Laresar L6 Pro User manual

CONTENTS
IMPORTANT SAFETY WARNING1
PRODUCT INFORMATION
3
MAINTENANCE
4.1 Product Assembling
4.2 Wall-Mount Plate
4.3 Clean the Infrared Lens/Charging and Dust Collection Sensor Head
4.4 Clean the Filter Screen of the Fan
4.5 Clean the Main Brush
4.6 Clean/Replace the Side Brush
4.7 Clean the Sensor
4.8 Battery Maintenance
4.9 Clean the Two-in-one Water Tank
4
SPECIFICATION
5
TROUBLESHOOTING
6
WARRANTY
7
DISPOSAL8
PACKING LIST
2
--------------------------------------------------
--------------------------------------------------------------------------
-----------------------------------------------------------
--------------------------------------------------------------------------
--------------------------------------------------------------------------
--------------------------------------------------------------------------
--------------------------------------------------------------------------
--------------------------------------------------------------------------
02
04
05
07
13
14
17
18
-----------------------------------------------------------------------------------
---------------------------------------------------------------------------------------
-----------------
----------------------------------------------------------------
--------------------------------------------------------------------------------
---------------------------------------------------------------------
--------------------------------------------------------------------------------------
----------------------------------------------------------------------------------
----------------------------------------------------------------
07
08
09
09
10
10
10
11
11
01
EN
If you have any questions, please email to [e-mail]

1. IMPORTANT SAFETY WARNING
ATTENTION: Before using this machine, please read all instructions in the
manual and cautionary markings on the machine carefully.
This user's manual includes information for Regulatory Models: Laresar L6 Pro Robot Vacuum
Cleaner and Laresar LS-03 Dust Collection Charging Base.
This device is for indoor use only. Do not use outdoors or on wet surfaces. A physical barrier
should be used to prevent access to the balcony and to ensure safe operation.
Do not use this device on an unfinished, unsealed, waxed or rough floor. It may result in
damage to the floor and this device. Use only on hard floor surfaces or low-pile carpet.
This device has been designed to be used on floors without scratching them. We still recom-
mend that you test this device on a small area of the room to be cleaned to ensure no scratch-
es are made before cleaning the whole room.
Do not use this device to pick up spills of bleach, paint, chemicals, or anything wet.
Do not use this device to pick up anything that is burning or smoking.
Do not pour any liquids into the device and do not immerse in water.
This device can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of this device in a safe way and understand
the hazards involved.
Children should be supervised to ensure they do not play with this device. Cleaning and
maintenance shall not be performed by children without adult supervision.
This device is not a toy. Do not sit or stand on this device. Small children and pets should be
supervised when this device is operating.
Before using this device, pick up objects like clothing and loose paper. Lift up cords for blinds
or curtains, and move power cords and fragile objects out of the way. If this device passes
over a power cord and drags it, an object could be pulled off a table or shelf.
Range of Usage
About the Appliance Use
Children and pets should be supervised when the charging base is operating.
Do not sit or stand on this charging base.
Do not use without dust bag and/or filters in place.
Do not put any object into openings. Do not use with any opening blocked, keep free of dust,
lint, hair, and anything that may reduce air flow. Do not place foreign objects inside and ensure
it is clear of debris.
Risk of electric shock, use this charging base in dry location only.
Do not handle plug or appliance with wet hands.
About the Charging Base Use
02
EN
If you have any questions, please email to [e-mail]

This device is only to be used with the power supply unit (LS-03) provided.
The battery must be removed from this device before this device is disposed of.
This product comes with a region approved power supply cord and is designed to be plugged
into a standard household AC power outlet only.
Product may not be used with any type of power converter. Use of power converters will imme-
diately void the warranty.
If you live in an area prone to electrical storms, it is recommended that you use additional
surge protection.
The external flexible cable or cord of the power supply unit cannot be replaced, if the cord is
damaged, the power supply unit shall be disposed of.
If it will be not used for a long time, fully charge the appliance, turn it off and put in a cool and
dry place. Charge the appliance at least once every 3 months to avoid battery damage dut to
over discharge.
Notes on Charging
Store and operate this device in room temperature environments only.
Do not place the charging base close to heat sources (such as radiator).
To reduce the risk of electric shock, unplug your dirt disposal before cleaning or maintaining
the product.
Clean with a cloth dampened with water only.
Do not place anything on top of this device.
Do not expose or disassemble the electronics of this device, its battery, or the integrated
Charging Base. There are no user-serviceable parts inside. Refer servicing to qualified
service.
If you need to transport the product, make sure that the appliance is turned off and it is recom-
mended to use the original package.
About Storage and Maintenance
WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one more of the follow-
ing measures:
FCC STATEMENT
03
EN
If you have any questions, please email to [e-mail]

