LCUT Creative B 00-34 OO User manual

Bundle contains:
 1x LCC 00-09
 1x LCC 03-79
 1x LCC 03-80
 1x LCC 03-81
 1x LCC 03-82
 1x LCC 03-83
 1x LCC 03-84
 1x LCC 03-85
LCC Modelling System
B 00-34 OO gauge LNER style signal box
All drawings are not in scale. Some proportions on draw-
ings may differ from reality.
This bundle can be assembled with either left or right stair option out of the box
Left version show in this manual
For additional elements for modification and extension please visit our website at
www.lcut.co.uk or email us at [email protected]
Width: 137mm (With stairs) Depth: 54mm (Total) Height: 86mm
 1x LCC 03-86
 1x LCC 03-87
 1x LCC 03-88
 1x LCC 03-89
 1x LCC 03-90
 1x LCC 03-91
 2x LCC 03-92
 1x LCC 03-93
 3x LCC 03-94
We recommend PVA or any other paper/wood glue for the main fibre board parts
and resin based glue for 3D printed parts if present.
Painting recommendation: We recommend using acrylic or enamel paints. There is
no need to undercoat the surface but it can be done if desired. The material used is
porous and relatively forgiving, heavy coats are unlikely to flood the brickwork. If you
experience any warping in the material leave it to fully dry and then gently bend it
back into shape. Always test any paints in an area that will not be seen or on spare
parts/off cuts.
!
WINDOWS AND DOORS
PAGE 1 OUT OF 4

PAGE 2 OUT OF 4
Start the main assembly by joining either the
front or the back wall to one of the side walls.
Use the floor to strengthen the walls as well
as keep them square to each other. Make
sure that the back and front walls are overlap-
ping the side walls (the notches near gable on
side walls should not be sticking out but be
over the front or back wall.
Use the supports from the LCC 03-93 floor kit
to ensure the floor is supported at the 4 cor-
ners and is placed at even height.
Finish the main body with the remaining walls.
MAIN BODY
Use the diagrams on previous
and this page to mount the win-
dows and doors in the signal box.
Pay attention to how the windows
on side elevations are positioned.
The sliding, top, windows should
be facing the rear of the signal
box.
Generally it is advisable to glue
in the windows and doors after
the signal box body is painted.
This way crisper and cleaner
lines between them can be
achieved.

PAGE 3 OUT OF 4
Use the 3 diagrams above to position the
raised woodwork elements over the signal
box front and back elevations. Not the ele-
ment B needs to be cut along the scored
lines to fit in place.
If assembling the roof separate
(removable) glue the LCC 03-94 supports
to the roof tile panels LCC 03-92. Other-
wise glue them to the signal box body.
The barge boards LCC 03-91 should be
glued to the roof tile panels about flush
with the cut out in the top edge of the roof
tile panel. They also should not be touch-
ing the signal box body. Use the provided
LCC 00-09 roof tile strips to complete the
roof.
The balcony can be assembled
either in the full version or in the
front wall version only. Glue the
supports from LCC 03-88 to the
bottom of the balconies. Mind the
cut outs in the balcony so that it
clears the raised woodwork and
sits flush on the signal box front
wall. Glue the balcony to the sig-
nal box one plank below the win-
dows (the supports should clear
the raised woodwork).

PAGE 4 OUT OF 4
Diagram above shows the assembly of the stairs, stair balcony, and the priv.
Take care as the parts are thin and fragile. Start with the balcony floor. Use the 3 provided
strips to build up the thickness on the sides and front. Glue the supports to the bottom (making
sure to clear the lower door). Glue that assembly to the signal box.
Assemble the stairs by first inserting the steps in the side parts making sure not to use too
much force. Use glue as lubricant to make the insertion easier. The stairs can be put together
to suit either the left or right version of the signal box (left shown). Assemble them mirrored for
the right version.
Put the priv together and finish off with the leftover ridge tiles. Glue to the signal box making
sure it clears the upper door.
Finally glue the staircase to the balcony. The right angle balustrade should overlap the priv a
little bit.
Finished signal box shown below.