LCUT Creative LCC B 70-30 User manual

!
LCC Modelling System
B 70-30 O gauge small drive through goods shed
All drawings are not in scale.
Some proportions on drawings may dier from reality.
For additional elements for modication and extensions please visit our website at
www.lcut.co.uk or email us at [email protected]
Building footprint: 162mm long x 198mm wide including canopy and loading platform
Bundle contains:
• 1x LCC 70-09
• 2x LCC 70-13DW
• 1x LCC 70-48
• 2x LCC 74-02
• 2x LCC 74-03
• 1x LCC 74-21
• 1x LCC 74-26
• 1x LCC 74-43
• 1x LCC 74-44
• 1x LCC 74-45
• 1x LCC 74-46
• 1x LCC 74-47
• 1x LCC 74-114
• 1x LCC 74-115
• 1x LCC 74-116
• 1x LCC 74-117
• 1x LCC 74-118
• 1x LCC 74-119
We recommend PVA or any other paper/wood glue for the main bre
board parts and resin based glue for 3D printed parts if present.
Painting recommendation:
We recommend using acrylic or enamel paints. There is no need to
undercoat the surface but it can be done if desired. The material used
is porous and relatively forgiving, heavy coats are unlikely to ood the
brickwork. If you experience any warping in the material leave it to fully
dry and then gently bend it back into shape. Always test any paints in
an area that will not be seen or on spare parts/o cuts.
REMOVING PART NUMBER TABS
PAGE 1 OUT OF 4
Using a ruler (ideally at steel one) remove tabs from the parts. Use multiple light passes
with a sharp hobby knife. Tab placement is usually in an area that will be covered with
something so small imperfections in cuts are usually not a problem.
CONNECTING PARTS
Recommended way of gluing parts
together is to apply PVA glue to the
interlocking bricks working from
back of the part to the front.
This ensures there will be no glue
overow on the front, visible side.
Then lay the part without glue on at
surface laying on its front (engraved
side). Press the part with glue onto
the part without glue. Gently push
parts together from sides to close
the gap. Corners follow a similar
procedure but at a right angle. Apply
glue only on the inner surface of the
corner joint

PAGE 2 OUT OF 4
ASSEMBLY
We recommend to paint the model as it is being assembled. Put the 4 walls together with
the inner platform, barge boards, facia boards, and the loading platform then pain that
assembly before tting the roof, canopy and the sliding gates.
Start by joining LCC 74-26 with LCC 74-114
and LCC 74-115. Make sure to glue in the
gate panels as shown on the diagram. The
wider parts should be facing the loading
door. Fit the inner platform which will
stabilise the construction.
Fit the back wall part number LCC 74-21.
Glue the barge boards LCC 74-117 to the
gate panels making sure they are well
aligned with the slopes of the gable.
Fit the facia boards LCC 74-119. Those need
trimming to length and should t well
without any gaps on the sides. Facia boards
should be glued in ush with the top edges
of LCC 74-21 and LCC 74-26. They should
also interface neatly with the barge boards.

PAGE 3 OUT OF 4
Trim the roof panels LCC 70-13DW to size.
They should end up approximately 164mm
wide and 88mm high. Make sure to cut them
oversized at rst and then t to exact size.
Roof panels should be resting with the edge
touching the facia boards and the ends
should be ush with the barge boards.
Standard roof tiles can be replaced with roof
tile strips BM 70-00 if desired (sold
separately).
Fit the prepared roof panels to the goods
shed. Cover the ridge with LCC 70-09 roof
ridge tiles which need to be cut to length.
Assemble the loading platform.
Assemble the steps as shown on the
diagram.
Ensure the wider part of the step is facing
towards the back of the steps.
If the steps are a tight t in the holes use a
rocking motion to gently encourage them to
t.
Glue the strapping to the gates.

PAGE 4 OUT OF 4
Assemble the sliding gates by rst
folding the tab on the ends of the rail
(only use one rail from the fret for this
kit). Glue the rail to the sliding gates
and then fold the tabs over to form a
hinge. Alternatively after gluing the
rail to the gates cut the tabs o from
the gates for easier and alternative
look.
Assemble the canopy as shown on
the diagram.
Fit the platform, steps, and the sliding
gates to the goods shed.
Fold the train gates LCC 74-02 and LCC
74-03 in half with some watered down
glue between. Make sure to align them
neatly and press them for a few minutes
between something heavy so they bond
well and are at.
Glue the gates in a desired position.
Finish the build by gluing the canopy over
the loading platform making sure it butts
up against the facia board.