2. PACKING LIST
SAVE THESE INSTRUCTIONS
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Pic Name
L6 Pro Robot Vacuum
Cleaner
Dust Collection
Charging Base
In the package
In the package
1
1
Two-in-One Water Tank On the robot vacuum
1
Mop Cloth Support On the robot vacuum
1
Mop Cloth
1pcs on the robot
vacuum,1pcs is a gift in the
package
2
Disposable Mop Cloth Gifts, in the package
10
Dust Bag
1pcs on the dust collection
charging base, 4pcs are gifts
in the package
5
Filter Screen 1pcs on the robot vacuum,
1pcs is a gift in the package
2
Qty Place
04
EN
If you have any questions, please email to [e-mail]

3. PRODUCT INTRODUCTION
Infrared sensor
Lidar
Anti-collision strip
Infrared sensor
Bumper
Recharge button/indicator
Short press once to recharging
Power button/indicator
Long press for 3 seconds to turn on or off
Short press once to start global cleaning or
pause cleaning
Robot Vacuum Cleaner
Main Brush On the robot vacuum1
1
1
1
1
Side Brush
Cleaning Knife
After-Sales Service
Card
User Manual
Quick Start Guide
Manual
1pcs on the robot vacuum, 1pcs
is a gift in the package
On the dust collection charging
base
In the package
In the package
In the package
2
User Manual
05
EN
If you have any questions, please email to [e-mail]

Indicator Reminder
*Indicator status definition :
Breath: Gradually on and off in 4 seconds
Slowly flash: On for 0.7 seconds, off for 0.8 seconds
Faster flash: On for 0.1seconds, off for 0.2 seconds
Mop cloth assembly
Main brush cover
Side wheel
Cliff sensor
Caster
Main brush
Side wheel
Side brush
Cliff sensor
Machine status Status of power indicator
Stand by/pause
Charging
Pause
Cleaning/remote control
Recharging
Abnormal
Turned off
Wi-Fi not connected
Wi-Fi connected
Wi-Fi being connected
Blue light long bright
Blue light breath
Blue light slowly flash
Blue light long bright
Light off
Red light fast flash
Blue light fast flash
Blue light slow flash
Blue light long bright
Blue light long bright
Light off
Light off
Light off
Light off
Orange light long bright
Light off
Light off
Light off
Light off
Light off
Status of recharge indicator
06
EN
If you have any questions, please email to [e-mail]

4. MAINTENANCE
Dust Collection Charging Base
4.1 Replace the Dust Bag
When the dust bag is full, the FULL UP sign is keeping high brightness,
and app notice is given. Please replace the dust bag in time.
Charging electrode tip
Dust bin release button
Dust bag chamber
Upper cover
Screen
Dust bag is full: The light will be
bright
Dust bag is not installed
correctly: The light will flash
During dust collection: The lamp
is bright and flashing
Full power: Two grids green
long light
Power≤50%: A grid green long
light
Infrared len
Suction inlet
Charging and dust
collection sensor head
Reset button
Wall-following TOF
sensitive detector
Press and hold for 1 second to restart
“ ”
07
EN
If you have any questions, please email to [e-mail]

4.2 Clean the Dust Passage
If all signs are twinkling after the dust bag is replaced, it is recommended
to pull out the power plug and reverse the dust collection charging base
to check whether there are foreign maters blocking the dust passage.
If the dust passage is blocked, remove the transparent cover of the dust
passage with a screwdriver to remove foreign matters.
Note: Violent disassembly is prohibited. After cleaning, replace the cover as it is.
The COLLECTING sign will be high brightness while the collector is
working.
125Open the upper cover Pull up the lifting handle
of the dust bag and take
out the dust bag
Throw away the used
dust
Install a new dust bag
Close the upper cover
！“ ”
08
EN
If you have any questions, please email to [e-mail]

