LAMBORGHINI MIURA AGORA 2022 User manual

STAGE 07: BUILDING THE
LEFT CYLINDER HEAD
STAGE 08: INSTALLING COVER BOLTS
STAGE 09: BUILDING THE RIGHT CYLINDER
HEAD AND ATTACHING SIDE COVERS
STAGE 10: ASSEMBLING THE RIGHT AIR FILTER
BOX AND FITTING THE DISTRIBUTORS
STAGE 11: LEFT CARBURETTOR 1
STAGE 12: LEFT CARBURETTOR 2
STAGE 13: ATTACHING THE
SPARK PLUG CABLES
STAGE 14: RIGHT CARBURETTOR 1
STAGE 15: RIGHT CARBURETTOR 2
Pack 02
BUILD INSTRUCTIONS
The “Automobili Lamborghini” and “Automobili Lamborghini Bull and Shield” trademarks, copyrights,
designs and models are used under license from Automobile Lamborghini S.p.A, Italy.

AGORAMODELS LAMBORGHINI MIURA
2
Spare screws are included with each part. Occasionally, you may be instructed to keep spare or
unused screws for a later stage. Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
Left and Right! When building your Lamborghini, the left or right hand side refers to each side
as you are sitting in the car.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!

AGORAMODELS LAMBORGHINI MIURA
3
Advice from the experts
Cam shaft cover (left)
Cylinder head (left)
The Lamborghini Miura features a transverse mid-mounted V12 engine, with the crankshaft axis
perpendicular to the direction of travel. Some of the engine parts will be referred to as left and
right in the build instructions, though the engine will be mounted transversely.
The photo below shows the assembled parts which are labelled so that you can refer to it
during your build. The inset photos show the different ends of the left and right cylinder head
to help with differentiating the two.
Cam shaft cover (right)
Cylinder head (right)
Left Right
Distributor (left) Distributor (right)

AGORAMODELS LAMBORGHINI MIURA
4
XXX
Name
Cylinder head (left)
Cam shaft cover (left)
Cam shaft cover (right)
Lamborghini shield emblem
Model tweezers
Cover bolt x20
STAGE 07 PARTS LIST
In this first stage for Pack 02, you’ll
assemble the left cylinder head and
install the covers onto it.
The Lamborghini shield emblem
supplied will not be used in this
pack, so can be stored away safely.
Cylinder head (left)
Stage 07: Building the Left Cylinder Head
Cam shaft cover (right)
Lamborghini shield emblem
Model tweezers
Cover bolt x20
Cam shaft cover (left)

AGORAMODELS LAMBORGHINI MIURA
5
1
3
2
4
Carefully cut sixteen cover bolts from their sprue at the point shown in
the photo.
Take the two cam shaft covers and lay them on your work surface as
shown. There are eight holes (circled) in each cover into which the
bolts will be inserted.
Note: you may need to twist the blade of a sharp modelling knife
around the inside of the holes to remove excess paint. This should help
the bolts fit in properly.
There are four spare bolts, which can be left on the sprue unless they
are needed.
Using pliers or tweezers, carefully grasp a bolt and fit into one of the
holes (arrow). The long smooth end of the bolt is fitted into the hole,
leaving the bolt’s hex head visible (inset).
Tip: if the bolt won’t press in, try swivelling it until you find a better fit.
You can use the flat face of the tweezer handle to press the bolts flush.
Stage 07: Building the Left Cylinder Head

AGORAMODELS LAMBORGHINI MIURA
6
5
6
Continue to press bolts into the other holes of the cover.
Repeat for the remaining bolts in the other cam shaft cover until all sixteen have been fitted.
Stage 07: Building the Left Cylinder Head

AGORAMODELS LAMBORGHINI MIURA
7
7
Next take the cylinder head and align the cam shaft cover (right) with
the slots for mounting as shown (arrows).
Stage 07: Building the Left Cylinder Head
Firmly press the cam shaft cover into place, checking the fit is flush
around the edges.
8
9
Take the cam shaft cover (left) and align it with the other side of the cylinder head. Press the cover firmly
into place.

AGORAMODELS LAMBORGHINI MIURA
8
10
The left cylinder head should look like this with both covers and all of the bolts installed.
Stage 07: Building the Left Cylinder Head
STAGE COMPLETE

AGORAMODELS LAMBORGHINI MIURA
9
XXX
Name
Cover bolt x20
Cam shaft cover (left)
Cam shaft cover (right)
STAGE 08 PARTS LIST
Next you will install sixteen cover
bolts into the next set of covers
ready for the right cylinder head.
Cover bolt x20
Stage 08: Installing Cover Bolts
Cam shaft cover (left)
Cam shaft cover (right)

