Lang GhosT-OLED-I User manual

GhosT-OLED Series
Manual
Date
Revision No.
Author
1
st
Check
Final Check
Description
28.09.2016
1.0 BVT/TSN/DWN TSN First Draft

2
TABLE OF CONTENT
1. Important information 4
1.1 Safety instructions 4
1.2 Damage prevention 4
1.3 Operating conditions 5
2. Overview Ghos -OLED Series 5
2.1 Introduction 5
2.1.1 Ghos -OLED-I (Installation) 6
2.1.2 Ghos -OLED-P (prime OUCH) 6
2.2 Ghos -OLED Setup Versions 7
2.2.1 Ghos -OLED able-Stand Version ( V) 7
2.2.2 Ghos -OLED Straight Version (SV) 7
2.2.3 Ghost -OLED Straight Offset Version (SOV) 8
3. Scope of delivery 9
4. Pack-/ and unpack-instructions 10
4.1 able-Stand Version 10
4.2 Straight Version & Straight Offset Version 12
5. Installation instructions 14
5.1 Mechanical installation 14
5.1.1 Installations tools and materials 14
5.1.2 Screw hole pattern 15
5.2 Installation possibilities 16
5.2.1 Ghos -OLED able-Stand Version 16
6. Connector panel and control possibilities 19
6.1 Power Input, IR-Receiver and optional touch 19
6.2 Video input connectors 20
6.3 Local control 21
6.4 External Control Connectors 21
6.4.1 Remote control 22
6.4.2 On-Screen-Display (OSD) menu guide 23
6.4.3 Web interface 24
7. prime OUCH option 25
8. Content Guide 25
8.1 Pixel Shift 25
8.2 ransparency 26
8.3 Static content 26

3
9. roubleshooting 27
10. Specifications 27
11. Product outlines 29
11.1 Drawings Ghos -OLED-I 29
11.1.1 able-Stand Version 29
11.1.2 Straight Version 30
11.1.3 Straight Offset Version 31
11.2 Drawings Ghos -OLED-P 32
11.2.1 able-Stand Version 32
11.2.2 Straight Version 33
11.2.3 Straight Offset Version 34
12. Certification 35
Note: These installation instructions must always be handed over to the installing person1
Note: Read these instructions carefully before installing the system
Copyright © 2016 LANG AG. All rights reserved.
1 Only a qualified person should install this product

4
1. Important information
The GhosT-OLED series has een designed under the highest attention on safety. However, improper
handling can cause a risk for safety and/ or damage. Please read carefully the instructions provided in
this manual in order to avoid damage and ensure personal safety. Heeding the instructions will also
prevent image retention and extend the products lifetime. The GhosT-OLED products are intended for
use y fully qualified, trained and competent persons as an aid to provide safe and secure
installations.
1.1 Safety instructions
• Do not open the housing of the display otherwise electric shocks may occur. There is no need
for users to open the housing of the display. Please refer to Lang-AG for any service works.
• Do not expose the screen to water or moisture to prevent electric shocks.
• If the screen or the housing reaks, e very careful as roken fragments may cause injuries.
Do not touch roken glass with are hands, use appropriate safety tools
• If the screen or the housing is roken, always unplug all power supplies and other ca les from
the display to prevent electric shocks.
• Do not use the system in other operating conditions than descri ed in chapter 1.3 Operating
conditions.
• In cause of injury, for example caused due to contact with roken glass, please seek medical
help immediately
• Do not mount the GhosT-OLED displays to unsta le structures, the entire system might fall
down or tilt over. Make sure that the construction to which a display is mounted can support
the given total weight (for weight details please referr to: 10.Specifications)
1.2 Damage pre ention
• Do not expose the screen to water or moisture to prevent any damage.
• Avoid any force or impacts on the screen.
• If the screen is roken, always unplug all power supplies and other ca les from the display to
prevent damage to electronical parts.
• Set up the screen in a well ventilated place.
• The recommended operating time is less than 12 hours a day.
• Static images on the display can cause image retention. To prevent such damage, it is
recommended to show dynamic content periodically. Refer to 19. Content recommendations
for furthermore information.
• Do not expose the display to sunlight or any UV light sources as UV light can cause damage
to the screen.
• Always operate the system under the specified operating conditions descri ed in chapter 1.3
Operating conditions.

