LCUT Creative B 00-33 User manual

Bundle contains:
 2x LCC 00-09
 1x LCC 03-00
 1x LCC 03-05
 1x LCC 03-17
 1x LCC 03-19
 1x LCC 03-59
 1x LCC 03-67
 1x LCC 03-68
 1x LCC 03-69
LCC Modelling System
B 00-33 Small L&CR/LMS signal box
All drawings are not in scale. Some proportions on draw-
ings may differ from reality.
This bundle can be assembled with either left or right stair option out of the box
Left version show in this manual
For additional elements for modification and extension please visit our website at
www.lcut.co.uk or email us at [email protected]
Width: 60mm (Body only) Depth: 52mm (Body only) Height: 75mm (Without chimney)
 1x LCC 03-70
 1x LCC 03-71
 1x LCC 03-72
 1x LCC 03-73
 1x LCC 03-74
 1x LCC 03-75
 1x LCC 03-76
 2x LCC 03-77
 1x LCC 03-78
We recommend PVA or any other paper/wood glue for the main fibre board parts
and resin based glue for 3D printed parts if present.
Painting recommendation: We recommend using acrylic or enamel paints. There is
no need to undercoat the surface but it can be done if desired. The material used is
porous and relatively forgiving, heavy coats are unlikely to flood the brickwork. If you
experience any warping in the material leave it to fully dry and then gently bend it
back into shape. Always test any paints in an area that will not be seen or on spare
parts/off cuts.
!
WINDOWS AND DOORS LAMINATES
It is recommended to start the assembly
with laminating windows and doors pan-
els. Cut parts from their respective
spruces. Spread glue thinly on the back
of the frontal part. Align and press both
parts together. If more watery glue is
used the parts will try to warp signifi-
cantly. It is recommended to press the
laminated parts in between two heavy
and flat surfaces (like heavy hardback
books, care should be taken not to allow
the laminated parts stick to the books by
removing the squezeout [excess glue]
and or lining the press with non stick ma-
terial). When glue has dried the parts will
stay flat. Ensure the parts are lined up
correctly!
PAGE 1 OUT OF 3

While the laminates are drying glue the
walls together. It is recommended to glue in
the remaining parts from LCC 03-67 and
LCC 03-68 before gluing walls but it can be
done afterwards. Glue the front lower win-
dows flush with the back of LCC 03-00 and
the right side lower door flush with the back
of LCC 03-75 (door shown on previous
page). Recommended way of gluing walls is
to apply glue to the back of the interlocking
bricks. Additional glue can be applied to the
spaces between the interlocking bricks but
that will increase the squeezeout. Care
should be taken not to put too much glue or
let it harden fully before fitting the supports
and the floor.
Next step in assembly is to complete the in-
ternal structure of the signal box. Ideally it
should be done while the glue from previous
step is not dry yet. Glue the short strips from
LCC 03-17 in the corners of signal box. En-
sure they are flush with the bottom of the
signal box. After that glue in the floor or
leave it out if to make assembling interior
easier. Now leave the model to dry enough
that the walls do not come apart when floor
is installed. Floor is designed to be very
tightly fitting. In rare instance the floor will
seem too big. In such case it is possible to
gently force it into position which should be
on top of the four short strips. There is a
small chance that the floor pushes the walls
apart. If this appear to happen take the floor
out and trim slightly. It is also possible to
clamp the model gently to ensure there is no
gaps at the corners.
Next step in assembly is gluing the lami-
nates to the signal box body. Start with LCC
03-68 and LCC 03-71. Follow with the two
remaining elements. Ensure that the parts
marked blue are glued in flush with the out-
side of the signal box.
Recommended glue
application position
PAGE 2 OUT OF 3

Remove roof support parts LCC 03-76 from their spruce and glue together by slotting together as
shown on picture above. Leave them until glue dries prior making sure they are all at right angles to
each other. Take out LCC 03-77 roof panels from their spruce and start gluing them to the supports.
Assemble on a flat surface ensuring the roof is square on edges and flat on the bottom.
Assemble LCC 03-78 ensuring there is no gaps on the corners. Glue the chimney assembly to the
roof in chosen place. Trim the provided stick to length and insert into the hole on top of the chimney.
Assemble the staircase by gently wiggling the steps into the slots. Use a little bit of PVA glue as a lu-
bricant to help the process. Care should be taken not to apply excessive force or the tabs will bend.
Glue the staircase to the signal box.
PAGE 3 OUT OF 3