AGORAMODELS LAMBORGHINI MIURA
10
1
3
2
4
Carefully cut sixteen cover bolts from their sprue at the point shown in
the photo.
Locate the sixteen holes on the cam shaft covers (circled).
There are four spare bolts, which can be left on the sprue unless they
are needed.
Using pliers or tweezers, carefully grasp a bolt by the ring around it
and fit into one of the holes as shown. The long smooth end of the bolt
is fitted into the hole, leaving the bolt’s hex head visible (inset).
Stage 08: Installing Cover Bolts

AGORAMODELS LAMBORGHINI MIURA
11
5
Continue to fit bolts to install all sixteen into the cam shaft covers.
Stage 08: Installing Cover Bolts
STAGE COMPLETE

AGORAMODELS LAMBORGHINI MIURA
12
XXX
Name
Cylinder head (right)
Cylinder head side cover x2
STAGE 09 PARTS LIST
For this stage you’ll fit the covers
onto the right cylinder head, then
attach side covers to both of the
cylinder heads.
You’ll need the left cylinder head
assembled in the first stage of
this pack, as well as the cam shaft
covers from the previous stage.
Cylinder head side cover x2
Stage 09: Building the Right Cylinder Head
and Attaching Side Covers
Cylinder head (right)

AGORAMODELS LAMBORGHINI MIURA
13
1
3
2
4
Take the cylinder head (right) and one of the side covers. On the back
of the cover, note the two mounting pins (inset).
Take the right cam shaft cover from Stage 8 and align it with the
cylinder head as shown.
Carefully press the pins of side cover into the two holes located on the
the cylinder head (circled) so that the front of the cover faces outwards
(inset).
Firmly press the cover into place.
Stage 09: Building the Right Cylinder Head
and Attaching Side Covers

AGORAMODELS LAMBORGHINI MIURA
14
5 6
Take the right cam shaft cover from Stage 8 and align with the other
side of the cylinder head.
Press the cover into place. The assembly should now look like this.
Stage 09: Building the Right Cylinder Head
and Attaching Side Covers
7 8
Take the left cylinder head assembly from Stage 6 and the remaining
side cover.
Fit the cover into the cylinder head as you did for step 2, pressing the
pins of side cover into the two holes of the cylinder head.

AGORAMODELS LAMBORGHINI MIURA
15
9
The two cylinder heads should now look like this. By placing them as shown with the side covers (arrows)
furthest away from each other, you can identify the right cylinder head from the left one for the next stage.
Stage 09: Building the Right Cylinder Head
and Attaching Side Covers
STAGE COMPLETE
Right cylinder head
assembly
Left cylinder head
assembly

AGORAMODELS LAMBORGHINI MIURA
16
XXX
Name
Distributor (left)
Distributor (right)
Air filter box cover
Air filter box screw x3
Screws type A x3
Air filter box conveyor
STAGE 10 PARTS LIST
In this stage you’ll assemble an air
filter box and fit distributors onto
the two cylinder heads.
Air filter box screw x3
Stage 10: Assembling the Right Air Filter Box
and Fitting the Distributors
Air filter box cover
Type A x3
Distributor (left)
Distributor (right)
Air filter box conveyor

AGORAMODELS LAMBORGHINI MIURA
17
1
3
2
4
Take the two cylinder head assemblies from Stage 9 and pair them
with the distributors.
Fit the right distributor (marked ‘R’) to the side of the right cylinder
head and secure in place using a type A screw.
The two distributors are marked with an ‘R’ and an ‘L’ to differentiate
the right from the left (circled). Note the notch (arrows) on each part
that will be used to correctly align the pieces when fitting to the
cylinder heads (inset, arrow).
Repeat for the left distributor and the left cylinder head, fixing it in
place with another type A screw.
Stage 10: Assembling the Right Air Filter Box
and Fitting the Distributors
Left
Right

AGORAMODELS LAMBORGHINI MIURA
18
5 6
The two cylinder head assemblies should now look like this with the
distributors attached.
Align the air filter box cover with the air filter box conveyor as shown.
Note the pins and their corresponding holes (arrows).
Stage 10: Assembling the Right Air Filter Box
and Fitting the Distributors
7 8
Push the cover into the conveyor until the parts fit firmly together. Next take the three air filter box screws and carefully push them into
the holes on cover (arrows). We recommend to do this by hand to
avoid damaging the paint and print on the cover.

AGORAMODELS LAMBORGHINI MIURA
19
9
The air filter screws should be flush with the filter box cover once they are in place.
Stage 10: Assembling the Right Air Filter Box
and Fitting the Distributors
STAGE COMPLETE

AGORAMODELS LAMBORGHINI MIURA
20
XXX
Name
Carburettor
Velocity stack x3
Inlet manifold x3
Shim plate x3
Support pin x2
STAGE 11 PARTS LIST
Next you’ll build the first of four
carburettors for this pack. Take care
when fitting the inlet manifolds,
as their orientation changes
depending on which cylinder head
the carburettor will be fitted onto.
Support pin x2
Stage 11: Left Carburettor (1)
Velocity stack x3
Shim plate x3
Carburettor Inlet manifold x3