LC kids 2830-8900 User manual

Assembly Instruction 2830-8900 CRIB MADISON
Page 1 of 6
WARNING:
Do not use this crib if the enclosed or attached instructions cannot be strictly
adhered to. Do not use this crib if the child is able to climb out unaided or is taller
than 89 cm. Do not place cords, straps or similar items that could become wound
around the child’s neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress used with this
crib should not be more than 15 cm thick and should be of such length and width
that the gap between the mattress and the sides of the crib is not more than 3 cm
when the mattress is pushed into the corner of the crib.
09-004
WARNING:
Failure to follow these warnings and assembly instructions could result in serious
injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR
FUTURE USE.
Never use plastic shipping bags or other plastic film as mattress covers
because they can cause suffocation.
Infants can suffocate in gaps between the crib sides and a mattress that is
too small.
Infants can suffocate on soft bedding. Never add a pillow or comforter.
Never place additional padding under an infant.
To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their backs to sleep, unless otherwise advised by your physician.
STRANGULATION HAZARD: Strings can cause strangulation! Do not
place items with a string around a child’s neck, such as hood strings or
pacifier cords. Do not suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of
the body or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may
strangle a child.
FALL HAZARD: When child is able to pull to a standing position, set
mattress to lowest position and remove bumper pads, large toys and other
objects that could serve as steps for climbing out.
Stop using crib when child begins to climb out or reaches the height of 35
in. (89cm).
Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts or sharp edges before and after assembly and
frequently during use. Securely tighten loose bolts and other fasteners. DO
NOT use crib if any parts are missing, damaged or broken. Contact Legacy
Classic Kids for replacement parts and instructional literature if needed. DO

Assembly Instruction 2830-8900 CRIB MADISON
Page 2 of 6
NOT substitute parts.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged, cracked or loose. NOTE: This is only for
cribs with teething rails.
If refinishing, use a non-toxic finish specified for children’s products.
Follow warnings on all products in a crib.
09-005
CAUTION: ANY MATTRESS USED IN
THIS CRIB MUST BE AT LEAST 27 ¼ in.
(69CM) BY 51 5/8 in. (131CM) WITH A
THICKNESS NOT EXCEEDING 6 in. (15
CM)
09-003
IMPORTANT SAFETY INSTRUCTIONS:
Please carefully read all instructions and warnings before assembling the crib.
Use only vendor’s supplied hardware to assemble. Using unauthorized hardware could jeopardize the
structural integrity of the item.
For your safety and ease, assembly by two or more adults is recommended.
Keep instructions for future use.
PARTS INCLUDED:
(A) Left Side Gate - 1 pc
(D) Crib Back Head Board – 1 pc
(B) Right Side Gate - 1 pc
(
C
)
Mattress Metal Base
–
1
p
c
(E) Front Gate Foot Board- 1 pc

Assembly Instruction 2830-8900 CRIB MADISON
Page 3 of 6
HARDWARE ENCLOSED:
(F) Hex bolt screws: M6 x 38 – 8 pcs
(G) Bottom head bolt M6 x 17 – 4 pcs
(H) Lock washer M6 – 12 pcs (I) Flat washer M6– 12 pcs
NOTE: Store all hardware out of child’s reach.
TOOLS REQUIRED:
(J) Hex Allen Wrench with Ball tip -1 pc (included) Phillips Screwdriver (not included)
PRE- ASSEMBLY:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work
surface, as this will avoid damaging parts during assembly. The shipping box provides an ideal work
surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists above to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
The use of power tools for assembly is not recommended. Power tools can damage hardware or split
wood.
ASSEMBLY INSTRUCTIONS:
1. Remove the assembly instructions from the envelope attached to the Crib and review. Keep them handy
for referring to the part and hardware descriptions.
2. Assemble the Left Side Gate (A) and Right Side Gate (B) to the Mattress Metal Base Brackets (C) with 4
Bolts (G), Lock washer (H), Flat washer (I), using the Hex Allen Wrench (J). Adjust the brackets of the
Mattress Metal Base (C) to fit the hole of Side Gate when assembling (See Fig 1).
NOTE: The Mattress support base may be at the highest level when the child is born. It must be at the
lowest level by the time the child can stand up.

Assembly Instruction 2830-8900 CRIB MADISON
Page 4 of 6
3. To change the position of the Mattress Metal Base (C), unscrew the 4 bolts (G), Lock washer (H), Flat
washer (I), line up the Mattress Metal Base (C) with the holes at the desired height and re-attach the
Mattress Metal Base (C) with the same bolts (G), Lock washer (H), Flat washer (I).
4. Assemble the Crib Back (D) to the Left Side Gate (A) and to the Right Side Gate (B) with 4 Bolts (F),
Lock washer (H), Flat washer (I), using the Hex Allen Wrench (J) (see Fig 2).
Fig (1)
Fig (2)

Assembly Instruction 2830-8900 CRIB MADISON
Page 5 of 6
5. Assemble the Front Gate (E) to the crib using 4 same Bolts (F), Lock washer (H), Flat washer (I). Tighten
using the Hex Allen Wrench (J). (See Fig 3)
6. Tighten all connections. Assembly is complete.
NOTE:
As this Crib is designed to grow with your child, please retain these instructions as well as all hardware
for future use. Always keep all small parts and hardware out of children’s reach.
With the addition of this Crib Conversion Kit (sold separately), your Legacy Classic crib will become a
Toddler Bed/Daybed. Please see the Assembly Instructions included with the Legacy Classic Toddler
Bed/Daybed for details
Fig (3)
Fig (4)

Assembly Instruction 2830-8900 CRIB MADISON
Page 6 of 6
CARE INSTRUCTIONS
Dust often using a clean, soft, dry lint-free cloth.
Blot spills immediately, and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered
finish.
If the crib is to be stored, store in cool dry place and carefully package all original hardware to protect
from loss or damage.
Check fasteners periodically for tightness. DO NOT over tighten. This may cause distortion or breakage
This Crib can be converted to a Full SiHe Bed with the purchase of Legacy Classic Bed rail. You will be provided
4 pcs flat head bolt M6 x 13, 8pcs bolt M6 x 62mm, to attach the Bed rail into your Crib. Follow the instruction
below with two adults:
PARTS INCLUDED:
(L) Flat head bolts M6 x 13 – 4 pcs
(K) Hex bolt screws: M6 x 62 – 8 pcs
ASSEMBLY INSTRUCTIONS:
1. Disassemble your Crib or Toddler Bed/Daybed and set all pieces and hardware aside in an organiHed
manner.
2. Keep the Headboard and the Footboard upright.
3. Assemble the Side Rail to the Headboard and the Footboard with 8 bolts (K). To change the position of
the side rail, unscrew 4 bolts (K), line up the Side rail with the holes at the desired height and re-attach
the Side rail with the same bolts (K).
4. Insert the flat head bolts (L) into the upper hole of the Headboard and the Footboard to keep out of the
children’s reach
5. Tighten all connections. Assembly is complete.
THANK YOU FOR YOUR PURCHASE.
www.legacyclassickids.com
High Point, NC. 336 449 – 4600