.
Pedestrian Gate
1. Place the pedestrian gate opened at 90°
onto the bottom hinge axis.
2. Tilt the pedestrian gate towards the post and place the screw into the guide.
Screw until the pedestrian gate is leveled.
3. Lock when leveled tightening
the top hinge.
10 mm
90°
6
13

6
This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
_N°9827
Installation Point-of-sale advertising
03/23
Handle/Lock
Install the handle and the lock.
Nota : The latch can be turned
and is adjustable in depth.
Finishing Profile
1. Slide the finishing profile into the notches of the top and bottom
hinges until it flushes the slat.
2. Lock permanently distorting slightly the finishing profile.
Top Hinge Cover
Screw the top hinge cover using the supplied M6x10 screw.
4
3

7
This document is our exclusive property and may not be copied. It may at any time be modified as the product evolves.
_N°9827
Installation Point-of-sale advertising
03/23
Post Lid
Screw the 2 post lids onto the posts using the Ø4,2 mm screws.