Laminata Shed 900 User manual

Shed 900
Installation Guide
Ready. Set. Build.

Ready.
Set.
Build.

Measuring tape.
Laminata has created garden sheds focused on practical
and functional design. Our MiniCLT panels make up the
majority of the shed, ensuring strength and durability. The
TPO rubber membrane roofing keeps the water out and the
aluminum profiles cover the joins, making for a shed you’ll
be proud to have in your backyard!
Find out more.
www.laminata.nz
Ask us.
0508 526 462
Toolkit.
To get started you’ll need a few tools (not included).
Spirit level.
Pre-drill bit.
Drill.
Mallet hammer.

Getting started.
Materials list for Shed 900.
Timber.
Floor. Premade Base.
1733 x 825mm
Rear Wall. CLT Panels.
135 x 30 x 1790mm (tongue ON)
275 x 30 x 1790mm
275 x 30 x 1790mm (NO Tongue)
Side Walls. CLT Panels.
275 x 30 x 825mm
135-275 x 30 x 825mm (angle panels)
Front Wall. CLT Panels.
135 x 30 x 1790mm (NO Tongue)
275 x 30 x 298mm
135 x 30 x 298mm (tongue ON)
Roof. CLT Panels.
275 x 30 x 1790mm
275 x 30 x 1790mm (no tongue)
Doors. Premade doors.
590 x 1785mm
1x
1x
5x
12x
2x
1x
12x
2x
3x
2x
1x
1x

Other.
Roof. Equal Angle.
40 x 40 x 1800mm
40 x 40 x 1100mm
Roof. TPO Rubber Roofing.
1160 x 1800mm
Corners. Equal Angle.
40 x 40 x 1925mm
40 x 40 x 1800mm
Door Jams/Frames. Equal Angle Channel.
31.75 x 31.75 x 1785mm
Hardware.
8g x 65mm Screw (Square head)
8g x 30mm Self-Tapping (Phillips)
8g x 40mm Self-Tapping (Phillips)
Door Hinge
Pad Bolt
2x
2x
1x
2x
2x
200x
100x
32x
4x
2x
2x

Note.
It pays to itemise all
components prior to
assembly.
Step 01.
Getting started.
Prepare your work space.
Ensure your premade base sits
stable and level.

7
Step 02.
Attaching your rst layer.
First.
Using 2x planks 275 x 28 x 825mm
place them on top of the bearer
overhang and screw fix 3x screws 8g x
65mm into the premade base.
Panels should sit flush and square
with the premade base.
Next.
Screw fix 1x CLT plank (tongue on)
135 x 28 x 1790mm to the rear of the
premade base, securing it to both the
side panels
above and the premade base with
6x screws 8g x 65mm.
Note.
For strength, the
panels are staggered.

Step 03.
Build up the walls.
Note.
The top rear wall
panel has no
tongue.
Continuing the staggered pattern,
build up the rear and side walls using
5x CLT panels 275 x 28 x 1790mm,
1x CLT Panel (no tongue) 275 x 28 x
1790 and 12x CLT panels 275 x 28 x
825mm.
Construct one layer at a time fixing
2x screws 8g x 65mm from the rear
wall panels into the sidewall panels.

9
Step 04.
Add the roof angle and lintel.
First.
Using the 2x CLT panels (angle panels)
135-275 x 28 x 825mm screw fix them
as per step 2/3 to finish the side walls.
Next.
Screw fix the 1x CLT panels (groove on)
135 x 28 x 1790mm to the top of the
front wall.
Note.
This is a good time
to ensure your
shed is level and
square.

Step 05.
Installing front wing walls.
Note.
Skew screw the
first CLT panel 275
x 28 x 298mm
up into the lintel,
ensuring this join is
tight and square.
First.
Using the 12x CLT panels 275 x 28 x
298mm, screw fix from the top down
with 2x screws 8g x 65mm in each
plank.
Next.
Finish at the bottom with the 2x CLT
panels (tongue on) 135 x 28 x 298mm
fixing to both the side walls and base.

11
Step 06.
Putting the roof on.
Using 3x CLT panels 275 x 28 x
1790mm, start from the back,
overhanging the first plank 100mm past
the rear wall.
Screw fix down into the side and rear
walls with screws 8g x 65mm. Install
the other 2 panels, ensuring they are
square with the side walls.
Place the 1x CLT panel (no tongue)
275 x 28 x 1790mm at the front with
100mm overhang.
Note.
Fix the front and
rear roof panel
down to the front
and rear wall.

Step 07.
Coating (optional).
Note.
Choose dark
colours to avoid
damage to the
timber substrate.
To protect your new shed, we suggest
staining with a suitable outdoor
timber stain prior to installing
aluminum profiles and roofing.
We suggest using a Cabot’s water or
oil based stain with a Cabot’s broom
applicator.

13
Step 08.
Install TPO rubber roong.
Roll out the TPO rubber membrane
over the roof panels and tac with
either a staple gun or small screws
around edges.
Note.
You can also
glue down the
membrane.

Step 09.
Aluminium proles.
Using the Self Drilling 8g x 30mm,
fix the aluminum channels to the
applicable joins and corners;
2x Roof Equal Angle
40 x 40 x 1800mm
2x Roof Equal Angle
40 x 40 x 1100m
2x Door Jams
31.75 x31.75 x 1785mm
2x Corners Equal Angle (front)
40x40x1.925m
2x Corners Equal Angle (rear)
40 x 40 x 1800mm
Note.
Pre-drill hobs with
a 3mm pre-drill bit
to make attaching
aluminium easier.

15
Step 10.
Doors and hardware.
Attach the door hinges to the premade
doors, ensuring they are positioned
correctly for the doors to open
outward. Evenly space the hinges to sit
100mm from both the top and bottom
of the door.
When hanging the doors ensure they
sit square with the door jams and level
with even gaps top and bottom. Install
door hardware to suit your preference.
Note.
If doors don’t sit
straight, double
check your shed
is sitting level and
adjust accordingly.

Find out more.
www.laminata.nz
Ask us.
0508 526 462
Ready. Set. Build.