Larson Electronics EXPCMR-WIP-RPS-OZ-2MP-BC User manual

EXPCMR-WIP-RPS-OZ-2MP-BC
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 4
Explosion Proof Outdoor Security Camera
Rechargeable - Wireless Video Output - Adj Rail Mount
Instruction Manual
Thank you for your purchase of the Larson Electronics EXPCMR-WIP-RPS-OZ-2MP-BC.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. WHEN EXTENSION
CORD IS CONNECTED TO A POWER SOURCE IN HAZARDOUS AREA, PLUG AND MATCHING RECEPTACLE
MUST BE SUITABLE FOR HAZARDOUS LOCATION INVOLVED. IMPROPER USE OF THIS DEVICE, ASSOCIATED
PLUG, RECEPTACLE, AND CORD CAN LEAD TO SERIOUS INJURIES OR DEATH TO PERSONNEL.
PERIODIC INSPECTION OF THE RECEPTACLE AND CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY
ARE FOUND, THE CORD MUST BE REPLACED BEFORE RESUMING USE OF THE UNIT.
ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND MAINTENANCE.
INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND COMPETENT
ELECTRICIAN.
IF ANY PARTS OF THE RECEPTACLE OR PLUG APPEAR TO BE MISSING, BROKEN, OR SHOW SIGNS OR
DAMAGE, DISCONTINUE USE IMMEDIATELY. REPLACE WITH THE PROPER REPLACEMENT PART(S) BEFORE
CONTINUING SERVICE.

EXPCMR-WIP-RPS-OZ-2MP-BC
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 4
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OFTHIS DEVICE. IF WIRING OR UNIT REPLACEMENT
INSTRUCTIONS ARE NOT FOLLOWED EXACTLY, THE FIXTURE MAY NOT BE SUITABLE FOR THE HAZARDOUS LOCATION INVOLVED.
WHEN HANDLAMP ISCONNECTED TO A POWER SOURCE IN HAZARDOUS AREA, PLUG AND MATCHING RECEPTACLE MUST BE
SUITABLE FOR HAZARDOUS LOCATION INVOLVED. WHEN FIXTURE IS CONNECTED TO POWER SOURCES OUTSIDE OFHAZARDOUS
AREA, STANDARD DUTY PLUGS AND RECEPTACLES MAY BE USED.
STANDARD PLUG AND TRANSFORMER MUST ONLY BE CONNECTED TO ARECEPTACLE LOCATED OUTSIDE THE
HAZARDOUS AREA!
IMPROPER USE OF THIS FIXTURE,ASSOCIATED PLUG, RECEPTACLE, AND CORD CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE FIXTURE AND CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND, THE CORD MUST
BE REPLACED BEFORE RESUMING USE OF THE HANDLAMP.
THE GLOBE IS MADE OF TEMPERED GLASS. IF THIS GLASS BECOMES SCRATCHED OR CHIPPED IT SHOULD BE REPLACED IMMEDIATELY.
The EXPCMR-WIP-RPS-OZ-2MP-BC from Larson Electronics is an Explosion Proof Outdoor Security Camera for
flammable work sites, harsh environments and outdoor locations. This IP66-rated device is rechargeable and offers
wireless video output and connection to other devices. Capable of producing clear, 1080p HD images, the unit features an
adjustable rail mounting system for versatile applications around the work site.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 12V DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Exp Cord Cap
Position device near work area for operation. Run cable to nearby power
source. Insert and twist-lock explosion-proof plug into a compatible receptacle within
the hazardous environment. See plug operation below.
PLUG OPERATION
Electrical connection between plug and compatible receptacle is accomplished
after plug fully inserts into receptacle and rotated clockwise.
1. Lift receptacle door and locate polarization on mating plug pin and
receptacle face. Insert plug straight all the way into receptacle until it
cannot go further.
2. Rotate plug clockwise limit (37º), this closes internal contacts and
completes circuit. This also mechanically locks plug into receptacle so it
cannot be pulled out.
3. To remove plug, push plug inward and turn to counterclockwise, pull plug
straight out.
Low Voltage DC
Connect power to power supply outputting low voltage at 12 Volts DC. This
variable voltage allows greater versatility without affecting light output. Ensure
deutsch connectors are properly connected (If applicable)

