Lazer3D LZX-15 User manual

LZX-15 User Manual
LAZER3D
PERFORMANCE SFF PC CASES

Lazer3D LZX-15 Instruction Manual
PAGE CONTENTS
1 Contents
2 Specification
3 Component List and Tips
4 Quick Assembly Reference
5 - 6 Main Panels Assembly
7 Corner Columns
8 - 10 Internal Frame Assembly
11 Front Case Fans
12 Support Rail Assembly
13 - 14 PSU + GPU Mounting
15 - 16 Storage Options
17 - 18 Case Cooling Options
19 Internal PSU Cable
20 Side Panels
21 Top Panel
22 Case Feet
23 - 24 Vertical Stand Assembly
25 - 26 Reference Diagrams
Page 1
LAZER3D
PERFORMANCE SFF PC CASES

Page 2
LAZER3D
PERFORMANCE SFF PC CASES
SPECIFICATION

WARNING: The case is not at full strength until fully built,
please take care when assembling.
WARNING: Do not over-tighten the screws when securing
the panels as this can reduce thread life.
NOTE:
Peel off protective film
from BOTH sides of
each panel before
assembling the case.
COMPONENT LIST
LAZER3D
PERFORMANCE SFF PC CASES
Page 3

Page 4
LAZER3D
PERFORMANCE SFF PC CASES
QUICK ASSEMBLY REFERENCE
PLEASE READ THESE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THE CASE

Page 5
LAZER3D
PERFORMANCE SFF PC CASES
1
Don’t forget to
insert your IO Shield!
Attach 2x metal blocks
to the rear panel with 2x
M3x8mm Screws
3
ASSEMBLY TIP:
Use a PH1 screwdriver with the M3x8 and M3x5 screws
2Attach I/O board
to rear panel with
2x M3x6mm
Screws

Page 6
LAZER3D
PERFORMANCE SFF PC CASES
Attach the rear panel to
the the base panel with 2x
M3x8mm Screws
4
Attach 3x metal blocks
to the base panel with 3x
M3x8mm Screws
Mount Power Button
to IO Panel
5
6
7
Attach IO Panel to Rear Panel
with 2x M3x8mm Screws

Page 7
LAZER3D
PERFORMANCE SFF PC CASES
8Attach the 2x Corner Pieces to the base
panel with 2x M3x8mm screws.
Orientate corners with
thicker edge facing the
front of the case
FRONT EDGE
CORNER COLUMNS
9

Page 8
LAZER3D
PERFORMANCE SFF PC CASES
INTERNAL FRAME SUPPORTS
For Mini-ITX motherboard layout at-
tach 4x metal blocks with 4x M3x8mm
Screws to these 4 support types in
these orientations
Mini-ITX Layout
Micro-ATX Layout
10a
10b For Micro-ATX attach 4x metal blocks
with 4x M3x8mm Screws to these 4
support types in these orientations

Page 9
LAZER3D
PERFORMANCE SFF PC CASES
12a
MINI-ITX LAYOUT
11a
TIP - Connect wiring for
power button and I/O
panel to your motheboard
Using 4 x M3x6mm screws mount
your motherboard (with CPU cooler,
RAM and memory pre-assembled) to
the base panel
Attach the 4
frame supports
to the base
panel with 4 x
M3x8mm screws

Page 10
LAZER3D
PERFORMANCE SFF PC CASES
MICRO-ATX LAYOUT
11b Using 9 x M3x6mm
screws mount your
motherboard (with
CPU cooler, RAM
and memory pre-
assembled) to the
base panel
TIP - Connect wiring for
power button and I/O
panel to your motheboard
12b
Attach the 4
frame supports
to the base
panel with 4 x
M3x8mm screws

Page 11
LAZER3D
PERFORMANCE SFF PC CASES
Up to 2x 120mm case
fans can be mounted
to the bracket
FRONT FAN BRACKET
13
Alternatively, mount 1 x
3.5” hard drive
Cables pass through
this cutout once
slotted onto base
Or, 1 x 120mm
fan and 1 x
2.5” drive
Slot assembled
bracket into base
panel
14
pass cables
through this
gap when
inserting this
panel

Page 12
LAZER3D
PERFORMANCE SFF PC CASES
15
16
RAIL TYPE - A
RAIL TYPE - B
RAIL TYPE - C
For Graphics Cards that require 180 degree
PCIe power adapter
For Mini-ITX motherboard Setup
Standard Rail used for Micro-ATX Setup
MOUNTING RAILS
This third mounting
rail is OPTIONAL - only
required if you need
to mount additional
hardware such as extra
storage drives
Slot mounting rails
into rear panel slots
and fan bracket slots
Secure mounting
rails to supports
using 4 x M3x8mm
screws

Page 13
LAZER3D
PERFORMANCE SFF PC CASES
17 Secure power supply to support
rails with 4 x PSU screws
18
Mount your
Graphics Card or PCI
expansion card(s)
into the relevant
motherboard slot(s)

Page 14
LAZER3D
PERFORMANCE SFF PC CASES
Secure PCIe expansion
cards onto the rear
panel using the
relevant slot covers
with M3x8mm screws
Micro-ATX boards
have multiple slots,
you can use the
relevant different
covers to block any
usused rear slots
This example shows a
dual slot card taking
up slot 2 and 3, with
slots 1 and 4 being
covered.
19
Mini-ITX boards
generally will
require slot 3 - 4 to
be covered like this
example
20

Page 15
LAZER3D
PERFORMANCE SFF PC CASES
21
When using Mini-ITX
motherboard:
Up to 3 x 3.5” drives can be
stacked together.
Use M3x6mm screws
Or, mount 2 x 2.5” drives flat
to the bracket for use with
Micro-ATX motherboards
Or for Mini-ITX you can also
stack multiple 2.5” drives on
their side.
STORAGE OPTIONS

Page 16
LAZER3D
PERFORMANCE SFF PC CASES
23 The mounting rails
also provide additional
mounting positions for up
to 3 extra 2.5” drives
22 Once your storage drives
have been mounted to
the brackets, slot the
assembled unit onto
mounting rails in your
desired position

Page 17
LAZER3D
PERFORMANCE SFF PC CASES
24
Secure your 120mm
and 140mm case fans to
the relevant fan brackets
using Fan Screws, the assembled
units can then be placed onto the
mounting rail
25 Fan brackets can
also be used to
attach radiators or
AIO coolers to the
mounting rails
Mini-ITX compatible
with up to 240mm AIO Micro-ATX compatible
with up to 140mm AIO
CASE COOLING

Page 18
LAZER3D
PERFORMANCE SFF PC CASES
26
Using this fan bracket, 2 x 80mm
case fans can be attached sideways to the
mounting rail. Compatibility is dependant on
the CPU cooler installed
27 When using a Mini-ITX
motherboard 2 x 120mm
fans can be mounted to
the GPU side panel
Alternatively, a slim
240mm radiator/AIO can be
installed onto the side panel

Page 19
LAZER3D
PERFORMANCE SFF PC CASES
28
TIP - Don’t forget to turn on your
power supply on/off switch!
29
for Micro-ATX layout, 2 x 2.5”
drives can be installed above
the PSU here
Plug the power extension
cable into the power supply
30 Secure femal end
of power cable
to the rear of
the case with 2 x
M3x8mm screws