La Toulousaine 1400 User manual

Attaching the key switch and release box :
1 - Unscrew the front of the box, remove the cap
and the watertight seal.
2 - Turn the key approx. 45° to the right or left
and unscrew the approx. 15 mm hexagon screw
with the 5 mm Allen key supplied with the box.
3 - Take off the lid.
4 - Remove the support with the micro-switches
and drill the 2 housing fastening holes.
5 - Drill the 2 cable ducts (Ø12-14) and fix the housing to
the wall with the water evacuation hole downwards.
6 - Reassemble the support with the cabled micro-
switches in the housing, connect the cable to the
earth socket and push the cables neatly into the
housing. (See connection chapter)
7 - Attach the earth cable to the cover and bypass
the micro-switches.
8 - Reassemble the cover by turning the wrench by 45°
to right or left, screw in the hexagon screw with
an Allen key, replace the watertight seal and the
cover and screw the front of the box back on.
- Check the mechanical functions of the key switch
box.
N°1400
This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
1
2
1
1
(Document reserved for installers)
Wall-mounted/built-in
key switch and release box
Attaching the key switch box and cable tensioner
1
Joint
Allen key
Hexagon screw
cable
ducts
2
fastening holes
evacuation hole
Installation manual
Cap
05/18
2

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
Installation_Key switch and release box_N°1400
05/18 p.2
Warning : To remove the key from the cylinder barrel,
align the red line of the hexagon screw facing
the black point on the front of the box.
Setting up the cable tensioner :
1 - Remove the cover of the cable tensioner, drill 2
holes in the wall using the 2 oblong holes Ø5 of the
tensioner.
2 - Run the power cables and fix the tensioner housing
to the wall.
3 - Pass the cable through the hexagonal screw of the
key contactor already cabled and leave the two
washers on the cable.
4 - Connect the electrical cables to the operator.
(See connection chapter)
5 - Insert the cable sheaths into the cable tensioner as far
as they will go.
6 - Pass the operator cable and the cable of the key
switch box in the sheaths.
7 - Tighten both cables with the screws of the cable
clamp.
Warning : The cable clamp must be at the top
of the slide. (operator inlet side)
8 - Tighten the cables on the operator and key switch box
side using the cable tensioners.
9 - Check the operator release with the Allen key and
repeat steps 7 and 8 if necessary.
10 - After checking that the release mechanism works
correctly, shorten the cables protruding from the
cable clamp.
11 - Reassemble the cover on the cable tensioner and
check the electrical and mechanical functioning of
your installation.
Warning : You can use all DIN European profile
cylinder but the bit of the barrel (cylinder)
must obligatorily be in 0° position
(or midday seen from the front).
6
6
6
5
5
3
4
6
4
oblong hole Ø5
oblong hole Ø5
5
tensioning
housing
power
cables
cable
2 washers
6
sheath
sheath
cable
tensioner
cable
tensioner
cable
operator
key switch
box cable
Screw of
the cable
clamp
3
red line
black point
grease
Operator

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
Installation_Key switch and release box_N°1400
05/18 p.3
Connection
Key switch and release box (BCDA/BCDE)
Important :
- The cable sheath must be free (not pinched or wedged).
- The earth wire must be connected to the metal body of the key switch box using a clamp screw.
- Ensure the box is well sealed in relation to the wall support using a flexible sealant.
Please note : For the installation of the release mechanism cable, refer to the manual supplied with the housing.
Phase (red)
Earth (green/yellow)
Descent phase (brown)
Neutral
(blue)
13
14 13
14
Bridging
Wall-mounted/built-in key switch box
and release mechanism (BCDA/BCDE)
Ascent phase (black)
Key switch and release box (BCDA/BCDE)
with button box (BBA1/BBE1)
Important :
- The cable sheath must be free (not pinched or wedged).
- The earth wire must be connected to the metal body of the key switch box using a clamp screw.
- Ensure the box is well sealed in relation to the wall support using a flexible sealant.
Please note : For the installation of the release mechanism cable, refer to the manual supplied with the housing.
Phase (red)
Earth (green/yellow)
Ascent phase
(black)
Neutral
(blue)
13
14 13
14
Wall-mounted/built-in key switch box
and release mechanism (BCA/BCE)
Wall-mounted/built-in button box
(BBA1/BBE1)
Bridging
Operator
Power supply
single-phase 230V
Operator
Power supply
single-phase 230V

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
Installation_Key switch and release box_N°1400
05/18 p.5
1 - Insert the key into the box and turn it by approximately
45° right or left.
2 - Unscrew the approx. 15 mm hexagon screw with the
5 mm Allen key supplied with the box .
3 - Raise or lower the shutter smoothly and slowly to
avoid activating the anti-fall guard.
- If the anti-fall guard is activated during descent :
• Raise the shutter 10 cm
(the anti-fall guard unlocks).
• Then lower the shutter again smoothly
and slowly.
4 - After repair, tighten the hexagon screw completely
with the 5 mm Allen key to engage the operator and
return to motorized operation.
5 - To remove the key from the cylinder, align the red line
of the hexagonal screw with the black dot on the front
of the box. 4
1
1
Instructions for use of shutters equipped
with an anti-fall guard
" LA TOULOUSAINE "
13
2
Emergency operation
Hexagon screw
Allen key
Red line
Black dot
Hexagon
screw
1
2
3
4