4.3 Clean the Infrared Lens/Charging and Dust Collection Sensor Head
4.4 Clean the Filter Screen of the Fan
Wipe them gently with a clean, soft, dry cloth. It is recommended to clean them once a month.
The filter screen of the fan is below the dust bag. If there is dust accumulation, wipe it gently with
a clean, soft, dry cloth. It is recommended to clean them once a month.
Transparent cover of the dust passage
Dust Passage
Infrared lens
Fan filter screen
Charging and dust collection sensor head
09
EN
If you have any questions, please email to [e-mail]

4.5 Clean the Main Brush
4.6 Clean/Replace the Side Brush
4.7 Clean the Sensor
The main brush is consumable and should be cleaned at least once a week. It is recommended to
replace the main brush every 6-12 months to ensure the cleaning effect.
The side brush is consumable. It is recommended to replace it every 3-6 months to ensure the
cleaning effect. Remove or install the side brush with a screwdriver.
It is recommended to use a clean, soft, dry cloth to wipe each sensor gently every week to ensure the
normal use of the machine.
Remove Install
① Reverse the robot vacuum, press the snap on the main brush cover, and remove
the main brush cover and the main brush.
② Cut off the hair wound on the main brush with the cleaning knife.
③ Replace the main brush and the main brush cover. Press and fasten the snap.
Note: Avoid hitting when reversing the robot to prevent damage to the lidar.
！Main brush cover
Main brush
10
EN
If you have any questions, please email to [e-mail]

4.8 Battery Maintenance
4.9 Clean the Two-in-one Water Tank
The robot vacuum has a built-in high-performance rechargeable lithium-ion battery pack. In order
to maintain battery performance, please keep the battery pack charged every day.
If the machine will not be used for a long time, please turn it off and store properly. Charge it at
least every 3 months to avoid battery damage due to over discharge.
② Open the dust bin by pressing the dust
bin snap.
① Press and hold the release button of the
two-in-one water tank and at the same time
pull it outwards.
Senor of the Robot Vacuum
Cliff sensor ×4
Infrared sensor ×3
Charging electrode tip ×2
Wall-following TOF sensitive detector x1
Infrared len ×2
Charging and dust collection sensor head ×2
Senor of the Charging Base
Wall-following
position sensitive
detector
Infrared sensor
Cliff sensor
Infrared sensor
Infrared sensor
Charging
electrode tip
Charging
electrode tip
Infrared lens
Charging and dust
collection sensor head
11
EN
If you have any questions, please email to [e-mail]

③Remove the filter screen clip. ④Take out the filter screen.
⑤ Remove the debris on the filter
screen and screen clip with a
cleaning brush.
⑦ Open the water tank cover and inject an appropriate amount of water.
⑥ Turn on the tap to clean
the dust bin.
Tips: The filter screen is consumable. It is recommended to replace it every 3-6 weeks. You
can make a purchase through the official channel.
！Tips: It is suggested to use pure water without any cleaning agent.
！12
EN
If you have any questions, please email to [e-mail]

5. SPECIFICATION
⑧ Please remove the water tank fittings from the machine according to the illustration and reverse
it, remove the mop or replace it.
Tips:
！If the mop is too dirty, it will affect the effect of mopping, please clean it in time.
Be sure to remove the mop for cleaning and screw it dry before installation. It is forbidden to clean
on the two in one water tank.
The mop is a consumable and it is recommended to replace it every 3-6 weeks.
Product name
Robot Vacuum Cleaner
Product model
Product dimensions
Input of robot vacuum
Rated power of robot vacuum
Operating voltage of robot vacuum
Battery type
Battery capacity
Wireless connection
Output of dust collection charging pile
Rated power of dust collection
charging pile
Product dimensions
24V 1.2A
950W
253 x 210 x 350 mm
Intelligent Cleaning Robot
Vacuum Cleaner
L6 Pro
349 x 100 x 353 mm
24V 1.2A
50W
14.4V
Lithium ion battery pack
5200mAh
Wi-Fi IEEE 802.11b/g/n 2.4GHz
Dust collection Charging Base
13
EN
If you have any questions, please email to [e-mail]