EXPCMR-WIP-RPS-OZ-2MP-BC
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 3of 4
CAMERA FEATURES
The EXPCMR-WIP-RPS-OZ-2MP-BC security camera provides operators in hazardous areas with crisp 1080p HD images. Equipped
with a 2 MP lens, up to 6x digital zoom is possible with the fixed-focus device. A cutting-edge chipset facilitates image compression and
video processing with superior quality. Operating at 5 watts, the explosion proof monitoring device is rechargeable, with up to 8 hours of
runtime per full charge. Video output and connection to other devices is wireless (no cords).
DURABILITY
The EXPCMR-WIP-RPS-OZ-2MP-BC is rated NEMA Type 3, 4, 4X, 7 (B,C,D) and 9 (E,F,G) and designed to withstand the rigors of
demanding environmental and operating conditions while remaining lightweight and easy to use. The housings are formed from extruded
aluminum and the lenses are unbreakable polycarbonate.
The explosion proof security device is designed to perform under harsh and rugged conditions. This IP66 rated waterproof unit resists the
corrosive effects of weather, dust, dirt, and humidity. This Class I Divisions 1 & 2, Class II Divisions 1 & 2, Class III Divisions 1 & 2 rated
camera provides property and product security while protecting operators with its safe and reliable explosion proof and weatherproof
design.
SECURITY & REMOTE ACCESS
The EXPCMR-WIP-RPS-OZ-2MP-BC supports several forms of security. The supported forms include WEP Encryption, WPA Encryption
and WPA2 Encryption. This explosion proof outdoor security camera also features remote access capability. It supports both P2P and
DDNS remote access.
WI-FI
The EXPCMR-WIP-RPS-OZ-2MP-BC is Wi-Fi compliant with wireless standards IEEE 802.11 b/g/n. On IEEE802.11b, this camera
transfers data at a maximum rate of 15Mbps. On IEEE802.11g, the max data transfer rate is 54Mbps. The max data transfer rate on
IEEE802.11n is 150Mbps.
WIRELESS NETWORK
The explosion proof camera allows operators to create their own 2.4Ghz and 5Ghz wireless network. This feature makes networks for
cameras easier to setup in outdoor sites. A QR code on the unit can be scanned for seamless wireless network configuration. The network
faciliates the connection of various devices. During use, footage is stored via internal memory.
BATTERY/CHARGING
This unit is powered by a rechargeable 8.8aH lithium ion battery. At a full charge, the explosion proof device provides a runtime of 8 hours.
For charging in non-hazardous locations, operators can use an included, standard 120-240V outlet charger.
MOUNTING
The EXPCMR-WIP-RPS-OZ-2MP-BC can be mounted on rails, such as forklift railings, using an adjustable rail mount system. This
component is easily detachable for charging, transportation or storage. The adjustable rail mount is offered in the following sizes for
compatibility: 1.5", 2", 3" or 4".
CAMERA SPECIFICATIONS
Dimensions: 18"W x 8"D x 6"H
Voltage: 12V DC
Watts: 5W
Image Sensor: CMOS
Display Resolution: 1920 x 1080
Video Resolutions: 1080p (1920 x 1080), 720p (1280 x 720), VGA (640 x 480), QVGA (320 x 240)
Lens: 2.8-4mm Focal Length
View: 30` Max Distance
Angle of View: Horizontal: 106°, Diagonal: 118° @ f = 2.8mm; Horizontal: 70°, Diagonal: 78° @ f = 4mm
Video Framerate: 30fps (60Hz), 25fps (50Hz), Downward Adjustable
Video Output: Wireless
Wireless Standard: IEEE802.11b / g / n
Data Rate: IEEE802.11b - 11Mbps (Max); IEEE802.11g - 54Mbps (Max); IEEE802.11n - 150Mbps (Max)
Frequency Bands: 2412 - 2472 MHz
Remote Access: Supports P2P & DDNS
Wireless Security: Supports WEP, WPA & WPA2
Maximum Power: 18dBm
Battery: 8.8aH Lithium-ion, Rechargeable
Runtime: 8 Hours per Charge
Charger: 120-240V Non-explosion Proof Charger

EXPCMR-WIP-RPS-OZ-2MP-BC
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 4of 4
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EXPCMR-WIP-RPS-OZ-2MP-BC is designed to provide years of reliable performance. Should the need for
replacement parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.