5
1.3 Operating conditions
• Temperature: 25 +/-10°C
• Humidity: 55 +/-20% rH
• Operating time: less than 12 hours a day
• isplay pattern should be changing continuously to avoid any kind of image retention
• No sunlight or any other warm light sources directed onto the screen
• Only indoor operation
• isplay must be protected from UV light
• Usage only in well ventilated environments
2. O er iew GhosT-OLED Series
2.1 Introduction
Displays from GhosT-OLED series are transparent OLED (T-OLED) screens in Full-HD resolution
with low temperature poly silicon TFTs. The transmittance of the screen is approx. 45% (excluding
cover glass). Thanks to OLED (Organic Light Emitting Diode) technology, the display shows
excellent images even at high viewing angles and has very low power consumption. The
transparency is achieved y adding a fourth segment into the su pixel structure which usually
consists of three su pixel emitting red, green and lue light. This fourth segment is transparent
and compared to the other su pixel the largest one. As OLED is a self-emitting technology, there
is, unlike to LCDs, no need for acklight. Displaying lack content on a transparent OLED display
will make this content appear transparent. GhosT-OLED displays are onded with an anti-
reflective, tempered front glass and are optionally availa le with a primeTOUCH system ased on
IR diodes. GhosT-OLED displays can e delivered with white or lack housing.
The GhosT-OLED series is ased on a customiza le design concept. There are two different
versions availa le, each with three varia le ways to install them. With this portfolio GhosT-OLED
Series offers a standard solution for many applications.

6
2.1.1 GhosT-OLED-I (Installation)
This version provides a frameless glass surface, thinner than 9 mm. With its frameless ut ro ust
design the GhosT-OLED-I version is perfect for exclusive, futuristic installations. The display is
availa le in each of the three installation options where y the Ta le-Stand Version is pictured
elow.
Figure 1: GhosT-O ED-I, TV Option
2.1.2 GhosT-OLED-PT (primeTOUCH)
This version com ines the advantages of the T-OLED technology with the multi touch capa le
primeTOUCH technology. Despite touch capa ility it provides a narrow ut sta le frame. The
display is availa le in each of the three installation options where y the Ta le-Stand Version is
pictured elow.
Figure 2: GhosT-O ED-PT, TV Option

7
2.2 GhosT-OLED Setup Versions
The three different setup versions for GhosT-OLED-I and -PT will e descri ed riefly in the following
passage. Please note: All images present the GhosT-OLED-I, ut asically the same applies also to
GhosT-OLED-PT.
2.2.1 GhosT-OLED Table-Stand Version (TV)
For flexi le use and fast setup the Ta le-Stand Version is recommended. Mounting points on the
ottom side of the display ena le portrait mode, face up installations and setups to angled
surfaces. The design of the ta le foot allows convex display arrays with angles up to 90°.
Figure 3: GhosT-O ED-I, TV Option, backside
2.2.2 GhosT-OLED Straight Version (SV)
The Straight Version is designed for space-saving installations like in podiums, alustrades or
counters. It’s quick and easy to install y using the mounting points in the front.
Figure 4: GhosT-O ED-I, SV Option, backside

8
2.2.3 GhostT-OLED Straight Offset Version (SOV)
The straight-offset version provides all the advantages of the Straight Version with an additional
mounting surface for leveled installations. It uses the same mounting points as the Straight
Version.
Figure 5: GhosT-O ED-I, SOV Option, backside

9
3. Scope of deli ery
Note: Please check the delivery for completeness and damage immediately after you receive the
shipment. Please contact your supplier in case of missing or damaged parts.
Power ca le USB ca le USB extender
External IR-sensor Remote control USB stick
Illustrated list of mentioned accessories
GhosT-O ED-I delivery scope
Quantity Item
1 GhosT-OLED-I
1 Power ca le
1 Remote control
1 External IR-Receiver
1 USB stick (tools & info)
GhosT-O ED-PT delivery scope
Quantity Item
1 GhosT-OLED-PT
1 Power ca le
1 Remote control
1 External IR-Receiver
1 USB stick (tools & info)
1 USB ca le (A type)
1 USB extender (A type)

10
4. Pack-/ and unpack-instructions
GhosT-OLED units get shipped in a functional flight case designed for all three installation versions.
Caused y the universality the units get inserted upside down.
Note: Read the following instructions carefully to prevent injuries to humans or damages to the
system and environment.
Note: GhosT-OLEDs provided as straight-/ or straight-offset version have to e mounted right after
unpacking. There is no possi ility to place them on a ta le or on the floor intermediately.
Note: For packing and unpacking a unit at least two persons are required.
4.1 Table-Stand Version
Description Illustration
1. Make sure that the rakes of the flight
case are tightened
2. Open the front cover of the flight case
3. Open the top cover of the flight case
1. Lift the unit out of the flight case
carefully y considering the guiding slot
on the ottom side of the flight case
2. Rotate the unit y 180° degrees and set
it down carefully
3. Attach the display to the exhi ition
furniture referring to 5 Installation
instruction
2
3
1
2
3
Guiding-
Slot
1

11
1. The glass surface of the GhosT-OLED-I
version is protected with an additional
foam cover. Remove the cover carefully
and store it safely.
Note: For packing follow the provided steps ackwards
1
Glass surface
Foam cover
User side