6. TROUBLESHOOTING
When the machine runs abnormally, the power indicator will blink in orange, and the machine will give
a voice prompt when some faults occur. Please refer to the table below for a solution.
Voice prompt/
fault phenomena
Please check if the
radar is stuck
The radar is blocked
or stuck
Remove the obstacle or move
the machine to an open place
and restart it
Please check the anti-colli-
sion rail
The bump sensor is
stuck
Clean up the foreign matters
around the anti-collision rail, or
move the machine away
Please wipe the cliff sensor
and move away from the
dangerous area to restart
The cliff sensor is
triggered after the
machine is started up
Please wipe the cliff sensor
and move the machine to a flat
and open place to start
Please check the main brush The main brush is stuck Clean the main brush, or move
the machine away
Please check the side brush The side brush is stuck Clean the side brush, or move
the machine away
Please check the main wheel The main wheel is stuck Clean the main wheel, or
move the machine away
The two-in-one water tank is
taken out
The two-in-one water
tank has been taken out
Please replace the two-in-one
water tank and the filter
screen, and confirm that the
filter screen and the
two-in-one water tank are
installed in place
Low battery, start recharging Low battery during
cleaning
Low battery. Please charge the
robot before using
The fan is abnormal The fan is abnormal Please try to turn the machine
off and then restart it
Please wipe the wall-follow-
ing position sensitive
detector on the right side
The wall-following
position sensitive
detector is abnormal
Please wipe and clean the
wall-following position
sensitive detector
Possible causes Solution
14
EN
If you have any questions, please email to [e-mail]

The radar cover is pressed The radar cover is stuck
The radar is pressed or
stuck. Please move it to
another position to start
The battery is damaged or
not installed
The battery has abnormality
during charging
The battery temperature is
too high or too low. Please
wait for the battery tempera-
ture to return to be normal
before use
The machine cannot be
started up
Low battery level or
abnormal ambient- tempera-
ture
The battery level is low.
Please charge it before use.
The ambient temperature is
too low (below 0 or too high
(above 50 °C). Please use
the product in the environ-
ment of 0 °C ~ 40 °C
Cannot be charged
1. The dust collection
charging pile is not electrified
2. The charging electrode tip
is dirty
3. The charging electrode tip
has poor contact
1. Please confirm that the
power cord of the dust
collection charging pile is
connected to the power
supply
2. Regularly clean the
charging electrode tip of the
machine and the dust
collection and charging
sensor head of the dust
collection charging pile
3. Please eliminate the poor
contact caused by the side
brush or other foreign
matters, and try to reposition
the machine manually
Recharging failed, dust
collection charging pile not
found
1. The dust collection
charging pile is blocked or
too far away
2. The dust collection
charging pile is not connect-
ed to the power supply
3. There are foreign matters
at the bottom of the mop
cloth support or the mop
cloth is rolled up
1. Please put the dust
collection charging pile in the
open area, and put the
machine near the dust
collection charging pile to
retry
2. Please connect the dust
collection charging pile to the
power supply
3. Please clean up the bottom
of the mop cloth support and
tidy the mop cloth
Abnormal behavior Program exception Turnoff and restart
15
EN
If you have any questions, please email to [e-mail]

There are abnormal sounds
during cleaning
Foreign matter wound on the
main brush/side brush or the
main wheel
Please turn off the machine
for cleanup
Regular cleaning does not
work
Low battery
Regular cleaning can only be
started when the remaining
battery level is greater than
30%. Please keep the
machine charged every day
Cannot be connected to APP Abnormal Wi-Fi network,
wrong Wi-Fi password or
abnormal APP
1. Please ensure that the
machine is in a good Wi-Fi
signal area
2. Re-enter the Wi-Fi
password or reset Wi-Fi
download and connect the
latest version of APP
The floor mopping module
outputs no water or little
water
No enough water in the
water tank, too dirty mop
cloth or the mop cloth
support not installed in place
1. Please check whether
there is water in the water
tank
2. Dean the mop cloth
3. And install the mop cloth
correctly according to the
instructions
The floor mopping module
outputs too much water
The water tank cover is not
in place, and the water
output is adjusted to the
maximum
Please confirm that the water
tank cover is installed in
place, and adjust the
appropriate amount of water
in the APP
The dust collection perfor-
mance degrades
Dust accumulates in the dust
bag, causing the air flow into
the suction nozzle to
decrease
Replace the dust bag
Cannot return to the dust
collection charging pile after
fixed-point cleaning or
moving
The robot constructs a new
map or the distance is too far
After fixed-point cleaning or
moving for a long distance,
the robot will generate a new
map. If the dust collection
charging pile is far away, the
robot may not be able to
recharge automatically.
Please manually put the
machine back to the dust
collection charging pile for
charging
16
EN
If you have any questions, please email to [e-mail]

7. WARRANTY
The 1-Year Limited Warranty
WHAT IS COVERED?
According to the requirements outlined in this instruction manual, subject to the following conditions and
exclusions.
Only applies to purchases made from authorized retailers of Laresar.
This warranty will only be valid if the machine is used in the country in which it was sold.
WHAT IS NOT COVERED?
Laresar shall not be liable for costs, damages or repairs incurred as a result of:
Machines purchased from an unauthorized dealer.
Careless operation or handling, misuse, abuse and/or lack of maintenance or use not in accordance with the
Laresar Instruction Manual.
The machines are used for commercial or rental purposes in addition to normal domestic use.
Use of parts not in accordance with the Laresar Instruction Manual.
Use of parts and accessories other than those produced or recommended by Laresar.
External factors unrelated to product quality and use, like accidental water damage.
Repairs or alterations carried out by unauthorized parties or agents.
Normal wear and tear, including Water Tank, Filter, HEPA, Main Brush, Side Brush and Power Cord (or where
external damage or abuse is diagnosed), carpet or floor damage due to use not in accordance with manufac-
turer's instructions or failure to turn the brush roller off when necessary.
Reduction in battery discharge time due to battery age or use.
Your Laresar machine has a 1-year warranty against original defects in material and workman-
ship, when used for private household purposes in accordance with the Laresar Instruction
Manual.
This warranty provides, at no extra cost to you, all labor and parts necessary to ensure your
machine is in proper operating condition during the warranty period.
In case of abnormal operation of the dust collection charging pile, APP will give a message on the
phone.
Voice prompt/
fault phenomena
Possible causes Solution
Dust collection failed
The dust bag is missing or not
installed in place
The fan starts overheat
protection or has faults
Please install the dust bag
correctly, and try to collect
dust again 30 minutes later,if
it can’t be solved, please
contact after-sales customer
service
The dust bag is full
or Mocked
The dust bag is full or blocked
Replace the dust bag, and
clean the dust collection
charging pile (suction inlet,
dust passage, fan filter
screen, etc.) in time
17
EN
If you have any questions, please email to [e-mail]

8. DISPOSAL
Steps for removing the battery
Notes:
HOW TO CLAIM?
Please keep your proof of purchase. To make a claim under our Limited Warranty, you need to provide your
original purchase receipt with the purchase date and order number on it.
All work will be carried out by Laresar or its authorized agency.
Any replaced defective parts will become the property of Laresar.
Service under this warranty will not extend the period of this warranty.
If your machine is not functioning properly, or you still have any questions after reading this manual
carefully, please feel free to contact us, we will try our best to provide you with a satisfactory
solution.
This product must not be disposed of as household waste. Dispose of the device at an authorized
collection point for the recycling of electrical appliances.
The chemicals contained in the lithium-ion battery of the product will pollute the environment.
Please remove the battery before scrapping and send it to a professional battery recycling station
for centralized disposal.
The following information is only applicable to the discarding of the sweeping and mopping robot
and not to daily operation.
Make the robot vacuum run to a low battery level at which the robot cannot perform the
cleaning task without contacting the dust collection charging pile.
Turn off the robot vacuum.
Remove the side brush and the mop cloth support of the robot.
Unscrew the bottom cover of the robot cleaner, and remove the bottom cover.
Pull out the connector plug of the battery, and remove the battery.
Email to Our Customer Service:
[e-mail]
Laresar is here to help and we are glad to serve you.
To remove the battery, make sure that the battery is exhausted and the product is discon-
nected from the dust collection charging pile.
Please remove the battery pack as a whole. Do not damage the battery pack case to avoid
short circuit or leakage of hazardous substances.
If you contact substances leaking from the battery by accident, wash the contact part with
plenty of water and see a doctor in time.
18
EN
If you have any questions, please email to [e-mail]

Contact Information
laresar
[e-mail]
Contact us- We will get back to you
within 1 business day.
208-210015