12
4.2 Straight Version & Straight Offset Version
Description Illustration
1. Make sure that the rakes of the flight
case are tightened
2. Open the front cover of the flight case
3. Open the top cover of the flight case
Straight Version
1. Lift the unit out of the flight case
carefully y considering the guiding slot
on the ottom side of the flight case
2. Rotate the unit y 180° degrees
3. Align the unit to the construction of the
exhi ition furniture carefully
4. Attach the unit to the exhi ition furniture
referring to 5 Installation instruction
Straight Offset Version
1. Lift the unit out of the flight case
carefully y considering the guiding slot
on the ottom side of the flight case
2. Rotate the unit y 180° degrees
3. Align the unit to the construction of the
exhi ition furniture y using the angled
mounting surface
4. Attach the unit to the exhi ition furniture
referring to 5 Installation instruction
Guiding
Slot
2
3
1
1
2
3
4
Guiding
Slot
1
2
3
4

13
1. The glass surface of the GhosT-OLED-I
version is protected with an additional
foam cover. Remove the cover carefully
and store it safely.
Note: For packing follow the provided steps ackwards.
1
Glass surface
Foam cover
User side

14
5. Installation instructions
5.1 Mechanical installation
All versions of the GhosT-OLED series are ased on the same housing system which makes them
easy and fast to setup. Before you start installing the screen, follow the instructions provided in 3
Scope of delivery and 4 Pac -/ and unpac -instructions.
Note: Read the following instructions carefully to prevent injuries to humans or damages to the
system.
Note: For mounting the GhosT-OLED at least three persons are required.
Note: Use only the required tools and mounting materials.
5.1.1 Installations tools and materials
Quantity
Description Illustration
1 • 5mm HEX key
up to 14
• M6 x 16 mm + surface thickness
 Note: The screw size always needs to e
16 mm longer than the surface thickness of
the exhi ition furniture.
 Note: The head shape of the screw
depends on the conditions of the mounting
area.
 Note: The num er of availa le screw holes
depends on the given version and
installation option.
 Note: Min. 8 screw holes have to e used
up to 14 • 6,4 mm washers
Note: The use of safety washers is
recommended in most cases. This depends on
the material of the mounting area

15
5.1.2 Screw hole pattern
Version Screw hole pattern in mm [In]
GhosT-
OLED-I
Note: The red marked area cannot e used.
GhosT-
OLED-PT
Note: The red marked area is only availa le in case of using the Ta le-Stand Version

16
5.2 Installation possibilities
5.2.1 GhosT-OLED Table-Stand Version
Set up on leveled surfaces, the GhosT-OLED TV option is a le to run without additional mounting,
ut it’s recommended to mount at least 4 screws to the exhi ition furniture to hold the unit in place.
It’s also made for angled surfaces or portrait mode applications. Therefore the Ta le-Stand
Version provides min. 8 mounting points on the ottom side of the ta le foot. The length of the
screw depends on the surfaces thickness. Please refer to 5.1.1 Installations tools and material.
Figure 6: Installation example GhosT-O ED-PT TV Option

17
5.2.2 GhosT-OLED Straight Version
The GhosT-OLED Straight Version can only e mounted correctly y using all of the provided
mounting points. Therefore it’s required to work in a team of at least three persons. Two persons
are needed to align the display to the screw-hole pattern while the third person can insert the
screws into the mounting points.
Figure 7: Installation example GhosT-O ED-PT SV Option

18
5.2.3 GhosT-OLED Straight Offset Version
The GhosT-OLED Straight Offset Version can only e mounted correctly y using all of the
provided mounting points. Therefore it’s required to work in a team of at least three persons. Two
persons are needed to align the display to the screw-hole pattern while the third person can insert
the screws into the mounting points. This version has the advantage that it’s possi le to load the
weight to the angled mounting surface while installing.
Figure 8: Installation example GhosT-O ED-PT SOV Option

19
6. Connector panel and control possibilities
All versions share a similar connector panel on the ackside of the ta le foot.
Figure 9: GhosT-O ED connector panel
6.1 Power Input, IR-Recei er and optional touch
These components are located at the lower right side of the connector panel like shown elow:
a
c
d

20
Description
technical design
a AC IN connector IEC socket
Main Power switch 2 pin rocker switch
c primeTOUCH USB (optional) USB type A, female
d External IR-receiver input 3,5 mm jack, female
6.2 Video input connectors
The GhosT-OLED provides three different video input connectors. All of them are located at the
upper left side of the connector panel like shown elow: The native input timing for the GhosT-
OLED series is 1920 y 1080 @60p. The display will accept other timings as well and most likely
display them, ut the results might not y sufficient. The panel will always work with 60p refresh
rate even if the input frame rate might e different.
Description
technical design
a DVI connector DVI-D, female
VGA IN Mini D-su , 15 pin, female
c DISPLAYPORT connector DISPLAYPORT, female
d Audio input
Note: cannot e used
No function
a
c
d